1. Manuals
  2. Brands
  3. Barco Manuals
  4. Projector
  5. R9002120
  6. Installation manual

Barco R9002120 Installation Manual

Hide thumbs Also See for R9002120:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
DATA
708
R9002120
INSTALLATION MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Barco R9002120

Summary of Contents for Barco R9002120

  • Page 1 DATA R9002120 INSTALLATION MANUAL...
  • Page 3 BARCO PROJECTION SYSTEMS DATA R9002120 INSTALLATION MANUAL Date : Art. No. : 260597 R5975987...
  • Page 4 Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, May 1997. All rights reserved. Trademarks are the rights of their respective owners. BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium...

  • Page 5: Table Of Contents

    Table of Contents TABLE OF CONTENTS WARNINGS ....................................1-1 SAFETY INSTRUCTIONS ................................1-1 On safety ....................................1-2 On installation ..................................1-2 On servicing ..................................... 1-2 On cleaning ....................................1-2 On repacking .................................... 1-2 On illumination ..................................1-2 UNPACKING & DIMENSIONS ................................ 2-1 Unpacking ....................................
  • Page 6 Table of Contents i - 2 5975987 BARCODATA 708 260597...

  • Page 7: Warnings

    * All instructions for operating and use of this equipment must be projector. Record these numbers in the spaces provided below. followed precisely. Refer to them whenever you call upon your BARCO dealer regarding this product. On safety PART NUMBER : 1.

  • Page 8: On Installation

    Replacement parts - When replacement parts are required, be sure To disconnect the cord, pull it out by the plug. Never pull the cord the service technician has used original BARCO replacement parts or itself. authorized replacement parts which have the same characteristics as the BARCO original part.

  • Page 9: Unpacking & Dimensions

    Unpacking and Dimensions UNPACKING AND DIMENSIONS Unpacking To open de banding, pull on the clip as shown in the first drawing. Take the projector out of its shipping carton and place it on a table. Save the original shipping carton and packing material, they will come in handy if you ever have to ship your projector. For maximum protection, repack your projector as it was originally packed at the factory.

  • Page 10: Projector Dimensions

    Unpacking and Dimensions Projector dimensions (mm) 2 - 2 5975987 BARCODATA 708 260597...

  • Page 11: Installation Guidelines

    1.4m (4.6') to 7m (23') with an aspect ratio of 4 to 3. It leaves the BARCO factory, adjusted as a ceiling front projector for a screen width of 2.4m. Changing the image size from the factory preset requires a realignment of the projector.

  • Page 12: Where To Install The Projector

    To install the projector, apply always the BARCO kits which are specially designed for this function. BARCO ceiling support. Always use the BARCO ceiling support to attach your projector to the ceiling. (BARCO order number : R9827990) The installation instruction for this support is enclosed in the packet of the set.

  • Page 13: Installation Set Up

    Installation Set Up INSTALLATION SET UP Access to controls Opening procedure : During the projector set up and installation it is neces- sary to open the top cover. To gain access, procede as follow : *Turn both lock screws with a screwdriver or a coin counter clockwise.

  • Page 14: Scan Adaptation

    Installation Set Up Scan adaptation The scanning can be switch by turning the Horizontal and Vertical scan connectors and the convergence connectors. To change the scanning, it is necessary to open the projector top cover and to rotate the chassis. For opening the projector's top cover, see Getting access to controls.
  • Page 15 CHANGE LANGUAGE CHANGE PROJECTOR ADDRESS CHANGE BAUDRATE POWER UP MODE : operating Follow next procedure to check the configuration : BARCO LOGO - switch on the projector. Select with then <ENTER> - the projector starts up on the last selected source.
  • Page 16 Installation Set Up 5975977 BARCODATA 708 260597...

  • Page 17: Projector Set Up

    Projector Set Up PROJECTOR SET UP Projector Set Up strap The strap on the CPU unit allow a set up of the password mode. Gaining access to the strap - Open the top cover (see installation set up) Horizontal scan - Open the chassis (see installation set up) connectors Vertical scan...
  • Page 18 Projector Set Up 5975987 BARCODATA 708 260597...

  • Page 19: Power (Mains) Connection

    OFF ON Input power (mains) voltage adaptation. Attention The BARCODATA 708 - R9002120 leaves the factory to operate on a mains (power) input of 230 Vac. Adaptation of the power input of the projector from 230 VAC to 120 VAC or vice versa is possible. Follow the procedure as described below.

  • Page 20: Fuses

    For continued protection against fire hazard : - replace with the same type of fuse - refer replacement to qualified service personnel Fuse type : 2 x T5A/250V (Barco order number : R314104) Switching on/off The projector is switched ON and OFF using the power (mains) switch ON/OFF.

  • Page 21: Installation Adjustments

    Installation Adjustments INSTALLATION ADJUSTMENTS Entering the adjustment mode Press ADJUST to enter the adjustment mode. ADJUSTMENT MODE Select a path from below: GUIDED RANDOM ACCESS INSTALLATION SERVICE IRIS source 1 Select with then <ENTER> <EXIT> to return IRIS Installation (only for qualified technician) Random Access Service...

