Vitek VT-EH Series Instructions Manual

4, 8, & 16 channel h.264 digital video recorders

Hide thumbs Also See for VT-EH Series:

Datasheet (2 pages)

Manual (62 pages)

Quick installation manual (2 pages)

Table Of Contents

Table of Contents

Quick Links

Digital Video Recorders

Table of Contents

Summary of Contents for Vitek VT-EH Series

Page 1: Digital Video Recorders
VT-EH Series 4, 8, & 16 Channel H.264 Digital Video Recorders • 4, 8, or 16 Video Inputs with 1 Main, 1 Spot Monitor Output and 1 DVI output (VGA compatible with included adaptor) • H.264 Compression • Supports both Dynamic and Static IP Addresses •...
Page 2: Important Safety Instructions
VT-EH Series DVRs________________________________________________________________________________ 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions.
Page 3 VT-EH Series DVRs________________________________________________________________________________ ● Installation should only be carried out by qualified personnel and in accordance with up-to-date electrical regulations. ● The DVR must be placed on a stable surface or mounted in an approved cabinet. Adequate ventilation must be provided, taking particular care not to block any of the air vents on the DVR.
Page 4: Main Features
VT-EH Series DVRs________________________________________________________________________________ MOUSE CONTROL Designed to be easily controlled with a mouse. ENHANCED GRAPHICAL USER INTERFACE [GUI] The DVR menu structure and on screen display is presented in a simple to use and logical GUI format. GENUINE PENTAPLEX OPERATION The DVR will continue to record at full frame rate during local playback, local setup, multi user remote viewing and playback and remote setup.
Page 5 VT-EH Series DVRs________________________________________________________________________________ TELEMETRY CONTROL Full telemetry control is available from the front panel or remote connection and a wide number of speed dome protocols are supported. Protocols can be set individually for each channel and telemetry speed can be adjusted to suit particular speed domes.
Page 6: S Y S T E M O R G A N I Z A T I On
VT-EH Series DVRs________________________________________________________________________________...
Page 7: System Configuration
VT-EH Series DVRs________________________________________________________________________________ 1. Front panel description DESCRIPTION Function Keys Turns unit On/Off POWER DISPLAY Selects various display modes in live display and playback SCR MODE Change display mode/Split mode SEARCH Displays the search menu MENU Displays the setup menus...
Page 8 VT-EH Series DVRs________________________________________________________________________________ 1. CAMERA INPUTS Connect up to 16 camera inputs. 2. MAIN MONITOR / SPOT MONITOR OUTPUTS Connect AV monitor instead of VGA output / One spot monitor can be connected. 3. AUDIO INPUTS & OUTPUTS Up to 4 audio inputs and one audio output can be connected.
Page 9 VT-EH Series DVRs________________________________________________________________________________ – – 3. Remote Controller description. POWER SETUP: Open System Setup Menu System ON/OFF Channel Selection Buttons ID Button AUDIO: Not Supported Select DVR ID ENTER: Apply / Select / Go to Next Screen RETURN Navigation Buttons:...
Page 10 VT-EH Series DVRs________________________________________________________________________________ & & • Connect up to 16 CAMERA INPUTS as necessary. • Connect monitors to the DVR using the COMPOSITE or DVI connections. • Connect power to the DVR. The DVR checks for proper power connection and emits two beeps.
Page 11: Menu Control
VT-EH Series DVRs________________________________________________________________________________ All menus can be controlled from the above ‗Status Bar‘ with the mouse or front buttons. DIVISION SCREEN Select the ‗DISPLAY‖ button for the screen division menu to appear. Select the screen type (1, 4, 6, 8, 9, 16 and rotation sequence).
Page 12 VT-EH Series DVRs________________________________________________________________________________ 1) CAM: Select the Channel. 2) Preset: Input preset numbers 1~255. Click SET to save current view (camera position) as a preset. Click GOTO to move the camera to a saved preset position. 3) Zoom, Focus, IRIS: User can control each item with + or - button.
Page 13 VT-EH Series DVRs________________________________________________________________________________ User can see the current log immediately. Click once after selecting log, recorded data will be played. This will appear if you select the ―PREVIEW‖ option. Panic Recording This menu is used to start and stop the Panic recording.
