Craftmade Viva Installation Manual

Hide thumbs

Table of Contents

Quick Links

Download this manual

Viva

Installation Guide

For Model:

VIA72

WARNING:

DC Motor will not

operate until blades

are installed

Remote control

and receiver are

pre-programmed.

E192641

net weight of fan: 20.28lb (9.2 kg)

READ THESE INSTRUCTIONS AND

SAVE THEM FOR FUTURE USE

Need help?

Do you have a question about the Viva and is the answer not in the manual?

Questions and answers

Summary of Contents for Craftmade Viva

Page 1: Table Of Contents
READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Viva Table of Contents: Installation Guide Safety Tips. pg. 3 Unpacking Your Fan. pg. 4 For Model: Parts Inventory. pg. 4 VIA72 Installation Preparation. pg. 5 Hanging Bracket Installation. pg. 5 Fan Assembly.
Page 2 Activating Your New Smart Fan; Downloading the Bond Home App • Using your smart device, navigate to the application store (Apple App store or Google Play), download the free Bond Home app and create account. • Ensure the fan and receiver are receiving power from the house supply using the remote control to turn the fan and light ON and OFF.
Page 3: Safety Tips
Light kit is dimmable to 10% with the remote control included. Distributed by: Craftmade, 3901 S. 20 Avenue, DFW Airport, TX, 75261; 800-486-4892 NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may occur.
Page 4: Unpacking Your Fan
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included.
Page 5: Installation Preparation
3. Installation Preparation. blade edge To prevent personal injury and damage, ensure that inches 7 feet the hanging location allows the blades a clearance (2.13m) (76cm) of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square 12ft.
Page 6: Fan Assembly. Pgs
5. Fan Assembly. Remove hanging ball from downrod provided by stop pin loosening set screw on hanging ball. Lower hanging set screw ball and remove stop pin and then slide hanging ball off of the downrod. [Refer to diagram 1.] hanging ball Loosen yoke set screws and nuts at top of motor housing.
Page 7 5. Fan Assembly. (cont.) Thread safety cable and wires through hanging ball and then slide hanging ball over set screw hole downrod--the top of the downrod should be noted as having a set screw hole; use this hole stop pin when setting the set screw.
Page 8: Wiring
6. Wiring. white supply wire WARNING: Turn off circuit breakers to current ground (green fixture from breaker panel and be sure switch is black supply wire or bare) turned to the OFF position. ground (green/bare) CAUTION: Be sure outlet box is properly ground (green) grounded and that a ground wire (GREEN or...
Page 9: Blade Assembly
8. Blade Assembly. WARNING: To reduce the risk of serious bodily injury, DO NOT use power tools to blade attachment assemble the blades. If screws are screws and washers overtightened, blades may crack and break. Locate 15 blade attachment screws and rubber washers in one of the hardware packs.
Page 10: Light Kit Assembly (Optional)
9. Light Kit Assembly. (optional) motor housing Remove 1 screw from motor plate on underside of motor and partially loosen the other 2 screws. Align slotted holes in center of fitter plate with loosened screws in motor plate, allowing female motor plate plug from motor housing to come through hole in...
Page 11: Automated Learning Process./Activating Code
10. Automated Learning Process./Activating Code. CAUTION: The remote control transmitter can be programmed to multiple receivers or fans. If this is not desired, turn wall switch off to any other programmable receiver or fan. Remove battery cover on backside of remote control by loosening screw on battery cover.
Page 12: Remote Control Operation
11. Remote Control Operation. button - Turns fan ON/OFF button - Use to control fan direction button - Use to decrease fan speed. Blue LED lights will show the current speed. button - Use to increase fan speed. Blue LED lights will show the current speed.
Page 13: Testing Your Fan
12. Activating Your Ceiling Fan Smart Features. (cont.) 7. Test the fan functions: - You have the option to disable the light function if your fan does not have a light. 8. Select “YES, IT WORKS. ” 9. Specify information about your fan: -Select “Location”...
Page 14: Troubleshooting
2. Check to be sure fan is wired properly. customerservice@craftmade.com. 3. Learning process between fan and remote control In the event a product is no longer available, CRAFTMADE transmitter may not have been successful and code will make best efforts to offer a comparable product or was not activated.

This manual is also suitable for:

Via72 Via72fbsb3 Via72pln3