31-10702 11-08 JR Installation Instructions Professional Outdoor Grills and Cooktop Tables de cuisson et barbecues de plein air professionnels Instructions d’installation La section française commence à la page 23 Parrillas y estufa profesionales para el aire libre Instrucciones de instalación La sección en español empieza en la página 45...
LP tank. Store the tank outdoors in a well ventilated area. • Do not store additional LP tanks in or near the gas grill. • Follow the guidelines on the LP tank for proper storage, transport and handling. IF YOU SMELL GAS: •...
Page 3
Installation Instructions FOR OUTDOOR USE ONLY IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THIS MANUAL THOROUGHLY BEFORE INSTALLATION, USE OR SERVICING THIS EQUIPMENT. CALIFORNIA PROPOSITION 65 WARNING: The burning of gas cooking fuel generates some by-products, which are on the list of substances, which are known by the State of California to cause cancer or reproductive harm.
Make Electrical Connections ...19 ZGG420NB, 42" Built-In Natural Gas ZGG420LB, 42" Built-In LP Gas ZGG542NC, 54" Natural Gas Grill with Cart and 2 Side Burners ZGG542LC, 54" LP Gas Grill with Cart and 2 Side Burners ZGG300NC, 30" Natural Gas Grill with Cart ZGG300NB, 30"...
PRODUCT DIMENSIONS AND CLEARANCES 54" Built-In 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 27" 42" Built-In 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 27" 30" Built-In 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 27"...
Page 6
PRODUCT DIMENSIONS AND CLEARANCES 54" Cart with Side Burners 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 15-1/2" (both sides) 27" 54" Cart 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 15-1/2" (both sides) 27"...
Page 7
Design Information PRODUCT DIMENSIONS AND CLEARANCES 42" Cart 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 15-1/2" (both sides) 51" 27" 41-7/8" 30" Cart 12" Min. to Combustibles 4" Min. Clearance for Lid to Non-Combustibles 15-1/2" (both sides) 51"...
ADVANCE PLANNING Built-In Monogram Outdoor Grills are designed for easy installation into a masonry, non-combustible enclosure. The grill drops into he opening and hangs from its side flanges. • A deck is not required for support from the bottom. • The cutout must be completely covered with non-combustible material such as stone, brick, ceramic tile, concrete board, etc.
ELECTRICAL SUPPLY REQUIREMENTS A 120-volt, 60Hz, 15-amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle at the rear and below the cutout. Electrical must be located within reach of the 6-ft.
OUTDOOR GRILL, COOKTOP AND ACCESSORY CUTOUT DIMENSIONS 28-3/4" for 30" Models Between Cutouts 40-3/4" for 42" Models 52-3/4" for 54" Models 24-1/2" Grill Cutout Access Doors 1-1/8" 36" ZX27AD Min. Min. Gas and Electrical Locations 10" Min. 3-1/2" 3-1/2" 7-3/8" 3-1/2"...
TOOLS REQUIRED Saber Saw Measuring Tape Carpenter’s Square Safety Glasses Phillips #2 Screwdriver Level Pliers Utility Knife MATERIALS REQUIRED (not provided) Pipe Joint Sealant Pipe Fittings (approved type and resistant to LP or natural gas) Use stainless steel or flexible metal gas line to reach the built-in installation location or cart model location (if natural or whole-house LP).
REMOVE PACKAGING FROM CART MODELS 1. Cut the banding. Use a box cutter or utility knife to score and cut the carton along the base (or remove the staples with a staple remover or a screwdriver). 2. Lift the carton straight up and off of the grill. 3.
REMOVE PACKAGING FROM CART MODELS (cont.) 8. Position the blade of the dolly next to the right side of the grill. Tilt the grill back and away to allow blade to slip under the wheels. NOTE: The wheels must rest on the blade of the appliance dolly.
REMOVE PACKAGING FROM BUILT-IN MODELS 1. Cut the banding. Use a box cutter or utility knife to score and cut the carton along the base (or remove the staples with a staple remover or a screwdriver). 2. Lift the carton straight up and off of the grill. 3.
Open the tank valve when ready to use the grill. Always close the tank valve when cooking is complete. LP GAS GRILL CONNECTIONS TO A GRILL OR COOKTOP LP Gas Cooktop and Grill Combination Connections Use this method to connect a single tank to both appliances.
LP GAS GRILL CONNECTIONS TO A GRILL OR COOKTOP (cont.) Single Gas Cooktop or Grill Connection 3/8” Flare Fitting 20-lb. Type 1 LP Tank Built-in models shown. For models installed on carts, open the tank storage drawer on the right side to make the tank connection.
WARNING: TEST FOR LEAKS A complete gas tightness check must be performed at the installation site. CAUTION: To prevent fire or explosion hazard, DO NOT use or permit sources of ignition in the area while performing a leak test. Perform leak test outdoors only. Never perform a leak test with fire or flame.
INSTALL BRACKET WITH TRANSFORMER (Built-In Models Only) • Mount the bracket to the back wall of the enclosure with 4 screws (not supplied). • Slide the battery compartment from the top, straight down, engaging the side slots. Bracket Side Slots INSTALL COOKTOP BRACKET WITH BATTERY COMPARTMENT •...
Page 20
Installation Instructions 24-1/8" 24-1/8" Double Access Double Access Doors Doors • Cut the opening to the dimensions shown. Reinforce the inside of the opening using at least 1" wide material surround to accept the frame-mounting screws. • Place the frame into the opening and secure with screws (provided) on all sides as shown.
Page 21
Installation Instructions 2-Drawer Storage 18-9/16" ZX18DS 17-1/4" 10-1/8" 24-1/8" 25-3/16" 18" 1-1/4" Drawer Overlap ZX18DS STORAGE DRAWER IMPORTANT: The supplied rear support bracket adjusts from 4-1/8 " to 6-7/8 " . When using the supplied bracket, cut the opening at least 4-1/8 " above the floor.
Page 22
Installation Instructions 16" 24" Spring Hinge Clips (2) ZX18TC TRASH BIN • Cut the opening to the dimensions shown. Reinforce the inside of the opening using at least 1 " wide material surround to accept the frame-mounting screws. NOTE: If you are installing another accessory into the same enclosure, measure and cut the openings to accommodate the bottom overlaps and align them evenly across the bottom.