Page 14 VT-EH Series DVRs________________________________________________________________________________ Quick Menu User can use quick menu by right-clicking the mouse on each live channel. 1. Freeze On/Off: User can stop the live display of a channel that the user wants. Even though other channels show live display, this particular channel display is stopped.
Page 15 VT-EH Series DVRs________________________________________________________________________________ Click ―MENU‖ and click the SYSTEM SETUP menu. To navigate around any items in the setup menu, use the CURSOR KEYS and the ENTER and RETURN buttons. In general, the ENTER button is used to select and change a particular item and the RETURN button is used to cancel a change or exit from a particular setup screen.
Page 16: System Setup
VT-EH Series DVRs________________________________________________________________________________ CAMERA Click the CAMERA menu. CAMERA: CAMERA SETUP To setup the various camera options, highlight CAMERA and press ENTER. TITLE: Input the camera title. COVERT: When it is set to ON, the camera image is not displayed in live display but continues to record.
Page 17 VT-EH Series DVRs________________________________________________________________________________ Click each value with button. The selected channel is displayed in full screen. BRIGHTNESS, CONTRAST, TINT and COLOR can be changed as necessary. To modify a different channel, highlight CAMERA and choose the desired channel. Press RETURN when all changes are complete.
Page 18 VT-EH Series DVRs________________________________________________________________________________ Click the ―DETAIL‖ button and change the detail value with button. Note that some settings, such as AUTO FOCUS, may not be compatible with particular VITEK XPRESS PTZ equipment. If this is the case, changing the value will have no effect on PTZ control.
Page 19: Camera: Motion Sensor
VT-EH Series DVRs________________________________________________________________________________ CAMERA: MOTION SENSOR Click the MOTION SENSOR menu and click the value on the SENSITIVITY menu. Change the value with button. SENSITIVITY: Between 1 (Lowest) and 10 (Highest) and determines the degree of motion required before recording is activated.
Page 20: Display - Osd
VT-EH Series DVRs________________________________________________________________________________ DISPLAY To setup the various display options, highlight DISPLAY and press ENTER. DISPLAY - OSD Click the menu. Then click the button for ON/OFF and change the value. STATUS BAR: Determines the time to turn from the menu of status bar to time display.
Page 21: Display: Monitor
VT-EH Series DVRs________________________________________________________________________________ DISPLAY: MONITOR Click the MONITOR menu Then click the button for ON/OFF and to change the value. SEQUENCE DWELL: The time each screen is displayed in a sequence operation. SPOT DWELL: The time each screen is displayed on the spot monitor outputs.
Page 22: Sequence Display
VT-EH Series DVRs________________________________________________________________________________ SEQUENCE DISPLAY: Click the SEQUENCE menu. When the button is pressed, the default sequence will cycle through all channels, one by one. Sequence setup allows the operator to define a custom sequence, using mixed multi screen views and any desired channels.
Page 23 VT-EH Series DVRs________________________________________________________________________________ Press ADD. Then, ―Sequence Setup‖ menu appears. Determine the ―VIEW TYPE‖ and assign ―CONFIGURE‖. Then, click CONFIRM. To add an additional mode, click ADD. After finishing the setup, press CLOSE. To modify the current one, double click that mode. Then ‗Sequence Setup‖...
Page 24: Display: Spot-Out
VT-EH Series DVRs________________________________________________________________________________ DISPLAY: SPOT-OUT Click the SPOT-OUT menu and click the camera channel for ON/OFF. The DVR has 1 SPOT MONITOR OUTPUT. User can assign the SPOT OUT display for each channel. Double click the spot out channel that needs to be assigned.
Page 25: Sound: Audio
VT-EH Series DVRs________________________________________________________________________________ SOUND Click the SOUND menu. To setup the various sound options, highlight SOUND and press ENTER SOUND: AUDIO Click the AUDIO menu and click the ON/OFF menu. Then, click the button for ON/OFF. LIVE AUDIO: When it is set to ON, the selected audio channel can be monitored on the AUDIO OUTPUT.
Page 26 VT-EH Series DVRs________________________________________________________________________________ SYSTEM Click the SYSTEM menu. To setup the various system options, highlight SYSTEM and press ENTER. DATE / TIME Click the DATE / TIME menu. DATE & TIME: Allows the operator to set or modify the current date & time.
Page 27: System: System Management
