Nautilus, Inc., www.NautilusInc.com, 5415 Centerpoint Parkway, Groveport, OH 43125 U.S.A. - Customer Service: North America (800) 605-3369, csnls@nautilus.com | outside U.S. www.nautilusinternational.com |

Printed in China | © 2020 Nautilus, Inc. | Bowflex, the B logo and SelectTech are trademarks owned by or licensed to Nautilus, Inc., which are registered or otherwise protected by common law in the United States

and other countries. | ORIGINAL DOCUMENT - ENGLISH VERSION ONLY

8027822.081520.A

Bowflex

™

Page Number

SelectTech

2080 Barbell with Curlbar

™

Service Manual

8027821.081520.A

Table of Contents

Summary of Contents for Bowflex SelectTech 2080

Page 1: Table Of Contents
Bowflex SelectTech 2080 Barbell with Curlbar ™ ™ Service Manual Service Manual ™ ™ 8027821.081520.A Table of Contents Section Code Section Page Number Important Safety Instructions Safety Warning Labels and Serial Number Specifications Moving the Equipment Leveling the Base Maintenance...
Page 2: Important Safety Instructions
Important Safety Instructions and General Troubleshooting Service Procedures Information for the Bowflex SelectTech ™ ™ ™ ™ 8027823.081520.A 2080 Barbell with Curlbar NOTICE: This document provides important safety instructions, adjustments, and general troubleshooting information for the maintenance of the Bowflex SelectTech 2080 ™ ™ Barbell with Curlbar. If you need assistance, please contact Customer Service (if purchased in US/Canada) or your local distributor (if purchased outside US/Canada).
Page 3: Safety Warning Labels And Serial Number
SAFETY WARNING LABELS AND SERIAL NUMBER Record serial number in the Serial Number field at the beginning of this manual. WARNING Do Not Drop • This product is for Home use only. (Statement is available • Not intended for use by anyone under in English only.) 14 years of age. • Consult a physician prior to using any exercise equipment.
Page 4: Moving The Equipment
If at any time the Warning labels become loose, unreadable or dislodged, replace the labels. If purchased in US/Canada, contact Customer Service for replacement labels. If purchased outside US/Canada, contact your local distributor for them. The Bowflex SelectTech Barbell is a very low maintenance product. However, there are steps that you should take to keep the product ™...
Page 5: Maintenance Parts
Maintenance Parts Front Back Item Description Item Description Base Tube, Front Adjustment knob (selection knob) Base Tube, Rear Weight selection housing Base Plates Locking tab, plate Levelers Selection lip (pocket) Base End Shrouds Locking tab, base Barbell Handle Assembly Lock pin actuator, base Curl Bar Handle Assembly Adapter Plates 5-lb (2.27 kg) Weight Plates...
Page 6: Troubleshooting
TROUBLESHOOTING Problem Solution Barbell handle does not fully insert 1. Make certain that both adjustment knobs are set directly to the number 20. into base when no plates are 2. Ensure that base spacing is set correctly per step 6 of the assembly instructions. selected (handle has no plates 3.
Page 7: Testing The Locking Mechanism
Understanding and testing the locking mechanism function The Bowflex SelectTech Barbell features an exclusive locking mechanism designed to ensure proper and complete selection of the weight plates ™ ™ as well as to ensure weight plate retention during the workout. Fully understand the function of this mechanism and do tests of the mechanism regularly to make sure it operates correctly.
Page 8: Replacement Procedure Skill Level
Replacement Procedure Skill Level Level I : Low - very little mechanical knowledge or exposure. Level II : Intermediate - some experience with mechanical procedures. Level III : Advanced - knowledgeable about mechanical procedures. When disposing of old parts, obey the applicable local and provincial requirements. For instructions to replace the following parts, please refer to the Assembly Manual for your machine: •...
Page 9: Align The Base
2080 Barbell with Curlbar ™ ™ Skill Level: I 8027672.081520.A NOTICE: This document provides instructions on how to properly align the Base and Weight Plates on the Bowflex™ SelectTech™ 2080 Barbell with Curlbar. If you need assistance, please call Nautilus Customer Service (if purchased in US/Canada) or your local distributor (if purchased out- side US/Canada). To find your local distributor, go to: www.nautilusinternational.com This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Page 10 Note: Your machine may not match the images provided exactly. Do not drop the barbell/curl bar or weight plates. Dropping the barbell/curl bar or weight plates will damage the weight plates and/or the locking mechanism, and can cause the weight plates to disengage (drop) from the handle without warning. This can cause serious injury, and will void the warranty.
Page 11 Ensure the locking tabs of the Shroud bracket are seated inside the pockets (selection lip) of the back Weight Plate (Figure 2b). The plate surfaces should be parallel, and lean on the Shroud bracket and base. Figure 2b Plates correctly aligned Plates misaligned 3.
Page 12 6. Remove the Barbell from the Base. There should be 2 Weight Plates lifted on each side of the Barbell. If the Barbell picks up more than 2 Weight Plates on each side, do not use the Barbell. Contact Bowflex Customer Service or your local distributor for a replacement Barbell handle assembly.
Page 13: Replace The Selection Knob And Housing
Skill Level: II Bowflex SelectTech 2080 Barbell/Curlbar ™ ™ ™ ™ 8027824.081520.A NOTICE: This document provides instructions for the replacement of the Selection Knob (Adjustment Knob) and Housing on the Bowflex SelectTech 2080 Barbell with ™ ™ Curlbar. If you need assistance, please call Bowflex Customer Service(if purchased in US/Canada) or your local distributor (if purchased out- side US/Canada).
Page 14 Some components of the machine can be heavy or awkward. Use a second person when doing the assembly steps involving these parts. Do not do steps that involve heavy lifting or awkward movements on your own. Note: Your machine may not match the images provided exactly. Turn both Adjustment Knobs to the number 20. Remove the barbell assembly from the base and set it carefully on the floor.
Page 15 4. Using a 3 mm hex wrench, loosen and remove the hardware (indicated by arrows) that attaches the Barbell Handle to the Selection Housing. Set the hardware safely aside for reassembly. 3 mm Slide the old Selection Housing assembly out of the Barbell Handle tube and discard. Note: This step may require two people. Installation is the reverse procedure.

Bowflex SelectTech 2080 Service Manual

Quick Links

Table of Contents

Related Manuals for Bowflex SelectTech 2080

Summary of Contents for Bowflex SelectTech 2080

Table of Contents