Page 3
MU-200C 1.55 m 1.05m Locate the MU-150C out of direct sun- light for optimum viewing. When lifting the display unit, hold it together with the cover. Grasping by the cover alone may allow the display unit to fall, resulting in...
A Word to the Owner of the MU-150C FURUNO Electric Company thanks you for purchasing the MU-150C 15” Multi-Purpose LCD Display. We are confident you will discover why the FURUNO name has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world.
EQUIPMENT LISTS Standard supply Name Display Unit MU-150C SP10-02801 Spare Parts * SP10-02802 CP10-04910 Installation Materials * CP10-04920 FP10-02501 Accessories * FP10-05401 Bracket * FP10-02510 Option Name Bracket * FP10-02510 Hood (Landscape) FP10-02502 Hood (Portrait) FP10-02503 * = See packing list at end of manual.
1 MOUNTING Refer to the outline drawing at the end of the manual for mounting dimensions. Note: The LCD is made of glass. Handle it with care. 1.1 Display Unit The display unit may be flush mounted in a panel or on a desktop, using the optional bracket.
Page 9
Mounting dimensions for landscape orientation 4. Reattach the cover. 5. For the portrait model only, attach the FURUNO logo seal (supplied in the accessories) at the top left corner. Remove the logo seal from the bottom left corner. Display Unit...
Desktop mounting The display unit can be mounted on a desktop, using the optional bracket (Type: FP10-02510, Code No.: 001-414-510). 1. Fasten the mounting base (lower) to the mounting location with four sets of hex head bolts, spring washers, flat washers and nuts. FRONT 2.
Page 11
(local supply) at the rear of the MU-150C. For use of the cable type 06S4078 (from a control section), cut off the connector’s rubber cover and remove the fixing metal to enable connection.
Page 12
5. Grease the two hex head bolts for fastening the display unit to the mounting base (lower). 6. Fasten the display unit to the mounting base (lower) with the two hex head bolts greased at step 5. Fastening the mounting base (lower) to the display unit 7.
Page 13
1.1.1 Hood (option) A hood (portrait or landscape) is optionally available. Attach it to the display unit with Velcro tape as shown below. 1. Attach nine sets of Velcro tape to the display unit at the locations shown below, in as straight as possible.
2 WIRING 2.1 Wiring External Equipment Connect external equipment to the MU-150C by referring to the drawings in this section. A cable with connector at both ends is provided to connect equipment. General-purpose monitor To use the MU-150C as a general-purpose monitor, connect equipment with a mini D-SUB 15P connector.
Page 15
Connecting FCV-1200 series and CH-250 Using the cables designated below (or equivalent) to connect the FCV-1200 series or CH-250 makes their interface unit of the FCV-1200 series and CH-250 unnecessary. The mini D-SUB 15 P connector cannot be used to connect the FCV-1200 series and CH-250. Display unit, rear view, wiring using specialty cables Notes on wiring For AC specification, solder connector SRCN6A13-3S (supplied in installation materials)
Page 16
Cable 06S4078 is of waterproof construction, however, the MU-150C is not waterproof (specification IPX0). Therefore, remove rubber cover and fixing metal from the display side of the cable. Remove fixing metal. Remove rubber cover. D-sub connector...
3 ADJUSTMENTS Controls for adjustment of the picture are provided on the rear of the display unit. Open the small cover to access the controls. 100-240 VAC POWER 50-60 Hz S2 S3 DATA/VIDEO IN NMEA CONT Rear panel (AC type) EXTBRILL BRILL BRTP...
3.1 Picture Adjustment Contrast and picture are adjusted with [S1]: Opens menu; selects menu items. [S2]: Increases setting. [S3]: Decreases setting. [S4]: Initializes setting. Note: Though “EXIT” is printed on the CONE Board (10P6877), the function of S4 switch is “RESET.”...
J17 as below. J17: Brilliance control circuit selection 1-2: Brilliance is adjusted from the MU-150C (default setting) 2-3: Brilliance is adjusted from the control unit of the FCV-1200 series or CH-250 Note: Do not change the setting of the J16 or J18. The default setting for both is “1-2”.
POWER switch: is turned on and goes off when the unit is turned off. To turn the MU-150C on and off from the control unit of a video sounder such as the FCV-1200 series, turn on the POWER switch of the MU-150C. Note that with the MU-150C turned on and the FCV-1200 turned off the LED on the MU-150C lights in red.
5 MAINTENANCE, TROUBLESHOOTING 5.1 Maintenance Routine maintenance Regular maintenance is important for good performance. Check the following on a regular basis to keep the equipment in good operating condition. Check that the connectors at the rear of the display unit are tightly fastened. Check the ground wire and ground terminal for rust.
– there are no user serviceable parts inside. Refer any work to a qualified technician. Reason for no picture Battery voltage too high. Fuse has blown. Cable between MU-150C and external equipment has loosened. Power cable has loosened. Troubleshooting table Check battery voltage.
Modification for Switching from Landscape to Portrait Orientation To use the MU-150C for portrait with the CH-37, FCV-1200 series, FCV-1500 series or FR-1760DS, the LCD assembly must be turned 180°. 1. Place the display unit on a workbench with the LCD side down. It is recommended to place the unit on cushioning material so as not to place pressure on knob.
Page 24
4. Referring to the arrows in the figure below for location, disconnect the connector and four power switch tag terminals and release cable from CK clamp. Note: When disconnecting the tag terminals, pull them by the metal part of the terminal. Do not disconnect by pulling the cable –...
Page 25
5. Unfasten the eight screws marked with the arrows in the figure below. 6. Release the cable from the clamp marked with the gray arrow in the figure above. 7. Turn the LCD assembly 180°. 8. Fasten screws unfastened at step 5. (Torque: 0.39 ±0.04 Nm; 4 ±0.4 kgm) 9.
Page 26
17. Fasten the cover near the power section and connectors with remaining four screws. (Torque: 0.78 ±0.08 Nm; 8 ±0.8 kgm) 18. Attach the FURUNO logo (supplied) at the cavity in the upper left corner of the display unit. AP-4...
PACKING LIST PACKING LIST PACKING LIST PACKING LIST MU-150C-H-DC-CS MU-150C-H-DC-CS MU-150C-H-DC-CS MU-150C-H-DC-CS N A M E ユニット ユニット ユニット ユニット UNIT UNIT UNIT UNIT 15型カラーLCD表示器 MULTI-PURPOSE LCD DISPLAY 予備品 予備品 SPARE PARTS SPARE PARTS 予備品 予備品 SPARE PARTS SPARE PARTS ヒューズ FUSE 付属品 付属品...
Page 30
PACKING LIST PACKING LIST PACKING LIST PACKING LIST MU-150C-H-AC-CS MU-150C-H-AC-CS MU-150C-H-AC-CS MU-150C-H-AC-CS N A M E ユニット ユニット ユニット ユニット UNIT UNIT UNIT UNIT 15型カラーLCD表示器 MULTI-PURPOSE LCD DISPLAY 予備品 予備品 SPARE PARTS SPARE PARTS 予備品 予備品 SPARE PARTS SPARE PARTS ヒューズ FUSE 付属品 付属品...
Page 40
Printed in Japan All rights reserved. All rights reserved. Pub. No. OME-20250 Pub. No. OME-20250 ( ( YOTA YOTA ) ) MU-150C MU-150C Your Local Agent/Dealer Your Local Agent/Dealer FIRST EDITION : FIRST EDITION : JAN JAN. . 2002 2002 : : OCT OCT.