VT-EH Series DVRs________________________________________________________________________________ SYSTEM: SYSTEM MANAGEMENT Click the SYSTEM MANAGEMENT menu. SYSTEM INFORMATION: User can see the system information as below. F/W version: Shows the firmware version of the DVR. H/W version: Shows the hardware version of the DVR. VIDEO SIGNAL TYPE: The DVR automatically switches between PAL and NTSC depending on the channel 1 input signal at power on.
Page 28: System: Control Device
VT-EH Series DVRs________________________________________________________________________________ SYSTEM NAME: It is used so that notification emails can be identified. F/W UPGRADE: Firmware updates may be released periodically to enhance system performance and add extra features. The operator can upgrade the firmware using a USB memory stick.
Page 29: User: User Management
VT-EH Series DVRs________________________________________________________________________________ USER Click the USER menu. To setup the various system options, highlight USER and press ENTER. USER: USER MANAGEMENT By default, the DVR is configured with a user ID of ADMIN, belonging to the ADMIN group and with a password of 1234.
Page 30: User: User Authority
VT-EH Series DVRs________________________________________________________________________________ USER ID: Edit the user ID using the virtual keyboard. PASSWORD: Change the password using the virtual keyboard. GROUP: Users can be assigned to one of three groups - ADMIN, MANAGER or USER. E-MAIL: Enter the user‘s email address if email notification is required.
Page 31: Network: Ip Setup
VT-EH Series DVRs________________________________________________________________________________ NETWORK Click the NETWORK menu and determine each value. NETWORK: IP SETUP Click the IP SETUP menu. DHCP: When enabled, the DVR will obtain an IP address automatically if it is connected to a DHCP server or router.
Page 32 VT-EH Series DVRs________________________________________________________________________________ HOW TO OBTAIN AN IP ADDRESS One of the easiest ways to obtain an IP address for your DVR is to use the built-in DHCP feature of your DVR. HOW TO SET UP DHCP The purpose of DHCP is to obtain all of the network information from the connected router. In most cases, the best way to do this is to cycle the DHCP feature which means turn it on, then off again.
Page 33: Network: Ddns
2) The Setup box will appear. Select “System Setup” 3) Select “Network” 4) Select “DDNS” 5) Make sure DDNS is turned “ON” 6) The user has the choice to use either the server provided by VITEK, Dvrlink.net, or an alternative server can be used— dyndns.org...
Page 34 VT-EH Series DVRs________________________________________________________________________________ DVRLINK.NET CONFIGURATION 1) Highlight DDNS Server, and change it to DVRLINK.NET 2) Highlight HOST NAME and press enter. The virtual keyboard will appear. Change the Host Name to your desired name by removing the previous entry--you can do this by repeatedly selecting the  key. (When choosing your host name, please don’t include any spaces or special characters).
Page 35: Remote Access
VT-EH Series DVRs________________________________________________________________________________ REMOTE ACCESS You can remotely access your VT-EH series DVR in the following ways: 1. The DVR’s MAC address 2. The DVR’s DDNS Host Name (by default this is set to the MAC address) 3. Your external static IP address (if you have one)
Page 36 VT-EH Series DVRs________________________________________________________________________________ REMOTE ACCESS DDNS Host Name The EH series allows you to name your DVR, and access it by that name. Steps to name your DVR 1. Access the DVR‘s main menu by using the remote control, or by using the buttons on the front of the unit.
Page 37 VT-EH Series DVRs________________________________________________________________________________ IP Address If you have a STATIC IP ADDRESS, you can use this to access your DVR. Accessing the DVR REMOTELY To access the DVR remotely via IP address, use the WAN IP address of the network the DVR is connected to. (Sometimes this IP...
Page 38: Network: E-Mail
VT-EH Series DVRs________________________________________________________________________________ NETWORK: E-MAIL Click the E-MAIL menu. SERVER: The SMTP outbound email server that should be used to send email notifications. PORT: The outbound email port number. SECURITY: Set to OFF if the SERVER does not require a username and password to connect.
Page 39: Event / Sensor: Hdd Event
VT-EH Series DVRs________________________________________________________________________________ EVENT / SENSOR Click the EVENT / SENSOR menu. To setup the various event handling options, highlight EVENT/SENSOR and press ENTER. EVENT / SENSOR: HDD EVENT Click the HDD EVENT menu. The DVR can monitor the hard drives and detect problems that may be developing.
Page 40: Event / Sensor: Alarm Output
