Craftmade VEN52 Installation Manual
  1. Manuals
  2. Brands
  3. Craftmade Manuals
  4. Fan
  5. VEN52
  6. Installation manual

Craftmade VEN52 Installation Manual

Hide thumbs Also See for VEN52:
Table of Contents

Advertisement

Quick Links

Download this manual
Ventura
Installation Guide
For Model:
VEN52
WARNING:
DC Motor will not
operate until blades
are installed
APPROVED FOR USE IN
DAMP LOCATIONS
net weight of fan: xx.08 lb (7.75 kg)
READ THESE INSTRUCTIONS AND
SAVE THEM FOR FUTURE USE

Table of Contents:

Wiring. pg. 6
Warranty. pg. 12
PRINTED IN CHINA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VEN52 and is the answer not in the manual?

Questions and answers

Related Manuals for Craftmade VEN52

Summary of Contents for Craftmade VEN52

  • Page 1: Table Of Contents

    READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Ventura Installation Guide For Model: VEN52 Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly.

  • Page 2: Safety Tips

    SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS.

  • Page 3: Unpacking Your Fan

    1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included.

  • Page 4: Installation Preparation

    3. Installation Preparation. blade edge To prevent personal injury and damage, ensure that the hanging location allows the blades a inches 7 feet (2.13 m) (76 cm) clearance of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square 12ft.

  • Page 5: Fan Assembly. Pgs

    stop pin 5. Fan Assembly. set screw Remove hanging ball from downrod provided by hanging ball loosening set screw on hanging ball. Lower hanging ball and remove stop pin and then slide hanging ball off of the downrod. [Refer to diagram 1 diagram 1.] Loosen yoke set screws and nuts at top of motor...
  • Page 6 5. Fan Assembly. (cont.) With the hanging bracket secured to the outlet box and able to support the fan, you are now safety cable loop ready to hang your fan. Grab the fan firmly with wood ceiling two hands. Slide downrod through opening in joist hanging bracket and let hanging ball rest on the hanging bracket.

  • Page 7: Wiring

    6. Wiring. CAUTION: Be sure outlet box is properly grounded white supply wire or that a ground wire (GREEN or Bare) is present. ground (green or bare) black supply wire Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code.

  • Page 8: Canopy Assembly

    7. Canopy Assembly. Locate 2 screws on underside of hanging bracket and remove screw closest to the open end of the hanging bracket. Partially loosen the other screw. Lift canopy to hanging bracket. Place rounded part of slotted hole in canopy hanging bracket over loosened screw in hanging bracket and push up.

  • Page 9: Light Kit Assembly

    9. Light Kit Assembly. Remove 1 screw from motor plate on underside of motor and partially loosen the other 2 screws. Align slotted holes in shade with loosened screws in motor plate, allowing motor housing molex plugs from motor housing to come motor plate through hole in middle of shade.

  • Page 10: Handheld Remote Control Assembly

    10. Handheld Remote Control Assembly. remote IN ORDER TO USE THE HANDHELD REMOTE control CONTROL, CONTINUE WITH SECTION 10 for remote cover control assembly instructions. If you have already installed the wall control but do not wish to use the handheld remote control, please proceed to Section 11.

  • Page 11: Automated Learning Process./Activating Code

    11. Automated Learning Process./Activating Code. CAUTION: The wall and/or handheld remote control can be programmed to multiple receivers or fans. If wall control this is not desired, turn wall switch off to any other programmable receiver or fan. Restore electrical power and then, if using wall control, set slider switch on wall control to the ON position.

  • Page 12: Remote/Wall Control Operation

    12. Remote/Wall Control Operation. handheld wall control remote control IMPORTANT: Handheld remote control and wall III IV control must be SYNCHRONIZED with fan in order to properly function. Fan SPEED control buttons1: Use to control the ceiling fan speed 1-6 Fan OFF button 2: Use to turn the fan off REVERSE function button 3:...

  • Page 13: Troubleshooting

    Service at 1-800-486-4892 to arrange for return of fan. 2. Verify that wall control is wired properly. Return fan, shipping prepaid, to Craftmade. We will repair 3. Check to be sure fan is wired properly. or ship you a replacement fan, and we will pay the return 4.

Table of Contents