Remote Engine Starting - Omega Crime Guard 810i6 Operation Manual

Feature #3 Automatic Rearming
Factory Default Setting Off
press "arm/lock" button to program
(
Options:
On without doors locking ( press "disarm/unlock" button to program
press "II" button to program
On with doors locking (
"Automatic Rearming", described on page 11, prevents the system from becoming
accidentally disarmed by having it arm itself after being disarmed, if a door is not
then opened or the ignition turned on. Options are to have Automatic Rearming
operate with or without also locking the doors when the system does rearm.
Feature #4 Starter Interrupt Functions
Factory Default Setting Alarm Only
press "arm/lock" button to program
(
Options:
Off ( press "disarm/unlock" button to program
press "II" button to program
Automatic (
press "III" button to program
Alarm & Anti-Grind (
This feature controls the Starter Interrupt circuit, in several ways. In its default
setting, "Alarm Only", the Starter Interrupt is operable whenever the alarm is armed.
The Starter Interrupt can also be used to prevent the accidental grinding of the
starter, by trying to start the vehicle when it is already running by remote starting
(as when the ignition key is turned to "run" to drive the vehicle).
The "Automatic" option will cause the Starter Interrupt output to automati-
cally engage 90 seconds after the ignition switch is turned "off", and also 90 sec-
onds after disarming the system. This automatic engagement will occur even if the
security system is in a disarmed state, but not if it is in Valet Mode. Once the
Starter Interrupt output is activated, the system must be armed, then disarmed with
the transmitter, or placed into the Valet Mode by pressing and holding the Valet
Switch for 2 seconds to disengage it. There are no Status Light indications with this
automatic form of Starter Interrupt.
Programming this feature off completely eliminates the Starter Interrupt out-
put, while leaving all other system operations fully functional.
Feature #5 Ignition Activated Override
Factory Default Setting Off
Option: On
This feature allows an activated system to be overridden and disarmed by simply
turning th gnition switch on within 10 seconds of the system's activation. After
e i
10 seconds, the Emergency Override must be performed or the transmitter "dis-
arm/unlock" button can be used to disarm the system.
)
)
)
)
)
( press "disarm/unlock" button to program
press "arm/lock" button to program
(
Page - 28
The remote engine starting feature should not be used when
the vehicle is parked in an enclosed structure or garage!
)
Your system offers the ultimate in comfort and convenience- remote engine
starting. This feature allows the vehicle's interior to be warmed in the winter or cooled
in the summer before you enter the vehicle. Simply leave the climate controls set
to the desired settings when leaving the vehicle prior to using the remote starting
feature.
The following pages explain the remote engine starting operations. If the
vehicle has a manual transmission, a special procedure is required when exiting the
vehicle to enable the ability to remote start. Otherwise, the actual activation of
remote start is the same for automatic or manual transmission vehicles.
• When leaving the vehicle before remote starting, remember to set the climate
)
controls to the desired heating or air conditioning settings.
• If desired, the system's alarm function may be armed or disarmed as needed
during remote start operations (the system must be disarmed before entering
the vehicle).
Pressing and releasing the "
Remote start if configured to do so.
The system's reaction: The system will respond first by rapidly flashing the
Status Light in green color, then by turning on the ignition and flashing the parking
lights once. Then the starter will engage until the engine runs; 10 seconds later the
parking lights will illuminate steady during the period that the engine is running
from being remotely started. (having them flash instead is an option).
The engine will run for 10 minutes (the factory-set period). Other time periods may
be programmed, if desired, by referring to the "Programming Features" section. At
any time during during remote start mode you can press the remote start button again
to restart the engine run timer. To remotely stop it press and release the transmitter's
remote start command again. The system will stop the engine, and extinguish the
parking lights.
)
)
Should the engine fail to start on the first attempt, the system will subsequently
make as many as three further attempts, as needed. Please note that each starting
attempt takes approximately 20 seconds for the system to check the vehicle's status,
cycle the ignition and starter circuits, and then monitor vehicle status again before
the next attempt.

Remote Engine Starting

How to Activate Remote Starting
III " button 2 times in 5 seconds will activate the
Page - 13