VT-EH Series DVRs________________________________________________________________________________ EVENT / SENSOR: ALARM OUTPUT Click the ALARM OUTPUT menu and click each value. Determines the behavior and actions that will trigger each of the 8/16 alarm outputs. Behavior settings ALARM OUT: Choose which alarm output to configure.
Page 41: Event / Sensor: Buzzer Out
VT-EH Series DVRs________________________________________________________________________________ EVENT / SENSOR: BUZZER OUT Click the BUZZER OUTPUT menu and click each value. Determines the behavior and actions that will trigger the internal buzzer. Behavior settings OPERATION: The internal buzzer can be enabled or disabled. HDD EVENT: Determines whether a hard drive event sounds the buzzer.
Page 42: Event / Sensor: Email Notification
VT-EH Series DVRs________________________________________________________________________________ EVENT / SENSOR: EMAIL NOTIFICATION Click the EMAIL NOTIFICATION menu and click each value. Determines the behavior and actions that will send an email to a remote user. Behavior settings NOTIFICATION: Email notification can be turned ON or OFF.
Page 43: Disk Manage
VT-EH Series DVRs________________________________________________________________________________ DISK MANAGE Click the DISK MANAGEMENT menu. To manage the internal hard drives, highlight DISK MANAGE and press ENTER. RECORD TIME LIMIT: In certain circumstances, it may be necessary to limit the amount of footage stored on the DVR (to comply with data protection laws for example).
Page 44: Record Menu
VT-EH Series DVRs________________________________________________________________________________ RECORD MENU Click ―MENU‖. Input the password. Then main menu will appear. Click the RECORD SETUP menu. To setup the recording behavior of the DVR, highlight RECORD MENU and press ENTER. RECORD: RECORDING OPERATIONS Click the RECORDING OPERATION menu and click each value.
Page 45: Record: Continuous/Motion
VT-EH Series DVRs________________________________________________________________________________ RECORD: CONTINUOUS/MOTION Click the CONTINUOUS/MOTION SETUP menu. This setup screen allows the operator to configure scheduled and motion detection recording. There are 2 sections: SIZE/FPS/QUALITY: Recording settings for each channel can be defined across a 24 hour period, in blocks (for example between 09:00 and 18:00) or for each individual hour.
Page 46 VT-EH Series DVRs________________________________________________________________________________ Click the TIME BAR that user wants to have the values changed. Press ENTER to display the green cursor. The green cursor shown represents one hour. The table below the time bar shows the recording settings for this time period.
Page 47 VT-EH Series DVRs________________________________________________________________________________ Click the SIZE, FPS, QUALITY and AUDIO value. Then click the value with button to change. Press ENTER. Recording settings for the selected time period are displayed. SIZE: Recording resolutions of 352x240 (CIF), 704x240 (2CIF) or 704x480 (D1) NTSC can be selected for each channel.
Page 48 VT-EH Series DVRs________________________________________________________________________________ ACTIVATION Click the ACTIVATION menu. To change ACTIVATION settings, highlight CONTINUOUS/MOTION RECORDING and press ENTER. Use the CURSOR KEYS to highlight ACTIVATION and press ENTER. The schedule box is highlighted in green. Drag the Time and Channel with left mouse click.
Page 49: Record: Alarm Setup
VT-EH Series DVRs________________________________________________________________________________ RECORD: ALARM SETUP Click the ALARM RECORDING menu. The setup is the same as CONTINUOUS/MOTION RECORDING. This setup screen allows the operator to configure alarm input activated recording. SIZE/FPS/QUALITY: Recording settings for each channel can be defined across a 24 hour period, in blocks (for example between 09:00 and 18:00) or for each individual hour.
Page 50: Record: Panic Setup
VT-EH Series DVRs________________________________________________________________________________ RECORD: PANIC SETUP Click the PANIC RECORDING menu. Select the Size, Frame, Quality and Audio. During panic recording mode, the DVR will override all other recording settings and record continuously on all channels at the settings configured here.
Page 51: Search: Time Search
VT-EH Series DVRs________________________________________________________________________________ SEARCH To search for a particular section of recorded footage, press the SEARCH button. To protect unauthorized viewing of footage, only ADMIN and MANAGER user levels can playback footage. To login as ADMIN, enter the default password of 1234 and press ENTER.
