Table of Contents
Advertisement
.
Electrical
requirements
Electrical Shock Hazard
l
Improper connectlon of the
equipment-grounding
conductor can result in a risk
of electrical shock. Check
with a qualified electrician or
service techniclan If you are
In doubt as to whether the
appliance is properly
grounded.
l
Do Not use an extension
cord
with this appliance. Such use
may result in a fire, electrical
shock, or other personal
injury.
A
120.voft, 60.Hz, AC only, 15.or-20
ampere, fused, electrical supply is
required. A time-delay fuse or circuit
breaker is recommended.
It is
recommended
that a separate circuit
serving only this appliance be
provided.
Recommended
grounding
met hod
DO NOT, UNDER ANY
CIRCUMSTANCES, REMOVE THE
POWER SUPPLY CORD GROUNDING
PRONG.
For your personal safety, this
appliance must be grounded. This
appliance is equipped with a power
supply cord having a 3-prong
grounding
plug. To minimize
possible shock hazard, the cord
must be plugged into a mating
3-prong, grounding-type
wall
receptacle, grounded in accordance
with the National Electrical Code,
ANSVNFPA 70.latest edition, and
local codes and ordinances.
See
Figure 1. If a mating wall receptacle
is not available,
it
is the personal
responsibility
and obligation of the
customer to have a properly
grounded, 3-prong wall receptacle
installed by a qualified electrician.
Figure 1
wall receptacle
3-p&g
grounding
Water supply
requirements
Use only l/4" copper tubing for
water line.
The water line to therefrigerator
must provide 15-100 psi water
pressure.
The preferred method of installing
the plumbing to the refrigerator is
through the wall. An optional
method is installing the water line
through a floor opening.
If the
copper tubing is installed through
the floor, the hole cut in the floor
must be angled 49 toward the front.
You will need enough l/4"- copper
tubing to connect from water line to
relrigerator,
a saddle-type
valve and
a union. Rough in the water line
before installing the refrigerator.
See
steps that follow.
Product/Property
Damage
Do Not install copper tubing
in an area where temperatures
drop below freezing.
To do so may result in water
damage.
1
-Find a 3/8" to 1" vertical cold
water line near the refrigerator.
Measure the distance from the
cold water line to the refrigerator
location.
Add 24 inches for the
final length of
copper tubing
you will need.
Cut both ends
of copper
tubing.square.
Z-Turn off
main water
supply and
clear water
line
I
Electric Shock Hazard.
Electric drill must be grounded
to prevent severe or lethal
shock if water is in line and
enters drill during
use.
Failure to ground drill may
result in personal
injury.
3.
Ground electric drill or use a hand
drill. _Drill a 3/l 6" hole in vertical
cold water line. Attach a saddle
valve to the water line with a
clamp in an easily accessible
location.
Insert a washer
between clamp and line. Check
that inlet end is solidly in the drill
hole. Tighten packing nut.
Tighten the pipe clamp screws
evenly so washer makes a
watertight
connection.
Do Not
overtighten
or copper tubing
could be crushed.
4. Slide.compression
nut and sleeve
on copper tubing.
Insert end of
copper tubing completely into the
outlet valve.
Tighten compres-
sion nut to outlet with an adjust-
able wrench.
Do Not overtighten.
Product Damage
Flush at least 2 qts. of water
through the copper tublng and
Into a bucket before attaching to
the refrlgerator to get rid of any
particles In water Ilne. Check for
water leaks around the saddle
valve.
Failure to do so may result In
product damage.
5. Run water through water line,
valve and copper tubing into a
bucket to flush out any particles in
the water line. Turn the saddle
valve to the "OFF" position.
6.
Route copper tubing to the
refrigerator
location.
compression
nut
copper
tubing
sleeve
union
7. Slide compression
nut and sleeve
over water line.
8.
Connect union to compression
nut and sleeve and tighten.
Do
Not over-tighten.
L1pow~o~~pply
\
-
retainer
Page 7
Advertisement
Table of Contents
