Cancelling Custom Settings; Custom Settings List - FujiFilm FinePix S3 Pro Owner's Manual

CUSTOM SETTING ( CSM )
The custom settings allow to modify camera functions such as how information is displayed in the
viewfinder and which functions are assigned to which buttons.
1
2
ＣＵＳＴＯＭ ＳＥＴＴＩＮＧ ＣＵＳＴＯＭ ＳＥＴＴＩＮＧ
１ ＢＲＡＣＫＥＴＩＮＧ ＯＲＤＥＲ １ ＢＲＡＣＫＥＴＩＮＧ ＯＲＤＥＲ
０ ０ ＭＥＴＥＲＥＤ ＶＡＬＵＥ→ＵＮＤＥＲ→ＯＶＥＲ ＭＥＴＥＲＥＤ ＶＡＬＵＥ→ＵＮＤＥＲ→ＯＶＥＲ
１ ＵＮＤＥＲ→ＭＥＴＥＲＥＤ ＶＡＬＵＥ→ＯＶＥＲ ＵＮＤＥＲ→ＭＥＴＥＲＥＤ ＶＡＬＵＥ→ＯＶＥＲ
ＭＡＩＮ ＭＡＩＮ ＭＥＮＵ ＭＥＮＵ ＳＵＢ ＳＵＢ ＳＥＴＴＩＮＧ ＳＥＴＴＩＮＧ
0 1 0 2
0 3
When you have finished the settings, set the exposure mode dial to a setting other than "CSM".
3
●
!
The custom settings are retained when the camera is turned off.

Cancelling custom settings

1 0
0 2 2 0
110
Set the Exposure mode dial to "CSM".
1 Turn the Main-command dial to select an option.
2 Turn the Sub-command dial to change the
setting.
3 " E " appears on the top display panel.
1 Set the Exposure mode dial to "CSM".
2 Hold down the " c " and " b " buttons together
for at least 2 seconds (green markings are
positioned alongside).
The top display panel flashes briefly and the
settings are reset.
h All the custom settings are reset to their default
values.
h The ISO sensitivity is reset to 200.

■ Custom settings list

No. Setting Display
0: METERED VALUE
1 BRACKETING ORDER
➡ UNDER ➡ OVER
(default)
1: UNDER ➡
METERED VALUE
➡ OVER
2 ON-DEMAND GRID 0: OFF (default)
LINES DISPLAY 1: ON
ILLUMINATION FOR 0: AUTO (default)
3
FOCUS AREA 1: OFF
2: ON
4 FOCUS AREA 0: NORMAL (default)
SELECTION 1: ENABLES
ROTATION
5 AE-LOCK 0: DISABLED (default)
1: ACTIVATED
6 LONG EXP. (BULB) AT 0: DISABLED (default)
MANUAL MODE 1: ACTIVATED
7 CLOSEST-SUBJECT- 0: ENABLED (default)
PRIORITY DYNAMIC AF 1: DISABLED
AT AF-S MODE
8 CLOSEST-SUBJECT- 0: DISABLED (default)
PRIORITY DYNAMIC AF 1: ENABLED
AT AF-C MODE
9 AE/AF LOCK BUTTON 0: AE/AF LOCK
(default)
1: AE LOCK ONLY
2: AF LOCK ONLY
3: AE REMAINS
LOCKED
4: AF OPERATION
10 COMMAND DIAL 0: DISABLED (default)
FUNCTIONS 1: ENABLED
11 MULTIPLE EXPOSURE 0: SINGLE SHUTTER
RELEASE (default)
1: CONTINUOUS
SHUTTER
RELEASE
Details
Allows you to change the compensation sequence
when auto exposure bracketing is used.
If you display the On-Demand Grid Lines, you can use
the intersections of the horizontal and vertical lines to
position your main subject in the shot or align one of the
horizontal lines with the horizon. This allows you to
compose the desired shot while monitoring the subject's
size and the balance.
Specifies the illumination used for the focus area in the
viewfinder.
Selecting cyclic focus area selection allows you to
select the opposite focus area without changing which
part of the 4-direction button you have to press.
Set this parameter to "1" to apply the AE lock when the
shutter button is pressed half way.
Select "1" to take bulb shots in the "M" exposure mode.
If you select "1", Closest-subject Priority Dynamic AF is
not used in AF-S mode.
If you select "1", Closest-subject Priority Dynamic AF is
used in AF-C mode.
Normally, AE lock (exposure recording) and AF lock
(focus lock) are both applied concurrently when you
press the "AE-L/AF-L" button. However, this can be
changed so that only AE lock or only AF lock is applied,
or so that that the AE lock status is maintained. If the
AE/AF lock is used with the "Maintain AE lock" setting,
pressing the "AE-L/AF-L" button again or releasing the
shutter cancels the lock.
In addition, though the auto focus (AF) normally
operates when the shutter button is pressed down
halfway, you can change this so that AF operates when
the "AE-L/AF-L" button is pressed. (In this case, AF
does not operate when the shutter button is pressed
down halfway.)
Use this setting to change the Main-command dial and
Sub-command dial operation during photography.
0: Main: Changes the shutter speed.
Sub: Changes the aperture.
1: Main: Changes the aperture.
Sub: Changes the shutter speed.
Changing this setting allows you to use continuous
shooting for multiple exposure shots.
5
111