Advertisement
CAUTION:
BesureyourgrillisOFFandcool b efore cleaning.
Take carenottochiporscratch thepainted surfaces.
Aswithallappliances, proper c areandmaintenance
willkeep yourgrillintopoperating c ondition and
prolong itslife.Byfollowing t hese cleaning procedures
ona timelybasis, y ourgrillwillstaycleanandwork
properly withminimum effort.
Cleaning TheCookingGrids
Before. ini,tial us.e.and perio.,dically
wesuggest yo.u wash
yourL, O OKIng L_rlas m a mllasoapariawarm water
solution. Youcanusea wash ctotnorvegetable b rush
toclean yourCooking G rids.
Cleaning The Flame Tamers
Periodically you should wash th, e Flame Tamers in a,
soap ane warm water solution, use a vegetable Drusn
to, remove stub.b, o rn burn t-o,n cooking restd,ue..,Drythe.
tlamelamersmorougn_y
Beforeyou reinsfall mem info
the cooking bowl.
Cleaning
The Grease Tray and Receptacle
To reduce the chance ,off[re, t, h e,Grease, p[aining Tray
ang urease Keceptacle snoulg Be ViSUally mspecteg
before each grill use. Remove any grease aria wash
Grease T.ray a,nd.Receptacle with a mild soap and
warm water
SOlUtiOn.
Cleaning the Inside of the Grill Lid
Gre,ase can have a ten,dency to bui!d u,pon the inside
of me L_riH Lia ana cou_a grip onto geCKOr pado wnen
the !idols opened..V,isually_.inspect the insiae of the Gri!l
Lla Before eacn grill use. Kemove any grease ana wasn
with a mild soap and warm water solut=on.
Annual Cleaning
of The Grill Interior
Burning-off the grill after every cookout willkeep it
ready for instant use. However, once a year you should
give the entire grill a thorough cleaning to keep it in top
operating condition. Follow these steps:
1. Turn all Burner Valves to the futl OFF position.
2. Turn the LP gas tank valve to the futl OFF position.
3. Disconnect the regulator from the gas tank. Inspect
the hose with regulator assembly for cracking, cuts
or any other damage, and replace as neccessary
with Sears replacement parts. See Parts List.
4. Remove and clean the Flame Tamers, Cooking
Grids, Cooking Rack and Grill Burners.
5. Cover each Gas Valve Orificewith aluminum foil.
6. Brush the inside and bottom of the grill with a fiber
pad or nylon brush, and wash with a mild soap and
warm water solution. Rinse thoroughly and let dry.
7. Remove aluminum foil from Orificesand check
each Orifice for obstruction.
8. Check each Spark Electrode, adjusting as needed.
The space between the Spark Electrode Tip and
Spark Receiver should be approximately 3/16".
9. Replace the Burners and adjust the Gas Collector
Box. The edge of the collector box should be
overlapping the Burner Port.
10. Replace Flame Tamers and the Cooking Grids.
11. Reconnect the gas source and observe the Burner
flame for correct operation.
Cleaning Exterior Surfaces:
Before initial use, and periodically thereafter, we
suggest you wash your grill using a mild soap and
warm water solution. You can use a wash cloth or
sponge for this process. Do not use a stiff wire or
brass brush that might remove paint during the clean-
ing process.
Cleaning Exterior Stainless Steel Surfaces:
Weathering and extreme heat can cause exterior
stainless steel surfaces to turn tan in color. Machine
oils used in the manufacturing
process of stainless
steel can also cause this tanning color. After removing
the protective PVC film from the Grill Lid and Control
Panel use a Stainless Steel Cleaner to polish the
stainless steel surfaces of your grill. Never use abra-
sive cleaners or scrubbers because they will scratch
and damage your grill. Follow these steps for the best
results.
1. TurntheLPgastankvalve(clockwise)tothefull
OFF
position. Disconnect the regulator and hose assem-
bly from LP gas tank. Cover exposed gasfitting with
aluminum fo_.
2. Remove dirt or grease using a soft cloth and polish
stainless surfaces. Wipe with a soft cloth.
3. Remove aluminum foit from exposed gasfitting and
allow grill to air drybefore attaching the regulator
and hose to yourLP
gas tank.
Keep outdoor cooking gasappliance area clear and free
from combustible
materials, gasoline and other flam-
mable vaporsand liquids.
CAUTION:
1. Do not obstruct the flowofair
forcombustion
and ventilation.
2. Keep the ventilation openings of the cylinder
enclosure cabinet free and clear of debris.
3. Visually check burner flames occasionally to
observe for proper flame pattern as shown below.
BURNER FLAME
27
Advertisement
