Cisco TelePresence Server 7010 Installation Manual
Hide thumbs
Also See for TelePresence Server 7010:
- Installation manual (204 pages) ,
- Product user manual (151 pages) ,
- Help manual (132 pages)
Related Manuals for Cisco TelePresence Server 7010
Summary of Contents for Cisco TelePresence Server 7010
-
Page 1: Installation Guide
Cisco TelePresence TelePresence Server 7010 Installation Guide 61-0028-06 August 2013 Cisco TelePresence Server 7010 Installation Guide Page 1 of 14... -
Page 2: Table Of Contents
Contents General information About the Cisco TelePresence Server 7010 Package contents Port and LED locations LED behavior Front panel LED behavior Rear panel LED behavior Connecting the TelePresence Server Before you start Task 1: Connect power Task 2: Connect to Ethernet Port A... -
Page 3: General Information
General information General information About the Cisco TelePresence Server 7010 The Cisco TelePresence Server 7010 (TelePresence Server) is a technologically advanced media processor, combining continuous presence high definition video conferencing and the highest possible voice quality. Package contents The following items are included with the TelePresence Server. Verify that you have these items before... -
Page 4: Led Behavior
Power supply LED behavior Front panel LED behavior The following table describes the behavior of the LEDs on the front of the TelePresence Server. Table 1: TelePresence Server 7010 front panel LED behavior Color Indicates Status Green The unit is operating normally... - Page 5 The link is operating at 100Mbps. This LED flashes to indicate activity 1000 Green The link is operating at 1000Mbps. This LED flashes to indicate activity Admin Port Activity Reserved for future expansion Link Connectors Reserved for future expansion Cisco TelePresence Server 7010 Installation Guide Page 5 of 14...
-
Page 6: Connecting The Telepresence Server
Server. Do not connect to these ports unless the web interface allows you to configure them. Do not connect multiple ports to the same subnet unless instructed to do so by the web interface. Cisco TelePresence Server 7010 Installation Guide Page 6 of 14... -
Page 7: Configuring The Telepresence Server
To assign a static IPv4 address to Port A, use the following command: static A <IP address> <netmask> [<default gateway address>] Note: If you do not have a DNS server, use 0.0.0.0 as the DNS server IP address. Cisco TelePresence Server 7010 Installation Guide Page 7 of 14... -
Page 8: Task 6: Discover The Ip Address Of The Telepresence Server
Note: We recommend that you change the admin account to use a password as soon as possible. To do that, go to Configuration > Change password and type in the new password twice. Cisco TelePresence Server 7010 Installation Guide Page 8 of 14... -
Page 9: Configuring The Telepresence Server Software
Task 8: Configure settings, conferences, and endpoints You may need to configure the network and system settings, then go on to add conferences and endpoints. Refer to the online help for assistance. Cisco TelePresence Server 7010 Installation Guide Page 9 of 14... -
Page 10: Checking For Updates
Checking for updates Checking for updates It is a good idea to regularly check the Cisco web site for updates to the device's main software. This section describes how to upgrade the device using the web interface. To check for, and download, updates: 1. -
Page 11: Replacing The Power Supply
Replacing the power supply CAUTION: Only replace the power supply under the guidance of Cisco customer support. The power supply will be installed when you receive your TelePresence Server. To replace the power supply: 1. Remove the power cable from the unit to disconnect the power. -
Page 12: Troubleshooting And Technical Support Information
Your contact email address or telephone number. A full description of the problem. To view a list of Cisco TelePresence products that are no longer being sold and might not be supported, visit http://www.cisco.com/en/US/products/prod_end_of_life.html and scroll down to the TelePresence section. -
Page 13: Technical Specifications
Optimum operating environment 21°C to 23°C 45% to 50% (non-condensing) Anti-static precautions When servicing or removing components or connections, first attach an anti-static wrist strap to an appropriate earth point. Cisco TelePresence Server 7010 Installation Guide Page 13 of 14... - Page 14 MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners.