Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Genie GCG350L
Summary of Contents for Genie GCG350L
- Page 2 Check your ceiling where the power You need a 110-120 Volt power supply available. The outlet should be no more than 3 head of your new unit will be mounted. Plan how you will be mounting the power head. feet from the power head once it is mounted. (The It is possible that ceiling joists...
-
Page 3: Door Installation
® TYPICAL SUPPORT BRACKET ADDED HEADER BRACKET MOUNTING BOARD BRACES 48" POWER 120V GROUNDED OUTLET EXTENSION TORSION SPRING' ® SECTmONAL DOOR I-PmECE DOOR... - Page 4 INTELLICODE ® Roiling Code Security System. SECTION ......... PAGE An electronic rolling code system that enhances the security of the door operator by continuously changing the access code PRE-INSTALLATION CHECKS ......each time the remote control is used. The door operator OPERATORFEATURES .........
- Page 5 Ratchet Pencil Carpenter's level Adjustable wrench Drill © 5/32" Drill Bit 7/16"and 9/16" Tape measure Phillipsscrewdriver Wire strippers Sockets Step ladder ,&WARNING #6 x 1-1t4" Pan (32) Single-button Multi-button Head Phillips Entrapment Warning Screw Wall console remote control remote control Label Safety Brochure #10-16 x 1-1t4"...
- Page 7 ItemPartName Number R equired Power Head Assembly 1 pc,rail 3 pc,rail Power head assembly (box) Rail a ssembly (1-piece#box) Rail ( 1-piece)(box) Rail a ssembly (3-piece)(items 5,6,7)(box) First r ail s ection (box) Middle r ailsection ( box) End railsection ( box) Rail c lamp ( blue bag) 1/4"-20 x 5/8"...
-
Page 8: Rail Assembly
Middle 1. Identify the rai! sections (Fig. 1-1). • First rail section (attaches to power head). - 2 holes each end. - Half-circle notch 1 end. - Motor end has no notch. • Middle rail section. - 2 holes & half-circle notch each end. •... - Page 9 5. Slip carriage into carriage slot of rail. • Flip the rail assembly up side down. • Place emergency release lever in "release" position (See below). - Check arrow on the side of carriage points toward door end of rail. - Slide carriage into rail at power head end (Fig.
- Page 10 Attach limit switches. 2 switches included, "CLOSE" limit switch (brown wire) and "OPEN" limit switch (white wire) (Fig. 1-10). • Turn set screws (39) into threaded holes, just enough so screw stays in place. (Fig. 1-10). [39]#8_32 xi,, Point arrow on top "CLOSE" limit switch toward door end of rail.
- Page 11 5. Do Not connect the operator to the source of power until instructed to do so. OPERATION INSTRUCTIONS. If you have questions or do not understand an instruction, call The Genie 6. Locate the control button: Company or an authorized Genie Dealer.
- Page 12 NO7_iF; f he_-_oq;)b;"scke ocs_Fo_*_needs o be _;_bove hesde;' fb;' !is_'_!_!_i'e ch::_o openh, W you £;,oud seco_,e@ _sched i'@s_one;'s no h_c/ @d} _;_c;'oss w_d/suo%; o_ eF he, sM_, of;/o mu£ £_ s f?Ycien (Fig. 2-4) 2. Mounting the header bracket. seye_x,_ w_ys, mehod _ I M pmM_,"_d f_ poss b _ bec_se of _d@d s_,ng_h...
- Page 13 1. Getting Started. • Position rail/power h eadassembly (Fig.2-7). - Rail s trapleaning onwallnexttoheaderbracket. -Place material o n floorunderpowerheadto protect f romscratching. ( Abox,stool,or similar devicemaybe needed to cleara torsion spring,as shown.) 2, Mountingthe assembly. • Attachrail strapto headerbracket u singnut (47) (Fig.2-7inset).
- Page 14 OPEH YELLOW RTS BAG 1. Attach the arms. • Fasten curved door arm to door bracket using clevis pin (24) and cotter pin (25) (Fig. 2-10). • Straight arm to carriage using clevis pin (24) and cotter pin (25) (Fig. 2-10). [24] [25] 2.
- Page 15 h_O_TE"%h..1. Mounting brackets. • Mark both sides of garage door frame or wall 5" above floor. (Fig. 3-1). • Hold bracket against door frame or wall. - Check if brackets extend out from wall far enough, so tongue of bracket is beyond door, tracks or any door hardware.
