Table of Contents
Advertisement
Quick Links
O.L.E.D. Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
IMPORTANT ! In order to provide you with the highest level of security to your
vehicle, this system is equipped with selectable manual override circuitry. It is
possible that you will need to override you security system if the transmitter
becomes lost, or inoperative due to battery failure. Reading the sections on
"Manually Overriding Your System" is necessary to fully understand the procedure
required to enable your vehicle in such situations. In addition, the chart on the last
page of this manual has a section for the particular features and options installed
in your vehicle as well as the override method selected. Although the default
mode is "Valet Switch" operation, the system can be configured for "Custom
Code" operation for enhanced security. Confirm the override mode selected on
the last page of this manual, and familiarize yourself with the section on it's opera-
tion.
FEATURES :
1 Two Way 4 Button 900 MHz OLED Remote Control w/ Side Switch
1 One Way 4 Button 900 MHz Remote Control
Seven Channel Code Learning Programmable Receiver
External Superheterodyne Transceiver Antenna
Single Or Two User Programmable W/Separate Control Outputs
Can Control Up to 4 Different Vehicles
Single Button Lock/Unlock or Separate Button Lock/Unlock or Both
Remote Keyless Entry With Optional Access Guard (must have power door
locks)
Selectable Manual Override Mode
New Enhanced Panic Feature (Any button other than unlock stops siren, no
change to the units state)
Smart Disarm (If triggered, elect to shut off siren, or disarm entire unit )
Adjustable Shock Sensor Via The Transmitter (Pre-Detect Off, Pre & Full Detect
Off, City Mode)
Safe Start Output Controlled From Channel 3 (Option Channel 3 For Trunk, Or
For R/S)
24 Hour Time Start Mode
Cold Temperature Start Mode
2 or 4 Hour Automatic Start Mode
Parking Meter Count Down Timer On OLED Remote
Additional Count Down Timer Mode
Remote Panic In All Modes (Press & Hold Lock /Unlock Button For 3 Seconds
To Engage)
Model XRO9100
Owner's Manual
Page 1
128-8261
1 of 24
Advertisement
Table of Contents
Related Manuals for Audiovox XRO9100
Summary of Contents for Audiovox XRO9100
- Page 1 Model XRO9100 Owner’s Manual O.L.E.D. Remote Start Security System With Plug-In Shock Sensor & Starter Disable IMPORTANT ! In order to provide you with the highest level of security to your vehicle, this system is equipped with selectable manual override circuitry. It is possible that you will need to override you security system if the transmitter becomes lost, or inoperative due to battery failure.
- Page 2 Improved Custom Code Override, User Selectable and Programmable Protected Push Button Valet/Override Switch 7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming Intrusion Alert With Memory Instant Siren Activation Starter Disable Output Additional Engine Immobilizer Output, (Optional Relay Required) True Last Door Arming (Hardwire Only) Defective Zone By-Pass...
-
Page 3: Arming The System - Active
known as a code grabber, which will receive and store the signal from your keychain transmitter and re-transmit at a later time to disarm your system. Your Spread Spectrum Code Hopping transmitters will change their signal and shift from frequency to frequency every time the button is pressed. This makes it nearly impossible for a thief to capture your code. -
Page 4: Arming The System - Passive (Automatic)
Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired. Closing the hood, trunk, or doors will correct the problem and you do not need to disarm the system to make the correction. -
Page 5: Disarming The System
NOTE: If the optional interior illumination circuit was installed, the interior light will flash as well for the full 30 second alarm cycle. DISARMING THE SYSTEM NOTE: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. -
Page 6: While The System Is Sounding
Before turning the key on, examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered. Doors Unlock - Optional 2 Step Doors Unlock - Optional NOTE: If the optional Headlamp illumination feature has been added and has been selected for operation when disarming, as an added convenience, the system will turn on the headlights when the system is disarmed. -
Page 7: Programming Your Custom Override Code
indicated on the last page of this manual, to bypass the alarm system; 1. Open the vehicle door. The alarm will sound. 2. Turn the ignition key to the on position. 3. Within 5 seconds, press and release the valet pushbutton switch. The alarm system will stop sounding and enter the (bypass) mode. -
Page 8: Eliminating The Normal Arm / Disarm Chirps
7. Within 10 seconds, begin to press and release the pushbutton switch to set the units digit. (As per the example, press and release 2 times to set the units digit to 2). 8. Turn the ignition switch to the off position. Immediately observe the LED flash pattern. -
Page 9: Remote Panic Operation
If the chirps were off before you started, then you will hear one chirp indicating they have been turned on. NOTE: Whenever the chirps are bypassed, the 4-chirp intrusion indicator and 3 chirp defective zone indicator will always operate. Since these are important warnings to you that something has happened, they cannot be eliminated. -
Page 10: Remote Starting The Vehicle
keychain transmitter. 1. Within 2 seconds of arming, press and release the ARM button 1 time, to defeat the pre-detect stage of the shock sensor. (The lights will flash and the siren will chirp once.) 2. Within 2 seconds of step 1, press and release the ARM button 2 times, to defeat the pre and full detect stages of the shock sensor. - Page 11 WARNING! Be certain that the vehicle is outdoors before using this or any re- mote vehicle starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged. TO BEGIN THE AUTOMATIC START UP TIMER 1.
