Page 2
・ 機器の修理・使用方法等に関するお問い合わせは、お買い上げの販売店・代理店、最寄りの 当社支店・営業所あてへお願いします。 ・ FURUNO Authorized Distributor/Dealer お問い合わせは 本書の無断複写複製(コピー)は特定の : JAN. 2023 場合を除き、当社権利侵害になります。 : MAR. 17, 2023 Printed in Japan Pub. No. OMC-45200-A1 ( TEHI ) MU-152HD 00019975310...
Page 3
How to discard a used battery Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter on Maintenance. If a battery is used, tape the + and - terminals of the battery before disposal to pre- vent fire, heat generation caused by short circuit.
Page 4
Use of a wrong fuse can result in damage to the equipment. Continued use of the equipment can cause fire or electrical shock. Contact a FURUNO agent for service. Do not place any object near the exhaust or intake vent.
Page 5
Steering Standard compass compass Do not install the equipment where it MU-152HD 0.60 m 0.35 m may get wet from rain or water splash. Water in the equipment can result in fire, When lifting the display unit, hold it electrical shock or damage to the together with the hard cover.
FOREWORD A Word to the Owner of the MU-152HD FURUNO Electric Company thanks you for purchasing the MU-152HD 15” Marine Display. We are confident you will discover why the FURUNO name has become synonymous with quality and re- liability. Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for quality and reli- ability throughout the world.
FAR-15x8, GD-300, FCV-1900, etc. HDMI FCV-38, CH-500/600, etc. VIDEO (NTSC/PAL) CCD camera, DVD recorder, etc. FAR-1417/1427 Processor Unit Environmental category MARINE DISPLAY MU-152HD: Protected from the weather MU-152HD 12-24 VDC Connectable equipment Equipment Resolution Signal CSH-5L/8LMK2 CH-500/600 HDMI FCV-38 XGA/SXGA...
EQUIPMENT LISTS Standard supply Name Type Code No. Remarks Marine Display MU-152HD-A – w/ Hard cover Spare Parts SP26-01001 001-621-760 1 set Cable Assy. MJ-A3SPF0017A- 000-175-421-10 050ZC Flush Mount Fixture CP26-02601 001-621-770 1 set Installation Materials CP26-02602 001-621-780 1 set...
MOUNTING, WIRING Preparation Mounting type The display unit can be installed in the following methods. See the outline drawing at the back of this manual for mounting dimensions. • Flush mounting, fixed at rear (standard) • Flush mounting, fixed at front (option) •...
Page 11
1. MOUNTING, WIRING The upper edge of the hard cover Pull the upper edge forward by pressing here with thumbs. How to remove the hard cover To attach the hard cover, follow the illustration in the figure below. Cutout Cutout Push the tabs of the bottom of the hard cover Set the tabs on the top...
1. MOUNTING, WIRING Flush Mounting, Fixed at Rear This is the standard installation method. Flush Mount Fixture 15 CP26-02601 (code no. 001-621-770) Name Type Code No. Remarks IM List JE07002-Y533 000-199-746-10 Mount metal 15 JE07002-Y528 000-199-988-10 Butterfly bolt JE82001-0013 000-199-986-10 Butterfly nut JE82001-0014 000-199-987-10...
Page 13
1. MOUNTING, WIRING 2. Attach the flush mounting sponges H15 and V15 in the order shown in the figure below. Fmount sponge H15 for top and bottom Fmount sponge V15 for right and left 3. Connect all cables at the back of the display unit. See section 1.7. 4.
Page 14
1. MOUNTING, WIRING 5. Attach the attachment 15 to the left and right sides of the back of the display unit with the sup- plied washer head screws. Washer hear screws (Three on each side) Attachment 15 (One on each side) 6.
Page 15
1. MOUNTING, WIRING 7. Fasten the mount metal 15 to the right and left sides of the rear of the display unit with the washer head screws (6 places). Mount Metal 15 Washer Head Screw 8. Loosely fasten the butterfly bolts, in the order of the number shown in the figure below so that the protectors touch the mounting panel.