- Page 16 3. Wiring (cont'). • Securely fasten wires to wall as you go. -Use insulated staples (included). [30] -Staples should be snug only. • Make wire attachments at "STB's." -Splitting and stripping wire ends to be connected as shown (Fig. 3-6). -Loosen terminal screws.
-
Page 17: Wall Control Installation
1. Finding the mounting location. • Pick a convenient location for mounting wall control. -Location you choose should be in direct sight of door. -It should be at least 5' above floor to prevent small children from operating door. must be away from any moving parts. (You should not be able to reach the door while standing at wall control.) 2. - Page 18 1. Plug the operator into a properly grounded electrical outlet. 2. Check Safe-T-Beam® alignment (Fig. 6-3). 1. instructions for electrician. • Remove power from circuit. • Remove motor cover (Fig. 6-1). -Removing hex head screw located in center on bottom of cover. -Slide cover down and off.
-
Page 19: Limit Switch/Force Adjustment
NO'}q_:;: ©u_<;g open_}_®_" cl,,,c hW hhy fouc'® ,fsm en< _he _' o_oY p<o_x,:<_c_o_ may shu of 7 p®we_ °_o he ope_s_ ®s # _hh}soccu_,_, wv}_F_hou 20 _'ffmAes _o _/;ow _he motoJ," pm_ec_o_ _o mseL 1. Adjusting limit switches, • Locate force control knobs on power head (Fig, 7-1). -
Page 20: Programming Remote Controls
The force adjustments and limit switch settings MUST BE COMPLETED before testing contact reverse. 1. Testing. • Open garage door using wall control. - Place a 2" x 4" board (laid flat) under center of garage door opening (Fig. 7-5). -Close door using wall control. -
Page 21: Remote Control Battery Replacement
1. Programming. • Foreachbutton. -Program eachbuttonseparately. - Followsinglebuttonremoteprocedure (previous page)for eachbutton. 2. Operating. • Sameas singlebuttonremote. 1. Clearmemory. • Pressandholdlearncodebutton power head) for 10 seconds or until Indicator LED goes out. • Program remaining or new remote controls as done previously. Your door operator will no longer recognize any signal received from the... -
Page 22: Maintenance
Use This Guide To Correct Problems With Door Operator. manually if springs are broken. If These Solutions Do Not Work, - CONTACT A PROFESSIONAL FOR SERVICE, Call Customer Service at 1.800.35.GENIE 2. Door balance. • Close the door. • Pull emergency release knob down to release SOURCE SENSOR... - Page 23 Door starts up, • Be suredoor,operator,and springsare in but stops before good repair,properlylubricated and balanced Usewall controlsuppliedwithoperator. A ny otherwall controlcan cause it's completely (See maintenance section). the operatorto operateunexpectedly and lightnot to work. open. • Check"OPEN"limit switchsetting (See sectionm). •...
-
Page 24: Compliance Statement
TRANSMITTER COMPLIANCE STATEMENT Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture. No warranty is made that they comply with all legal requirements of any other jurisdiction. If transmitters are to be used in another country, the importer must determine compliance with any local laws and regulations... - Page 25 Prix sur oppose Accessoires pour ouvre-porte de garage AVAILABLE AT YOUR LOCAL GENIE ¢ DISTRIBUTOR (GIT-1) 1-ButtonRemote ControlwithIntellicode®. - Allows remote operation o fonegarage door. Controlador r emotode uricbotchcon Intellicode®.- Proporcionar operacion r emoto deunopuerta delgaraje. Telecommande de un boutonavecIntellicode®.
- Page 26 SHiPORDERTO: ADDRESS / DIRECCI6N / ADRESSE MAIL ORDER ENVIARMERCANCIA FORM TO: CON: CITY / ClUDAD /VILLE The Genie Company EXPCDIER MARCHANDISE 22790 Lake Park Blvd. POUR: STATE / ESTADO / eTAT ZIP / CoDIGO POSTAL / CODE POSTAL Alliance, Ohio 44601...
-
Page 27: Limited Warranty
Some statesand provincesdo not allow limitationson how long an implied warranty lasts or the exclusion of incidentalor consequential damages,so the This warranty is the only one we will give on your Genie product, and it sets above exclusions may not apply to you.