Page 1
The Bowflex Xtreme 2 SE ® Home Gym Assembly Manual 001-7033-040111.D...
Page 3
. Before assembling your Bowflex Xtreme® 2 SE home gym please read the Assembly Manual and follow the Important Safety Precautions . For information on how to use your Bowflex Xtreme® 2 SE home gym, refer to the Bowflex Xtreme® 2 SE Owner’s Manual .
Read and understand the complete Owner’s Manual supplied with this machine before first use. Keep the Owner’s and Assembly Manuals for future reference . • Do all assembly steps in the sequence given. Incorrect assembly can lead to injury. Bowflex Xtreme 2 SE Assembly Manual ®...
Before Assembly Please take the time to read all assembly instructions Basic Assembly Principles before attempting to assemble your Bowflex Xtreme ® 2 SE home gym. Select where you are going to locate Here are a few basic tips that will make your assembly of your machine carefully.
Page 7
Parts Reference Guide 32 39 NOTE: CABLES ARE NOT SHOWN FOR CLARITY Bowflex Xtreme 2 SE Assembly Manual ®...
Page 8
PULLEY SLIDER, 4” w/o DECAL PULLEY, PAIR FLOATING LAT DBL PULLEY / HOUSING PULLEY SLIDER, 4” w/ DECAL LEG EXTENSION BACKBONE LEG EXTENSION PIN TUBE, FOAM ROLLER PAD, FOAM ROLLER END CAP 3/4” Bowflex Xtreme 2 SE Assembly Manual ®...
Hardware Guide Tools you will need: You will need the tools listed below to complete the assembly of your Bowflex Xtreme 2 SE home gym . If ® you don’t have these tools, you can find them at any hardware or department store .
Rod Box into Lower Lat Tower Frame . Fasten the Rod Box to the Rod Box w/ Rods Lower Lat Tower Frame with screws and washers as shown . Flat Washers Tighten screws until snug. Self Threading Screws Bowflex Xtreme 2 SE Assembly Manual ®...
Page 11
. Slide the top of the Seat Support Rail onto the Lower Lat Tower Assembly connector as shown . Secure using screws and washers as shown . finger tighten screws at this time. Bowflex Xtreme 2 SE Assembly Manual ®...
Page 12
Frame Rail as shown in Detail 5b . Slider Pulley Screw Repeat Steps 5-3 through 5-5 for the Right Flat Washer Squat Pulley Frame. Button Head Screw Left Squat Frame Flat Washer Connector Detail 5b Left Frame Rail Bowflex Xtreme 2 SE Assembly Manual ®...
Page 13
• Main Assembly Slider Pulley w/ Cable Assembly tools: 3/16 Hex Wrench 7-1 Install a Slider Pulley onto each Pulley Arm as shown . 7-2 Choose any of the four holes to secure . Bowflex Xtreme 2 SE Assembly Manual ®...
Page 14
. A rubber mallet may be needed to secure the end caps . note: The Leg Extension may be adjusted Lock Knob during workout to best suit your height and personal preferences . Bowflex Xtreme 2 SE Assembly Manual ®...
Page 15
Seat Support Rail . Seat Support Rail 11-2 Secure Seat Back Pad to the Seat Support Rail using screws and washers as shown . Bowflex Xtreme 2 SE Assembly Manual ®...
Page 16
Seat Support Rail as shown in Figure 12b . note: Reverse procedure to remove seat . Seat Backbone Detail 12a Seat Support Rail Detail 12b - Back View Seat Locking Pin installed Bowflex Xtreme 2 SE Assembly Manual ®...
Page 17
Ab Bracket • 2 Nylock Nuts 3/8 -16 tool: 7/32" Hex Wrench Lock Nut 14-1 Attach the Ab Cross Bar to the Ab Crunch Bracket as shown. Tighten all hardware. from this step . Bowflex Xtreme 2 SE Assembly Manual ®...
Page 18
Figure 15b . Ab Bracket on Lat Tower do not tighten hardware at this time. Lat Pulley Housing Flat Washer Washer Button Head Screw Long Bolt Bowflex Xtreme 2 SE Assembly Manual ®...
16 Cable and Pulley Routing – Overview The figure below shows all Pulleys on the Bowflex Xtreme 2 SE home gym. Subsequent images show how to connect and route each of the Cables through the Pulleys. (The Ab Crunch Station is not shown for clarity.) Connecting the Cables is much easier with a second persn assisting you .
Page 20
Figure 20 and holding the cable tightly where indicated . 17-3 Repeat for the Left Pulley Cable (on the Left Frame Rail), without loosening your grip on the Right Pulley Cable. Bowflex Xtreme 2 SE Assembly Manual ®...
Page 21
You will probably need to push the Power Rod unit out of the way for this step. The Power Rod unit is ® ® not pictured for the sake of clarity. Bowflex Xtreme 2 SE Assembly Manual ®...
Page 22
Pulleys . See Figure 19b . note: The Cable End Stop Ball Core should fit over the Ferrue when installed correctly . Rotate the Core to align it with the groove in the Ball . Bowflex Xtreme 2 SE Assembly Manual ®...
Page 23
Once the Cable End Stop Balls are attached, hook each Rod Hook onto the Lat Pulley Housing as shown in Figure 19d . Figure 19d - Rod Hooks Storage on Lat Pulley Housing Bowflex Xtreme 2 SE Assembly Manual ®...
Page 24
Continue to guide the Cable down through the Inner Right Frame Rail Pulley (9), up through the Right Pulley Arm Pulley (10), as shown in Figure 20 . Finally, insert the Cable End through the Cable End Stop Ball and attach the Cable Core, as completed during Step 19 . Bowflex Xtreme 2 SE Assembly Manual ®...
Page 25
Assembly Guide step 20b Cable and Pulley Routing – Connect Left Squat Cable through the Floating and Main Assembly Pulleys Repeat the same procedure completed during Step 20 for the Left Squat Cable. Bowflex Xtreme 2 SE Assembly Manual ®...
Page 26
Inspection Please inspect your machine to ensure that all fasteners are tight and components are properly assembled . Review all warnings affixed to machine . Congratulations! You have successfully completed assembly of your Bowflex Xtreme 2 SE home gym! ®...
Need help?
Do you have a question about the Xtreme 2 SE and is the answer not in the manual?
Questions and answers