Page 52 VT-EH Series DVRs________________________________________________________________________________ Drag the time bar with left mouse click. Press ENTER to select the calendar and use the CURSOR KEYS to move to the required day. As different days are selected, the timeline display also changes to show recorded footage on that day.
Page 53: Search Mode: Multi Playback
VT-EH Series DVRs________________________________________________________________________________ SEARCH MODE: PANO PANO (Thumb nail): Each Screen shows 3 hour data. CH1: 0~3 O‘clock CH2: 3~6 O‘clock CH8: 21~24 O‘clock User can select different channels and playback with faster speed of up to x64. SEARCH MODE: Multi Playback PLAY (Multi view): The default playback mode is of a 16 screen display.
Page 54 VT-EH Series DVRs________________________________________________________________________________ RESERVE: Press this to reserve current data. CONTINUE: Press this to reserve more data. Then display will return to playback. STOP: Make sure to press this button to reserve current data first. Then user can select RESERVE.
Page 55: Search: Event Search
VT-EH Series DVRs________________________________________________________________________________ SEARCH: EVENT SEARCH The DVR event log stores events such as motion and alarm activated recording, video loss, etc. To search for an event and playback the recorded footage, press the SEARCH button and log in as ADMIN with the default password of 1234.
Page 56: New Archiving
VT-EH Series DVRs________________________________________________________________________________ Playback resumes from the moment when the selected event occurred and continues until stopped by the operator. During event search playback, the playback buttons can be used as normal. To stop playback and return to live view mode, repeatedly press RETURN.
Page 57: Reserved Data Management
VT-EH Series DVRs________________________________________________________________________________ RESERVED DATA MANAGEMENT AVI ARCHIVING LIST: User can see the AVI archiving data that was reserved from new archiving menu or archiving of search. INFORMATION: The detailed information of Reserved AVI data. DELETE: User can delete the reserved AVI data...
Page 58: W E B C O N N E C T I O N S E T Up
VT-EH Series DVRs________________________________________________________________________________ FTP SETUP FTP Archiving is possible. User must set up the Host Name, Port number, User Name, and Password with the FTP server. FTP Archiving is possible on New Archiving or Reserved Data Management. DIRECTORY – Archived data will be saved to this user-defined folder on your FTP site.
Page 59: How To Connect
VT-EH Series DVRs________________________________________________________________________________ HOW TO CONNECT Input the IP Address or URL of the DVR in the Internet Explorer Address Bar. See pages 35-37 for more details. Default ID and password are ‗ADMIN‘ &‘1234‘ User needs to install Active-X, click Run Add-on Windows Internet Explorer In case user is unable to install active-X, User needs to check the option of activeX on IE security menu.
Page 60: Live Mode
VT-EH Series DVRs________________________________________________________________________________ Select Enable for all ActiveX related options. (Ex: Download signed ActiveX control, Download unsigned ActiveX control….) LIVE MODE...
Page 61 VT-EH Series DVRs________________________________________________________________________________ Explanation for function LIVE mode Select live division screen (1, 4, 8,9,16 split mode) Sequence mode Move to next camera Full screen Select live channel. – select a channel manually. Activate Mic to send a sound to DVR...
Page 62 VT-EH Series DVRs________________________________________________________________________________ • : Display all system logs with real time • : User is able to control connected PTZ camera. Pattern – move a camera among several preset positions Preset – set a position of camera view Swing – move a camera between two preset points...
Page 63: Search (By Time Line)
VT-EH Series DVRs________________________________________________________________________________ SEARCH (By time line) Select a time line on time table or set an exact time. Then press ‗Play‘ button 1. Refresh: Refresh the recording table of data. 2. Play: Start to display the recorded data from system.
Page 64: Search By Event
VT-EH Series DVRs________________________________________________________________________________ Backup 1. Select the desired Start and End Time 2. Select the desired channel(s) 3. Click Start. By default, the video will be saved to the C:\SaveFolder SEARCH (By Event) 1. Event: Select events for querying. 2. Period: Set duration for querying recording data.
Page 65: Setup Mode