  • Page 22: Overview Flow Chart Installation Mode

    Installation Adjustments Overview flow chart installation mode. RASTER CENTERING OPTICAL LENS FOCUSING SCHEIMPFLUG ADJUSTMENT 1. LOOSEN THE NUT ON THE REAR OF THE XXXX LENS, CONTRAST LEVEL IS REDUCED ROTATE THE LENS BARREL AND BRIGHTNESS INCREASED LOOSEN THE 4 TO FOCUS THE CENTER TO MAKE THE RASTER LENS MOUNTING NUTS ON OF THE IMAGE,...
  • Page 23 When entering the installation mode, the projector will automatically ARE RESERVED TO, switch to the internal pattern on 15 kHz/50 Hz. AND TO BE PERFORMED ONLY BY BARCO PERSONNEL, OR BARCO AUTHORIZED DEALERS IF QUALIFIED, PRESS <ENTER> TO CONTINUE, OR ENTER asks for your password.

  • Page 24: Scheimpfug Adjustment

    Installation Adjustments Scheimpfug adjustment The scheimpfug correction can be adjusted separately for the three range 1 1.40m tubes within 3 ranges: min. SW : 1.40 m (55") max. SW : 1.90 m (75") 1.90m range 1 : 1.4 m (55") to 1.9 m (75"), optimum screen width 1.4 m (55") range 2 : 1.9 m (75") to 3.2 m (126"), optimum screen width 2.4 m (94")

  • Page 25: Optical Lens Focusing

    Installation Adjustments Optical lens focusing The optical focusing procedure is performed separately for each lens. The appropriate CRT will be switched on as the user proceeds OPTICAL LENS FOCUSING through the optical focusing adjustment sequence. 1. LOOSEN THE NUT ON THE REAR OF THE XXXX LENS, ROTATE THE LENS BARREL TO FOCUS THE CENTER...

  • Page 26: Raster Centering

    Installation Adjustments Raster centering The raster must be centered on the CRT screen surface of each tube, therefore, it is necessary to look into the lenses. Caution : To avoid eye discomfort while performing these adjust- ments, reduce the contrast and gradually increase the brightness level until the raster becomes visible behind the image.

  • Page 27: Crt Projection Angle Adjustment

    Installation Adjustments CRT projection angle adjustment The projection angle of the red and blue CRT's is dependent on the desired size of the projected image. If the centers of green, blue and red do not coincide, the CRT projection angle must be adjusted. Never try to correct this misalignment with the shift correction or the CRT PROJECTION ANGLE static convergence controls.
  • Page 28 Installation Adjustments A' A Screws A, B, C and D (M4) : upper fixation latch. nutdriver 7mm. Screw A', B', C' and D' (M4) : lower fixation latch. nutdriver 7mm. Loosen the four hexagon screws A, A', B and B', upper and lower fixation latch.

  • Page 29: Alignment Of The Projector

    Installation Adjustments After finishing the installation adjustments procedure, the 'Path selection' returns on the screen. You are now able to start the alignment procedure for the projector. You have the choice between: ADJUSTMENT MODE - Guided Adjustment Procedure GUIDED - Random Access Adjustment Procedure RANDOM ACCESS INSTALLATION SERVICE...
  • Page 30 Installation Adjustments 7-10 5975987 BARCODATA 708 260597...
  • Page 31 SAFETY NOTICE ment, otherwise press EXIT to return to the service menu. RISK OF ELECTRICAL SHOCK G2 ADJUSTMENT SHOULD BE PERFORMED BY BARCO PERSONNEL, OR BARCO AUTHORIZED DEALERS. IF QUALIFIED, PRESS <ENTER> TO CONTINUE, OR IF NOT, <EXIT> TO RETURN.

  • Page 32: Appendix A : G2 Adjustment

    G2 Adjustment A green LED for each color is mounted on the driver board, below the CRT's. When selecting the G2 adjustment menu, these green LEDs must be out. If not, follow the procedure to adjust the G2 : Loosen screws and move the cover plate to the left to access the G2 controls.
  • Page 33 Form Approved MATERIAL SAFETY DATA SHEET Bureau Budget No. 45-R0338 MANUFACTURER'S NAME AND FSCM (Federal Supply Code for Manufacturer's) EMERGENCY PHONE NO. BARCO N.V. 32-56-368211 ADDRESS (Number, Street, City, State, and ZIP Code) Noordlaan 5 B-8520 KUURNE CHEMICAL NAME AND SYNONYMS TRADE NAME AND SYNONYMS Ethylenglycol &...
  • Page 34 TRESHOLD LIMIT VALUE 100ppm EFFECTS OF OVEREXPOSURE EMERGENCY AND FIRST AID PROCEDURES CONDITIONS TO AVOID STABILITY UNSTABLE STABLE INCOMPATABILITY (Materials to avoid) HAZARDOUS DECOMPOSITION PRODUCTS CONDITIONS TO AVOID OCCUR HAZARDOUS POLYMERIZATION WILL NOT OCCUR STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED Rinse with water WASTE DISPOSAL METHOD RESPIRATORY PROTECTION (Specific type)

This manual is also suitable for:

Data 708

Table of Contents