Specifying Images For Printing On The Camera - FujiFilm FinePix F810 Owner's Manual

6.3 USING FinePixViewer
5 When the message appears, click the [OK] button.
Check your selection carefully since the process
cannot be cancelled once you click [OK] button.
6 Automatic uninstallation begins.
When uninstallation ends, click the [OK] button.
Macintosh
Mac OS 9.2
■ Uninstalling Exif Launcher, FinePixViewer
1 After you have quit Exif Launcher in "Exif Launcher Settings" in the FinePixViewer "Settings"
menu, move the Exif Launcher file from the "Startup Items" folder in the System folder to the
Trash. Then select "Empty Trash" in the "Special" menu.
2 After you have exited FinePixViewer drag the installed FinePixViewer folder to the Trash. Then
click "Empty Trash" in the "Special" menu.
Mac OS X
■ Uninstalling FinePixViewer
Quit FinePixViewer. Then drag the installed FinePixViewer folder to the Trash and select "Empty
Trash" in the "Special" menu.
108
6.4 CONNECTING THE CAMERA DIRECTLY TO THE PRINTER
— PictBridge FUNCTION
When a printer that supports PictBridge is available, images can be printed by connecting the
camera directly to the PictBridge-compatible printer without using a PC.
●
!
When the PictBridge function is used to print images shot using WIDE, the left and right edges of the images may be
cropped. The print size is specified on the printer. Refer to the instruction manual for the printer.
●
!
In PictBridge function, images photographed on other than a camera may not be printed.

6.4.1 Specifying images for printing on the camera

1
0 1 3 0
2 0
ＳＥＴ−ＵＰ ＳＥＴ−ＵＰ
１ ２ ３ ４
ＡＦ ＩＬＬＵＭＩＮＡＴＯＲ ＡＦ ＩＬＬＵＭＩＮＡＴＯＲ ： ＯＮ ＯＮ
ＦＲＡＭＥ ＮＯ． ＦＲＡＭＥ ＮＯ． ：ＣＯＮＴ． ：ＣＯＮＴ．
ＵＳＢ ＭＯＤＥ ＵＳＢ ＭＯＤＥ
ＣＣＤ−ＲＡＷ ＣＣＤ−ＲＡＷ ： ＯＦＦ ＯＦＦ
ＯＫ ＯＫ ＳＥＴ ＳＥＴ ＢＡＣＫ ＢＡＣＫ ＣＡＮＣＥＬ ＣＡＮＣＥＬ
2
3
0 1
2 0
4
ＵＳＢ ＵＳＢ
ＣＨＥＣＫＩＮＧ ＵＳＢ ＣＨＥＣＫＩＮＧ ＵＳＢ
1 Slide the Power switch to the side to turn the
camera on.
2 Select " ®
" in "USB MODE" in the "SET-UP"
menu (➡P.85).
3 Slide the Power switch to the side to turn the
camera off.
●
!
Do not connect to a PC when the "USB MODE" setting is set
to " ® ". See P.121 if you connect to PC by mistake.
1 Connect the cradle to the printer using the USB
cable.
2 Set the camera into the cradle.
●
!
The camera cannot be used to specify printer settings such
as the paper size and print quality.
●
!
Use an xD-Picture Card that was formatted on the camera.
1 Set the "USB/PLAY" switch on the cradle to the
"USB" position.
2 Press the "POWER" button on the cradle.
" " appears and then the menu is
s
displayed on the LCD monitor.
●
!
If the menu does not appear, check whether the "USB
" ".
®
MODE" setting is
●
!
Depending on the printer, some functions are disabled.
Continued
6
109