Table of Contents
Advertisement
Troubleshooting
Troubleshooting
Possible causes
The viewfinder lamp
i There is no battery in the camera.
does not light when
i The camera and AC power adapter are
charging the battery.
not connected correctly.
The viewfinder lamp
i The battery terminals are dirty.
blinks during charging
and the battery won't
charge.
i The battery can no longer be recharged.
No power.
i The battery has run out.
i The AC power adapter plug has come out
of the power outlet.
i The battery is loaded backward.
i The battery cover is not closed correctly.
Power cuts out during
The battery runs out.
operation.
Battery runs out quickly.
i Camera is being used in extremely cold
conditions.
i The terminals are soiled.
i The battery can no longer be recharged.
No photograph is taken
i No xD-Picture Card is inserted.
when the shutter button
i The xD-Picture Card is full.
is pressed.
i The xD-Picture Card is not formatted.
i The xD-Picture Card contact area is
soiled.
i The xD-Picture Card is damaged.
i The Auto power off function has turned the
camera off.
i The battery has run out.
Can't use the flash.
i The shutter button was pressed while the
flash was charging.
i The flash is not popped up.
i The Mode dial is set to "
i Continuous shooting is selected.
The flash settings are
The Mode dial is set to "
restricted and cannot be
/
"
".
selected.
Can
only
select
Continuous shooting is selected.
Suppressed flash mode.
Can only select the "
2
"
The Continuous shooting option is set to
™
and "
" quality settings.
"Long-period continuous shooting".
5
Can't select the "
",
The sensitivity is set to 800 (high-sensitivity
T
µ
≤
"
", "
" and "
"
photography).
quality settings.
The playback image is
i The subject is too far away.
dark even though the
flash was used.
i Your finger was covering the flash/flash
control sensor.
The image is blurred.
i The lens is dirty.
i You photographed scenery with Macro
mode selected.
i You took a close-up shot without selecting
Macro mode.
i You are shooting a subject that is not
suited to autofocusing.
There is speckling on
The picture was taken with a slow shutter
the image.
speed (long exposure) in a high-temperature
120
environment.
eIf you think the camera is faulty, check the following once more.
Solutions
i Load the battery.
i Connect the camera and AC power
adapter correctly.
i Take the battery out briefly and then
reload it.
i Wipe the battery terminals with a clean,
dry cloth.
i Load a new or fully charged battery. If the
battery still fails to charge, contact your
FUJIFILM dealer.
i Load a new or fully charged battery.
i Plug the adapter back in.
i Load the battery in the correct direction.
i Close the battery cover correctly.
Load a new or fully charged battery.
i Put the battery in your pocket or another
warm place to heat it and then load it into
the camera just before you take a picture.
i Wipe the battery terminals with a clean,
dry cloth.
i Load a new or fully charged battery.
i Insert an xD-Picture Card.
i Insert a new xD-Picture Card or erase
some unwanted frames.
i Format the xD-Picture Card on the
camera.
i Wipe the xD-Picture Card contact area
with a clean dry cloth.
i Insert a new xD-Picture Card.
i Turn the camera on.
i Load a new or fully charged battery.
i Wait until the flash has finished charging
before pressing the shutter button.
i Pop up the flash.
,
" Landscape.
i Change the Photography mode.
i Set continuous shooting to "OFF".
m
,
.
", "
", "
" or
The flash settings are restricted because the
camera settings are tailored to the scene
being shot. Change the Photography mode
for a wider range of flash settings.
Set continuous shooting to "OFF".
Set the Continuous shooting option to
something other than "Long-period
continuous shooting".
Set the sensitivity to 400 or less.
i Move to within the effective flash range
before taking the picture.
i Hold the camera correctly.
i Clean the lens.
i Cancel Macro mode.
i Select Macro mode.
i Use AF/AE lock to take the picture.
This is a characteristic of CCDs and does
not indicate a camera fault.
Troubleshooting
Possible causes
The camera does not
i The camera volume is set too low.
emit any sound.
i The microphone was blocked during
shooting/recording.
i There is something covering the speaker
during playback.
Frame erase does not
Some frames may be protected.
erase the frame.
The
ERASE
ALL
function does not erase
all the frames.
Screens
are
not
A language other than English is selected in
displayed in English.
the "
" setting in the "SET-UP"
menu (➡P.86).
There is no image or
i The included A/V cable was connected
sound on the TV.
during movie playback.
i The camera is not connected to the TV
correctly.
i "TV" is selected as the TV input.
i The video output setting is incorrect.
i The TV volume is turned down.
When the camera is
i The USB cable is not correctly connected
connected to a PC, the
to the PC or camera.
photographed image or
i The PC is not turned on.
playback image appears
on the camera's LCD
monitor.
Nothing happens when I
i Camera malfunction.
use the Mode dial.
i The battery runs out.
The camera no longer
The camera has suffered an unforeseen
works correctly.
problem.
Can't
print
with
"
®
" is not selected in USB mode in the
PictBridge.
"SET-UP" menu.
The
camera
was
connected to PC when
the USB mode was set
®
to "
".
Solutions
i Adjust the volume.
i Take care not to block the microphone
during shooting/recording.
i Make sure that the speaker is uncovered.
Unprotect frames using the camera on
which the protection was first applied.
1Press the "MENU/OK" button to display
the menu.
2Press "d" or "c" to select "
F
" and press
"a" or "b" to select "SET-UP". (Press the
"MENU/OK" button to display the SET-UP
screen on the LCD monitor.)
3Press "d" or "c" to move to option 4 and
then press "a " or "b " to select
"
".
4Press "d" or "c" several times to select
"ENGLISH".
5Press the "MENU/OK" button.
i After the movie playback mode is stopped,
connect the camera and TV correctly.
i Connect the camera and TV correctly.
i Set the TV input to "VIDEO".
i Change the setting to "NTSC" or "PAL"
(➡P.86).
i Adjust the volume.
i Set up the camera and the USB cable
(included) correctly.
i Turn the PC on.
i Briefly remove the battery or disconnect
the AC power adapter. Then reload the
battery or reconnect the AC power adapter
and try again.
i Load a new or fully charged battery.
Briefly remove the battery or disconnect the
AC power adapter. Then reload the battery
or reconnect the AC power adapter and try
again. If the message still appears, contact
your FUJIFILM dealer.
Select "
®
" in USB mode in the "SET-UP"
menu.
Perform steps 1 to 3 to remove the
camera from PC.
h Windows
1 The "New Hardware Found" wizard (or
"Scanner and Camera" wizard) appears.
If the wizard does not appear, proceed to
step 3.
2 Click the [Cancel] button.
3 Disconnect the camera from the PC.
h Macintosh
1 The window for locating the driver
appears. If the window does not appear,
proceed to step 3.
2 Click the [Cancel] button.
3 Disconnect the camera from the
Macintosh.
121
Hide quick links:
Advertisement
Table of Contents
