Craftmade VG54TI2 Installation Manual

Hide thumbs

Table of Contents

Quick Links

Federal regulations require ceiling fans

with light kits manufactured or imported

after January 1, 2009, to limit total

wattage consumed by the light kit to

190W.

Therefore, this fan is equipped

with a wattage limiting device.

Installation Guide

For Models:

VG54TI2

VG54FB2

E206035

net weight of fan: 17.70 lb (8.03 kg)

READ THESE INSTRUCTIONS AND

AND SAVE THEM FOR FUTURE USE

Need help?

Do you have a question about the VG54TI2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Craftmade VG54TI2

Page 1: Table Of Contents
190W. Therefore, this fan is equipped with a wattage limiting device. Installation Guide For Models: VG54TI2 Table of Contents: Safety Tips. pg. 1 VG54FB2 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation.
Page 2: Safety Tips
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS.
Page 3: Unpacking Your Fan
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs.
Page 4: Installation Preparation
3. Installation Preparation. blade edge To prevent personal injury and damage, ensure inches 7 feet that the hanging location allows the blades a (2.13 m) (76 cm) clearance of 7 feet (2.13 m) from the floor and 30 in (76 cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square 12 ft.
Page 5: Fan Assembly. Pgs
5. Fan Assembly If you wish to extend the hanging length of your fan, you must remove the hanging ball from the 16-inch set screw hole set screw downrod provided to use with an extended downrod stop pin (sold separately). [If you wish to use the 16-inch downrod, please proceed to instructions following the dotted line below.] hanging ball...
Page 6 5. Fan Assembly. (cont.) safety cable loop With the hanging bracket secured to the outlet wood box and able to support the fan, you are now ceiling joist ready to hang your fan. Grab the fan firmly wood screw with two hands. Slide downrod through and washer opening in hanging bracket and let hanging ball rest on the hanging bracket.
Page 7: Wiring
6. Wiring ground (green CAUTION: Be sure outlet box is properly grounded or bare) white supply wire and that a ground wire (GREEN or Bare) is present. black supply wire Make sure all electrical connections comply with Local Codes or Ordinances and the National ground (green Electrical Code.
Page 8: Canopy Assembly
antenna 7. Canopy Assembly. hanging bracket Raise canopy to hanging bracket and align slotted holes in canopy with loosened screws in hanging bracket. Twist canopy to lock. Re-insert screws that were previously removed (on page 3, Section 4) and secure all screws with Phillips screwdriver.
Page 9: Light Assembly (Optional)
9. Light Assembly (Optional). If you wish to use your fan WITH the light kit, install motor housing the halogen bulb, type JD E11, 50 watts max., provided. Tip: Do not touch glass portion of bulb with fingers or hands. Oil from skin can cause bulb to overheat and go out prematurely.
Page 10: Automated Learning Process./Activating Code
10. Automated Learning Process./Activating Code. CAUTION: The remote control transmitter can be transmitter code (back) programmed to multiple receivers or fans. If this is switches not desired, turn wall switch off to any other programmable receiver or fan. Remove battery cover on back side of remote control transmitter.
Page 11: Remote Control Operation
12. Remote Control Operation. HI button - turns fan to HIGH speed MED button - turns fan to MEDIUM speed LOW button - turns fan to LOW speed button - turns fan OFF button - pushing button turns light ON/OFF; pressing button and holding it down for more than 0.7 seconds converts it into a dimmer...
Page 12: Troubleshooting
Return fan, shipping prepaid, to transmitter and wall control are set properly. Craftmade/Ellington. We will repair or ship you a 3. Verify that receiver is wired properly. replacement fan, and we will pay the return shipping cost.

This manual is also suitable for:

Vg54fb2