Supero X10SL7-F Quick Reference Manual

S
UPERMICR
R
X10sL7-f
Q r g
uICk eferenCe uIde

Motherboard Layout and Features

VGA
LE5
LE6
BMC
BAR CODE
MAC CODE
SAS CODE
SPKR1
X10SL7-F
Rev. 1.01
BIOS
CPU1
Battery
PCH
JBT1
USB1 (3.0)
SAS
CTRL
L-SAS6 L-SAS7
L-SAS4 L-SAS5
L-SAS2 L-SAS3
L-SAS0 L-SAS1

CPU Installation

Heatsink Installation

Load Plate
Thermal Grease
Load Lever
North Center
Edge
Pin 1
South
Center Edge
CPU Properly
1. Push Down
Installed
2. Turn
Clockwise
to lock; Turn
Counter-
clockwise to
unlock
Load Lever Locked
into Place
Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this
C I
ontaCt nformatIon
• www.supermicro.com (Email: support@supermicro.com)
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
USB2/3
COM1
USB4/5
COM2
LAN2 LAN1
IPMI _LAN
LAN LAN
CTRL CTRL
IPMI CODE
CPU
JF1
LEDS2
LE3
JOH1

Front Panel Control (JF1)

Heatsink Fan
20 19
Ground
NMI
X
X
Vcc
Power LED
Vcc
HDD LED
NIC1 LED Vcc
NIC2 LED
Vcc
3. Connect Fan
Cables to onboard
OH/Fan Fail LED Vcc
Fan Headers
PWR Fail LED Vcc
Reset
Ground Reset Button
Power Button
Ground PWR
2 1
guide.

Jumpers, Connectors and LED Indicators

Jumpers
Jumper Description
JBT1
CMOS Clear
JI C1/JI C2
2 2
SMB to PCI-E Slots
JPG1
VGA Enable
JPL1/JPL2
LAN1/LAN2 Enable
JPME1
ME Recovery
JPME2
Manufacture Mode Select
JPS1
SAS Enable
JPUSB1
USB 4/5 Wake_up Enable
JWD1
Watch Dog Enable

Connectors

Connector Description
Battery
Onboard Battery
COM1/COM2
COM1 (Port)/COM2 (Header)
Fan1 - Fan4, FanA
System/CPU Fan Headers
JF1
Front Panel Control Header
JL1
Chassis Intrusion Header
JLED1
Power LED Indicator Header
JPI C1
2
Power SMB (System Management Bus)
JPW1
24-pin ATX Main Power Connector (Required)
JPW2
+12V 8-pin CPU power Connector (Required)
JSD1
SATA DOM (Device_On_Module) Power Connector
JSTBY1
Standby Power Header
JTPM1
Trusted Platform Module/Port 80 Connector
LAN1/LAN2
Gigabit (RJ45) Ports (LAN1/2)
IPMI_LAN
IPMI_Dedicated LAN
I-SATA0/I-SATA1
(Intel PCH) Serial ATA (SATA 3.0) Ports 0/1 (6Gb/sec)
I-SATA 2 - I-SATA5
(Intel PCH) Serial ATA (SATA 2.0) Ports 2~5 (3Gb/sec)
L-SAS 0-7
SAS Connectors 0-7 (supported by the LSI 2308 SAS controller)
(PCH) Slot 5
PCI-Express 2.0 x4 in x8 Slot
(CPU) Slot 6
PCI-Express 3.0 x8 in x16 Slot
SPKR1
Internal Speaker/Buzzer
SW1
UID (Unit Identifier) Switch
6-SGPIO 1/2
Serial_Link General Purpose I/O Headers 1/2 for SAS Connections
T-SGPIO 1/2
Serial_Link General Purpose I/O Headers 1/2 for SATA Connections
USB 2/3, 4/5
Backpanel USB 2.0 Ports 2/3, 4/5
USB 0,1 (3.0)
USB 3.0 Ports 0, 1 (USB 0: Type A Connector)
USB 8/9
Front Panel Accessible USB 2.0 Headers 8/9
VGA
Backpanel VGA Port

LED Indicators

LED Description Color/State Status
LE3 Standby Power LED On: Power On
LE4 UID LED Blue (On): Unit Identified
LE5 BMC Heartbeat LED Green (Blinking): BMC Normal
LE6 Power Status LED Red: PWR Fail/Yellow: Standby PWR Active/Green: PWR On Normal
LEDS2 SAS LED Green (Blinking): SAS Active/Red (Solid On): SAS Error
Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,
and LED indicators.
P C
aCkage ontents
• One (1) Supermicro Motherboard
• Six (6) SATA Cables
• One (1) I/O Shield
• One (1) Quick Reference Guide

Memory Support

The X10SL7-F supports up to 32GB of Unbuffered (UDIMM) DDR3 ECC
1600/1333 MHz in 4 memory slots. Populating these DIMM modules with a pair
Default
of memory modules of the same type and same size will result in interleaved
(See Chpt. 2)
memory, which will improve memory performance.
Pins 2-3 (Disabled)

Memory Population Guidelines

Pins 1-2 (Enabled)
Pins 1-2 (Enabled) Please follow the table below when populating the X10SL7-F.
Pins 1-2 (Normal)
DDR3 Unbuffered ECC (UDIMM) Memory
Pins 1-2 (Normal)
DIMM Slots per DIMMs Populat- DIMM Type
Channel ed per Channel
Pins 1-2 (Enabled)
2 1
Pins 1-2 (Enabled)
Pins 1-2 (Reset)
2 2

DIMM Memory Installation

Channel A Slot1
Channel A Slot2
Channel B Slot1
Channel B Slot2
Back Panel I/O Connectors
IPMI_LAN
USB 5 (2.0)
USB 3 (2.0)
COM1 USB 4 (2.0)
USB 2 (2.0)
Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
POR Speeds Ranks per DIMM (any
combination)
Unbuffered 1333, 1600 Single Rank, Dual Rank
DDR3
Unbuffered 1333, 1600 Single Rank, Dual Rank
DDR3
Towards the CPU
Towards the Edge of the Motherboard
Notches
Release Tabs
LAN1 LAN2 VGA