Merlin MR850EVO Installation And Operating Instructions Manual
Rolling garage door opener
Hide thumbs
Also See for MR850EVO:
- Installation and operating instrictions (20 pages) ,
- Installation and operating instruction (24 pages) ,
- Installation and operating instructions manual (25 pages)
Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Merlin MR850EVO
Summary of Contents for Merlin MR850EVO
- Page 3 13 mm, 10 mm, 8 mm 5.5 mm Minimum distance from 95 mm edge of curtain to edge of door bracket 45 mm 95 mm...
-
Page 4: Safety Check
Non opener side Opener side SAFETY CHECK! - Page 5 Learn Limits button UP Arrow button DOWN Arrow Learn button Release cable button Rope Manual release Overhand knot warning label Release handle Pull down FIRMLY...
- Page 6 Release cable Rope Manual Release Overhand knot Warning Label Release handle...
- Page 7 Rope Door stand Rope Door stand...
- Page 8 Press and hold until FLASHING Right bank will light up (IF REQUIRED) To change press and hold until correct bank lights up Left bank will light up for Left hand installation Press & release to accept selected hand. Press and hold to drive door up to open If required: Use DOWN button to adjust Press &...
- Page 9 40 mm 40 mm Test obstacle Handle should be less than 1.8 m Wall control, or wireless push button no less than 1.5 m...
-
Page 10: Safety First
100 mm high obstacle at any point along the floor. Red LED Red LED MUST BE ON MUST BE O IR Beam IR Beam SAFETY FIRST! Protector System MR850EVO ONLY Black Yellow Learn Learn Button Button Down... - Page 11 TO ADD Transmitters / Wireless wall button Press and hold down the desired Button. LED will FLASH Press LEARN Release LRN button when Courtesy LEDs flashes once TO DELETE ALL REMOTES sec). Press LEARN for 9 seconds LED on WILL TURN ON After 9 seconds all remotes are deleted and LED will go out.
- Page 12 Locate the yellow learn button Press and release the yellow learn button Enter a 4-digit PIN of your choice ? ? ? ? _ _ _ _ Press and hold the enter button Opener light bulbs blink After the lights blink release the ENTER button...
- Page 14 MR850EVO ONLY External Device 12 vdc white/black white Keyswitch or push button white/black white...
- Page 15 MR850EVO ONLY...
- Page 16 041A6811-2 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazard. 001A6621 041A6812 026B0166 041B0655 041D7403 (MR850) 041D7403-1 (MR650) 001A6528 204D0250 (MR850) 204D0251 (MR650) 001B6681 002B1600 041B0641 (MR850)
- Page 20 Chamberlain Chamberlain’s warranty Liability – Australia only Liability – New Zealand only Note Chamberlain service centre contact details Australia New Zealand Exclusions...
Need help?
Do you have a question about the MR850EVO and is the answer not in the manual?
Questions and answers
My remote has suddenly begun operating a door across the street. How do I find out the code for my door so that I can change it?
To program your Merlin MR850EVO remote, follow these steps:
1. Ensure the motor is plugged in and powered on.
2. Locate the "Learn" button on the motor unit (a small yellow button).
3. Press and hold the button on the remote that you want to program.
4. Immediately release the yellow "Learn" button.
5. The motor light will flash, indicating the remote has been successfully programmed.
6. Test the remote button to confirm it is working.
If you need further adjustments or troubleshooting, refer to the manual or contact support.
This answer is automatically generated