Image Display; Power Save Setting (Low Power Setting) - FujiFilm FinePix F610 Owner's Manual

SET–UP

IMAGE DISPLAY

ＳＥＴ−ＵＰ ＳＥＴ−ＵＰ １／３ １／３
ＩＭＡＧＥ ＤＩＳＰ． ＩＭＡＧＥ ＤＩＳＰ． ＯＮ ＯＮ
ＰＯＷＥＲ ＳＡＶＥ ＰＯＷＥＲ ＳＡＶＥ ２ ＭＩＮ ２ ＭＩＮ
ＦＯＲＭＡＴ ＦＯＲＭＡＴ ＯＫ ＯＫ
ＢＥＥＰ ＢＥＥＰ
ＳＨＵＴＴＥＲ ＳＨＵＴＴＥＲ
ＯＫ ＯＫ ＳＥＴ ＳＥＴ BACK BACK ＣＡＮＣＥＬ ＣＡＮＣＥＬ
ON : Photographed images are displayed for approx. 2 seconds and then automatically
recorded.
OFF : Photographed images are automatically recorded without being displayed.
PREVIEW : The results of your shot are shown as a preview (for image checking) and you can
then choose whether or not to record the image.
1Press "a" or "b" to zoom
3Press "a", "b", "d" or
"c" to panning
ＰＲＥＶＩＥＷ ＰＲＥＶＩＥＷ
2Switches between zoom and panning
1Press "d"or "c" to
check the images
ＰＲＥＶＩＥＷ ＰＲＥＶＩＥＷ
2Record all
72
You can use this setting to specify whether
photographed images are displayed after shooting.
G
!
In top5-frame continuous shooting, and final5-frame
continuous shooting, the images are displayed for a set time
before being automatically recorded even when "OFF" is
selected here.
Preview Zoom
When the "PREVIEW" setting is selected, this
function lets you enlarge images for detailed
checking.
1 Press "a" or "b" to zoom in or out.
2 The setting switches between "Zoom" and
"Panning" each time the " " button is pressed.
3 Press "a", "b", "d" or "c" to display another
part of the image.
G
!
You cannot save a cropped image from the preview screen.
G
!
Preview zoom works in the same way as the playback zoom
(➡P.29).
Continuous shooting preview ( image checking )
When the "PREVIEW" setting is selected, you can
check images shot in the top 5-frame continuous
shooting or final 5-frame continuous shooting modes.
However, you cannot use the preview zoom.
1 You can check the images by pressing "d" or
"c".
2 To record all the images, press the "
" button.
G
!
If you do not want to record any of the images, press the
" " button.
POWER SAVE SETTING ( low power setting )
ＳＥＴーＵＰ ＳＥＴーＵＰ １／３ １／３
ＩＭＡＧＥ ＤＩＳＰ． ＩＭＡＧＥ ＤＩＳＰ． ＯＮ ＯＮ
ＰＯＷＥＲ ＳＡＶＥ ＰＯＷＥＲ ＳＡＶＥ ２ ＭＩＮ ２ ＭＩＮ
ＦＯＲＭＡＴ ＦＯＲＭＡＴ ＯＫ ＯＫ
ＢＥＥＰ ＢＥＥＰ
ＳＨＵＴＴＥＲ ＳＨＵＴＴＥＲ
ＯＫ ＯＫ ＳＥＴ ＳＥＴ BACK BACK ＣＡＮＣＥＬ ＣＡＮＣＥＬ
In SET–UP and Playback modes, the function that automatically switches off the LCD monitor is
disabled. However, the camera still switches off automatically if it is left unused for a set time (2
minutes or 5 minutes).
N N
To restore power to the camera
When this function is enabled, the screen
temporarily switches off (The viewfinder lamp
(green) flashes at 1-second intervals.) to save power
if the camera is not used for approx. 30 seconds. If
the camera remains unused for an additional interval
(2 minutes or 5 minutes), it is automatically switched
off. Use this function when you want to get the
maximum possible running time from your battery.
G
!
The Power Save function is disabled during Auto Play and
when a USB connection is being used.
Pressing the Shutter button down halfway while the
viewfinder lamp (green) is blinking once a second
("FinePix" displayed on the display panel) restores
the camera to the fully active status (ready to
shoot). This is useful since the camera can be
ready to take pictures almost instantly.
G
!
You can wake the camera up by pressing any other button as
well as the Shutter button.
When the Power Save function has switched the
camera off, set the Power switch to OFF briefly and
then back to ON to switch the camera back on so
that it is ready to use.
73