VT-EH Series DVRs________________________________________________________________________________ SETUP MODE 1. CAMERA User can configure camera‘s attribute such as title, live color, PTZ setup or motion.  Motion setup for detecting motion events. 1) Select Motion menu tab. 2) Select a channel and sensitivity. 3) Drag a mouse on the image to select detecting area.
Page 66 VT-EH Series DVRs________________________________________________________________________________ 2. Display 1) OSD –Choose text to display over the image. 2) Monitor - User can set dwell time for sequence or spot, and pop up function.
Page 67 VT-EH Series DVRs________________________________________________________________________________ 3. Sound 1) Audio Setting – Select a live audio channel and activation 2) Buzzer setting – Activate buzzer out for event notification 4. System User can configure the DATE of the system. Check system information and set controller.
Page 68 VT-EH Series DVRs________________________________________________________________________________ 5. Recording User can configure the recording parameter. Setting detail is same as system. 6. User To add a User, select Add, then assign Authority level and Log Out time.
Page 69 VT-EH Series DVRs________________________________________________________________________________ 7. Network User can check the system‘s network information and selectable speed level. IP settings are not allowed to be changed on remote site. Network IP can only be changed from DVR. For email notification, user can input the SMTP server detail as shown below.
Page 70 VT-EH Series DVRs________________________________________________________________________________ 8. Sensor Management can set all device option of Alarm in/out, Buzzer out for event notification. (HDD EVENT, Alarm Input, Alarm output, Buzzer out, E-mail notification option) All detail setup follow DVR system setup INFORMATION Display Model name of DVR and WEB Remote Software version.
Page 71: B A C K U P P L A Y Er
VT-EH Series DVRs________________________________________________________________________________ To view archives backed up from a DVR, double click BackupPlayer (located in the Player folder). NOTE: When archiving from the web browser to a PC, the BackupPlayer is NOT included. To obtain the BackupPlayer, user must physically archive from the DVR to a USB flash drive.
Page 72 VT-EH Series DVRs________________________________________________________________________________ 2. Click the [Open file] button and open the backup file. 3. After opening file, select ―Yes‖ to check the watermark. 4. If the backuped AVI file is modified, [Verification failed] message will appear.
Page 73: S M A R T P H O N E C O N N E C T I On
VT-EH Series DVRs________________________________________________________________________________ iPHONE 1. Select the Safari browser. 2. Enter the IP address or URL to connect. And Click the [GO] button. 3. Enter the User name and Password then use can see the Image. (Default: ADMIN / 1234)
Page 74 VT-EH Series DVRs________________________________________________________________________________ BlackBerry 1. Select the Web browser. 2. Enter the IP address or URL to connect. And press the Enter button. 3. Enter the User name and Password then use can see the Image. (Default: ADMIN / 1234)
Page 75 ‘DVR Viewer’ Guide (iPhone / iPad / Android) 1.1 – Install & Connect (iPhone & iPad) 5. Insert IP and ports then save 1. Search and Install ―Vitek DVR Viewer‖ in Apple APPstore 6. Insert ID, Password and login type select...
Page 76 VT-EH Series DVRs________________________________________________________________________________ 1.2 – Install & Connect (Android) 1. Search and Install ―Vitek EH DVR Viewer‖ in 4. Insert name, URL, ports, ID, Password and select ID/Password save type then select ‗Save‘ button Android market **** -> 2. Run ‗Vitek EH DVR Viewer‘ Application 5.
Page 77 VT-EH Series DVRs________________________________________________________________________________ 2 – PTZ & Snapshot (PRO version) 3 – Log View (PRO version) 1. Touch the ‗PTZ‘ button 1. Touch the ‗log view‘ button 2. Set PTZ by pressing ‗+/-/∧/∨/</>‘ button. 2. Select start/end time and Filter Option select after touch ‗search‘...
Page 78 VT-EH Series DVRs________________________________________________________________________________ 4 – Search (PRO version) 5 – Setup (PRO version) 1. Touch the ‗Search‘ button 1. Touch the ‗Setup‘ button 2. Select date/time and touch play button 2. WebRA setup menu and the same settings are available.
Page 80 (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is non- transferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller.
Page 81 28492 CONSTELLATION ROAD VALENCIA, CA 91355 WWW.VITEKCCTV.COM | 888-VITEK-70...

Vitek VT-EH Series Instructions Manual

Quick Links

Digital Video Recorders

Related Manuals for Vitek VT-EH Series

Summary of Contents for Vitek VT-EH Series

Table of Contents