1. MOUNTING, WIRING Flush Mounting, Fixed at Front If there is not enough space to fix the display unit from the rear, you can fix it from the front with the optional Front Fixed Flush Mount Kit JE07002-B022 (code no. 001-634-650). The LCD Retrofit Kit JE07002-B020 (code no.
Page 17
1. MOUNTING, WIRING 2. Attach the flush mounting sponges H15 and V15 in the order shown in the figure below. Fmount sponge H15 for top and bottom Fmount sponge V15 for right and left 3. Attach the flush mounting panel (15) to the display unit from the rear with the washer head screws (M410, 8 places, torque: 1.2 N•m).
Page 18
1. MOUNTING, WIRING 6. Fix the display unit to the cutout with the self tapping screws (4 places). Self tapping screw Fixing with LCD Retrofit Kit JE07002-B020 1. Attach the flush mounting sponges H15 and V15 in the order shown in the figure below. Fmount sponge H15 for top and bottom Fmount sponge V15...
1. MOUNTING, WIRING 2. Attach the flush mounting panel (15) to the display unit from the rear with the spacers and washer head screws (M410, 8 places, torque: 1.2 N•m). Do not confuse the top and bottom of the panel and check that screw holes on the panel and unit match. Washer Head Screw and spacer Narrow...
Page 20
1. MOUNTING, WIRING Name Type Code No. F-Mount Hood Gasket Side 15 JE07002-Y571 000-199-703-10 Hood Fixing Plate 15 JE07002-Y572 000-199-704-10 Knob M4 JE07002-Y562 000-199-692-10 Flat Head Screw J6-SSA3-06200 000-199-693-10 Flush Mounting Template C42-00908 000-172-635-10 1. Make a cutout in the mounting location with the flush mounting template (included). 368±1 (14.49”) 4-ø18(0.71”)* The drill bit with a diameter of 18 mm or...
Page 21
1. MOUNTING, WIRING 3. Fix the hood fixing plates to the right and left of the display unit with the flat head screws (M38, 6 places, torque: 0.6 N•m). Hood Fixing Plate 15 Flat Head Screw Attachment 15 Hood Fixing Plate 15 4.
1. MOUNTING, WIRING 7. Slide the cutouts of the hood assembly to the knobs. Knob (4 pcs.) Hood (15) Assembly Hood Fixing Plate 15 Cutout (4 places) 8. Press the top of the hood to fit the knobs in the cutouts. Press Press 9.
Page 23
1. MOUNTING, WIRING 1. Loosen the knobs of the hanger 15 assembly to separate the hanger bracket 15 assembly from the hanger. Hanger 15 Assembly Hanger Bracket 15 Assembly Knob 2. Set the hanger 15 assembly to the mounting location with four self tapping screws. Self-Tapping Screw 5x20 Hanger 15 Assembly...
1. MOUNTING, WIRING 4. Connect all cables at the back of the display unit. See section 1.7. 5. Loosen the knobs of the bracket support and set them in the notches on the hanger 15 as- sembly. Hanger 15 Assembly Knob 6.
1. MOUNTING, WIRING 3. Attach the flush mount fixtures with the washer head screws to join the two display units. Flush Mount Fixture (4 pcs.) Join the display units with the flush mount fixtures. 4. Fasten the two display units tightly. See step 7 to step 9 in section 1.2. Wiring Refer to figure below and the interconnection diagram at the back of this manual to connect ca- bles.
Page 26
1. MOUNTING, WIRING : Slide switch Referring to below table to set the slide switch according to your vessel’s configuration. Slide Switch Inputs Connected devices Upward: Default setting Upward: Default setting ON (Factory de- Digital input • Radar (Slide switch ON) (Slide switch ON) fault) (DVI, HDMI)
ADJUSTMENTS Adjust the MU-152HD according to the equipment connected. RGB/DVI/HDMI Setting You can adjust the screen from the [RGB], [DVI] and [HDMI] ports separately. Turn on external equipment and adjust the display unit as follows. 1. Select the signal to adjust at the DISP selection window. See section 3.4.
