FujiFilm FinePix S3 Pro Owner's Manual page 67

Warning Displays
Warning Displayed
Explanation
Top display
Viewfinder
panel
i CPU Nikkor lens other than G-type
is not set to its minimum aperture.
i Attached flash is not set at TTL
(blinking) (blinking)
Auto Flash in "P" mode.
Batteries have no remaining charge.
—
(blinking/lit)
Non-CPU lens is attached or lens is
not attached.
(blinking) (blinking)
Autofocus is not possible.
—
(blinking)
Overexposure warning (subject is too
bright).
(lit) (lit)
Underexposure warning (subject is
too dark.).
(lit) (lit)
Electronic Subject brightness is beyond
analog camera's exposure range.
exposure
—
display
(blinking)
Shutter speed is set to "
"S" mode.
(blinking) (blinking)
Shutter Shutter speed faster than sync speed
speed is selected in "S" or "M" mode.
indication
(lit)
(blinking)
Flash has fired at full output and
underexposure may have occurred.
—
(blinking)
Malfunction detected.
(blinking) (blinking)
The batteries are low on charge or
— flat.
(lit)
132
eThe table below lists the warning messages displayed on the
top display panel or in the viewfinder.
Remedy
i Set lens to minimum aperture.
i Set the external flash mode to TTL, or set
the camera's exposure mode to "S", "A" or
"M".
Turn the power off and replace batteries
with new ones.
Attach CPU lens (except IX-Nikkor). With a
non-CPU lens, set the exposure mode to
"M" and set the aperture with lens' aperture
ring.
Focus manually.
i In "P" mode, use ND filter (If the warning
indication remains after performing above
remedies in "S" or "A" mode, use ND filter
as well).
i In "S" mode, select faster shutter speed.
i In "A" mode, select smaller aperture
(larger f-number).
i In "P" mode, use flash (If the warning
indication remains after performing above
remedies in "S" or "A" mode, use flash as
well).
i In "S" mode, select slower shutter speed.
i In "A" mode, select larger aperture
(smaller f-number).
When the subject is too bright, use ND filter
and when the subject is too dark, use flash.
The electronic analog exposure display
remains blinking when the flash is used.
™ ™
" in Cancel the " " or select "M" mode.
Release the shutter as it is to take a flash
picture (Shutter speed automatically shifts
to 1/180 sec.).
Shoot again after confirming focus distance,
aperture or flash shooting distance range.
Set the Exposure mode dial to "M" and
press the shutter button again. If the
warning indication remains, or this warning
appears frequently, contact you FUJIFILM
dealer.
Turn the camera off and replace the
batteries. Then turn the camera back on
and try again.
Warning Displayed
Explanation
Top display
Viewfinder
panel
The batteries are low on charge or
the camera mechanism has stopped
due to cold and cannot take pictures.
—
(blinking)
In certain cases, due to static electricity or poorly loaded batteries, the FinePix S3 Pro microcomputer
may turn the camera off, even with fresh, properly installed batteries. For the same reason, the
operation of camera may not advance properly during either "USB mode" or "IEEE 1394 mode". In
each of these cases, to resume operation, simply turn the power off, then turn it on again. Or, remove
and reinstall the batteries. When this happens, the camera settings may be initialized. Check the
required camera settings before using the camera.
Remedy
Turn the camera off and replace the
batteries. Then turn the camera back on
and try again.
If this does not resolve the problem, set the
Exposure mode dial to "M", set the focusing
mode to "M" (Manual focus), press the
shutter button and then briefly turn the
camera off.
133