- Page 12 ADDITIONAL REMOTE FUNCTION (AUX 2 ) Controlled By: Moving side switch up 3 times and selecting AUX 2 by pressing the #2 Unlock Button. If this auxiliary output is connected to a device in your vehicle,,,the device will immediately activate. ADDITIONAL REMOTE FUNCTION (AUX 3 ) Controlled By: Moving side switch up 3 times and selecting AUX 3 by pressing the #3 Trunk/Key Button.
-
Page 13: Telematic Upgrade
DAILY START TIMER Press the option + lock buttons simultaneously for 1 second at the time you want the vehicle to start. The vehicle will chirp once indicating that the automatic start timer has been activated for the current time when the button combination was pressed. vehicle will then start automatically at the same time the following day, providing that the exit procedure is followed. -
Page 14: Charging The Battery
TRANSCEIVER BUTTONS AND FUNCTIONS TRANSCEIVER ICONS AND THEIR INDICATIONS CHARGING THE BATTERY If on the OLED screen the LOW BATTERY icon comes up or is flashing, this indicates that the internal 3.7V Lithium Polymer battery requires recharging. To charge the battery, connect the changer to the Transceiver by lifting the rubber charge port located on the left side of the transceiver and plugging in the mini USB connector from the home battery charger. - Page 15 120VAC wall socket and the charging will start. If you have the USB to USB cable, found on some wall charge units, than you can also connected to a PC's USB 5 Volt port to charge your transceiver. Additionally if your unit is packaged with the 12 Volt DC adaptor, you can charge the unit is your vehicle by connecting to the accessory plug in the vehicle and connecting the USB mini USB to than to the Transceiver.
- Page 16 On which sets the "0* C, 32*F" Start Sequence for 1 run cycle. Also select different transmitter which may be used for additional vehicles, with similar Audiovox Remote Control Systems. Moving the side switch up one more time will return to the default page shown, or allow 15 seconds to expire and the display will turn off.
- Page 17 lock or unlock the buttons, select melody, vibrate, or both, and view the transceiver's DEMO Mode as shown. To turn off button beep tones, move the side switch down 1 time, press the Lock (1) button to select button beep, than press Lock (1) or Unlock (2) to select the tones on or off.
- Page 18 In other words, this transmitter will control up to 4 vehicles that have similar Audiovox Alarm Sys- tems installed. TX1 is used for your car, TX2, can be for Lou's car, TX3 may be for Maria's car &...
- Page 19 Auxiliary Selection allows the naming of the outputs of your system. Your security system may have additional functions that were connected at time of installation, like right side slider door, left side slider door, Sun Roof Open or Close,,,etc... You can name the function of the output for easy recall. Move the side switch down 5 times to access the Aux page.
- Page 20 XRO9100 STSTEM FUNCTIONS AT A GLANCE DASH LED INDICATIONS RAPID FLASH PASSIVE ARMING/ACTIVE REARMING SLOW FLASHING ARMED DISARMED ON SOLID VALET 3 FLASH... PAUSE INTRUSION ZONE 3 2 FLASH,,,PAUSE INTRUSION ZONE 2 1 FLASH...PAUSE INTRUSION ZONE 1 SIREN CHIRP INDICATIONS...
-
Page 21: Programming Transmitters
PROGRAMMING TRANSMITTERS: At times it may become necessary to program replacement or additional transmitters for use with your system. To do this: 1) With the system unlocked or disarmed, turn the ignition key to the on position. 2) Press and release the pushbutton switch three times The unit will flash the parking lights and or beep the horn once to indicate that the system is in the transmitter program mode. - Page 22 Here you can press and hold the lock & start buttons simultaneously, for controlling the unlock function of the second vehicle. 5) Press and release the program pushbutton switch once to advance to channel 3, start. Here you can press and hold the start & option buttons simultaneously, for controlling the start function of the second vehicle etc..
-
Page 23: Battery Replacement
BATTERY REPLACEMENT The transmitter incorporates a small LED visible through the case which is used to indicate battery condition. You will notice a decrease in transmitter range as the battery condition deteriorates. Transmitter battery replacement is recom- mended at least every 10 to 12 months, depending upon how frequently the transmitter is used. - Page 24 Credit card purchasers can order additional or replacement transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and follow the instructions from the operator interface. © 2007 Audiovox Electronics Corp. 150 Marcus Blvd, Hauppauge, NY 11788 128- 8261 Page 24...