Page 28
2. ADJUSTMENTS 5. Press the or key to adjust the setting. 6. Press the MENU key to close the menu. RGB/DVI /HDMI menu descriptions Menu item Function Setting H_SIZE Adjusts the image size horizontally. Horizontal size: (narrow), (wide) Depending on in- put signal V_SIZE...
2. ADJUSTMENTS Video Composite Signal Setting You can adjust the VIDEO signal from the VIDEO port. The VIDEO signal is also displayed in the PIP window. 1. Select the signal to adjust at the DISP selection window. 2. Press the MENU key to show the menu. 3.
2. ADJUSTMENTS The Menu Window Setting 2.3.1 How to adjust the menu window You can adjust the position and transparency of the menu window on the [OSD] (On Screen Dis- play) menu. 1. Press the MENU key to show the menu. 2.
2. ADJUSTMENTS 2.3.2 How to change the signal name You can change the signal name (“RGB”, “DVI”, “HDMI” or “VIDEO”) to a name (ex. the equipment name) which is easy to understand. The changed name is shown in the DISP selection window, PIP selection window and the indication shown at the upper right of the screen.
OPERATION Controls *: Available when the slide switch at the bottom of rear side is OFF. - Power On/Off.* - Display the brilliance Select the signal to display. Open/Close the menu. adjustment window. Lamp (Lights when - Select the menu and Display the PIP power on.) menu items.
The external equipment connected to the DVI/HDMI port can power on/off the display unit. Note 1: You can not turn on the power with the /BRILL key on MU-152HD. Note 2: If equipment is connected to both DVI and HDMI ports, turn off the power of the connected equipments to turn off the display unit.
3. OPERATION 2. Press the or key to adjust the brilliance (available range: 1 to 50, default: 50). You can also adjust the brilliance by pressing the /BRILL key repeatedly. Note 1: If the display unit is turned off with the brilliance set to minimum, the screen may not be visible depending on lighting conditions.
3. OPERATION 1. With the RGB, DVI or HDMI display shown, press the PIP key to show the PIP window. To hide the PIP window, press the PIP key again. 2. You can move the PIP window by pressing the arrow keys when the menu is closed. Note: You can adjust the size of the PIP window on the [VIDEO] menus.
HDMI : NO SIGNAL VIDEO : NTSC MODEL TYPE: MU-152HD PROGRAM NO. : X.XX ELAPSED TIME : 100000 hour Note: To cancel, press the key. The display is changed to "NO" from "YES". 5. Press the key to select "reset".
MAINTENANCE, TROUBLESHOOTING NOTICE Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment. Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors. Maintenance Routine maintenance Regular maintenance is important for good performance. Check the following on a regular basis to keep the equipment in good condition.
4. MAINTENANCE, TROUBLESHOOTING LCD replacement The life of the LCD is approximately 40,000 hours. The actual number of hours depends on am- bient temperature and humidity. When the brilliance cannot be raised sufficiently, replace the LCD. Fan replacement The life of the fan is approximately 90,000 hours. The actual number of hours depends on ambient temperature.
Application Program AUTO Automatic Black BRILL Brilliance Charge-Coupled Device Type of FURUNO searchlight sonar Type of FURUNO current indicator Type of FURUNO color scanning sonar CTRL Control DISP Display Digital Versatile Disc Digital Visual Interface External Type of FURUNO radar...
Page 88
When a claim is made, FURUNO has a right to choose whether with other electronic devices. The imported product may also be to repair the product or replace it.
Page 89
24 months from installation date provided the work is done by Furuno U.S.A., Inc. or an AUTHORIZED Furuno dealer during normal shop hours and within a radius of 50 miles of the shop location.