Care And Cleaning; Cleaning Agents; Detaching And Refitting The Rails - Siemens HB13AB.23B Instruction Manual

Built-in oven
Table of Contents

Advertisement

Care and cleaning

With good care and cleaning, your oven will remain clean and
fully-functioning for a long time to come. Here we will explain
how to maintain and clean your oven correctly.
Notes
Slight differences in the colours on the front of the oven are
caused by the use of different materials, such as glass,
plastic and metal.
Shadows on the door panel which look like streaks, are
caused by reflections made by the oven light.
Enamel is baked on at very high temperatures. This can
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.

Cleaning agents

To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use
sharp or abrasive cleaning agents,
cleaning agents with a high concentration of alcohol,
hard scouring pads or sponges,
high-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
Area
Cleaning agents
Oven front
Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Do not use glass cleaners or
glass scrapers.
Stainless steel
Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Remove flecks of limescale,
grease, starch and albumin (e.g. egg
white) immediately. Corrosion can form
under such residues.
Special stainless steel cleaning prod-
ucts suitable for warm surfaces are avail-
able from our after-sales service or from
specialist retailers. Apply a thin layer of
the cleaning product with a soft cloth.
Door panels
Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Glass cover for the
Hot soapy water:
oven light
Clean with a dish cloth.
Seal
Hot soapy water:
Do not remove.
Clean with a dish cloth. Do not scour.
Shelves
Hot soapy water:
Soak and clean with a dish cloth or
brush.
Telescopic shelves Hot soapy water:
Clean with a dish cloth or a brush. Do
not soak or clean in the dishwasher.
Accessories
Hot soapy water:
Soak and clean with a dish cloth or
brush.
Cleaning the self-cleaning surfaces in the cooking
compartment
The back wall and ceiling of the cooking compartment are
coated with self-cleaning enamel. This coating absorbs and
removes splashes from baking and roasting while the oven is in
operation. The higher the temperature and the longer the oven
is in operation, the better the result will be.
If dirt is still visible even after several uses, clean the back wall
and ceiling with hot soapy water and a soft sponge.
Discolouration may occur over time that cannot be removed.
This does not damage the enamel.
Caution!
Damage to surfaces on self-cleaning areas due to applying
oven cleaner.Never clean the self-cleaning surfaces with oven
cleaner.
If oven cleaner accidentally gets onto self-cleaning surfaces,
remove it immediately with a sponge and plenty of water.
Caution!
Damage to surfaces on self-cleaning areas due to the use of
abrasive and acidic cleaning agents and aids.
Do not use cleaning agents containing abrasive substances or
acids.
Do not use abrasive cleaning aids such as steel wool or
scourers.
Cleaning the cooking compartment floor and side walls
Use a dish cloth and hot soapy water or a vinegar solution.
If there are heavy deposits of dirt, use a stainless steel scouring
pad or oven cleaner. Only use when the cooking compartment
is cold. Never treat the self-cleaning surfaces with a scouring
pad or oven cleaner.

Detaching and refitting the rails

The rails can be removed for cleaning. The oven must have
cooled down.
Detaching the rails
Lift up the front of the rail
1.
and unhook it (figure A).
2.
Then pull the whole rail forward
3.
and remove it (Fig. B).
4.
$


Clean the rails with cleaning agent and a sponge. For stubborn
deposits of dirt, use a brush.
Refitting the rails
First insert the rail into the rear socket, press it to the back
1.
slightly (figure A),
%


11

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents