TP-Link TD-W8960N User Manual

TP-Link TD-W8960N User Manual

300mbps wireless n adsl2+ modem router
Hide thumbs Also See for TD-W8960N:

Advertisement

TD-W8960N
300Mbps Wireless N ADSL2+ Modem Router
Rev: 4.0.0
1910010506

Advertisement

Table of Contents
loading

Summary of Contents for TP-Link TD-W8960N

  • Page 1 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router Rev: 4.0.0 1910010506...
  • Page 2 Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
  • Page 3: Fcc Statement

    FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
  • Page 4: Ce Mark Warning

    CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction...
  • Page 5: Declaration Of Conformity

    DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N ADSL2+ Modem Router Model No.: TD-W8960N Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:...
  • Page 6: Table Of Contents

    CONTENTS Package Contents ....................1 Chapter 1. Product Overview...................2 1.1 Overview of the Router ....................2 1.2 Main Features ........................3 1.3 Panel Layout ........................4 1.3.1 The Front Panel ........................4 1.3.2 The Back Panel........................5 Chapter 2. Connecting the Router................6 2.1 System Requirements ......................
  • Page 7 4.4.13 UPnP..........................60 4.4.14 Interface Grouping ......................61 4.4.15 LAN Ports........................... 63 4.4.16 IPSec..........................63 4.5 Wireless ......................... 67 4.5.1 Basic ..........................67 4.5.2 Security ..........................68 4.5.3 MAC Filter .......................... 85 4.5.4 Wireless Bridge ........................86 4.5.5 Advanced ........................... 87 4.5.6 Station info .........................
  • Page 8: Package Contents

    One power Adapter for TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router Quick Installation Guide One RJ45 cable Two RJ11 cables One ADSL splitter One Resource CD for TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router, including: • This User Guide • Other Helpful Information Note: Make sure that the package contains the above items.
  • Page 9: Chapter 1. Product Overview

    300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 1. Product Overview Thank you for choosing the TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router. 1.1 Overview of the Router The TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP.
  • Page 10: Main Features

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide 1.2 Main Features Complies with IEEE 802.11n to provide a wireless data rate of up to 300Mbps One RJ11 LINE port, four 10/100M Auto-Negotiation RJ45 LAN ports, supporting Auto MDI/MDIX Quick response semi-conductive surge protect circuit, reliable surge-protect function...
  • Page 11: Panel Layout

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide 1.3 Panel Layout 1.3.1 The Front Panel The Router’s LEDs are located on the front panel. Figure 1-1 The Router’s LEDs and the QSS button are located on the front panel (View from left to right).
  • Page 12: The Back Panel

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: 1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.3 Connecting the Router for more information about how to make Internet connection correctly. If you have...
  • Page 13: Chapter 2. Connecting The Router

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 2. Connecting the Router 2.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet). PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors. TCP/IP protocol on each PC.
  • Page 14 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 2-1...
  • Page 15: Chapter 3. Quick Installation Guide

    Wireless N ADSL2+ Modem Router using Quick Setup Wizard within minutes. 3.1 Configuring the PC After you directly connect your PC to the TD-W8960N or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC’s IP address. Follow the steps below to configure it.
  • Page 16 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3...
  • Page 17 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4 Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically”...
  • Page 18: Quick Installation Guide

    192.168.1.2 ~ 192.168.1.254. 3.2 Quick Installation Guide With a Web-based utility, it is easy to configure and manage the TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
  • Page 19 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-8 Note: 1) Do not mix up the user name and password with your ADSL account user name and password which are needed for PPP connections. 2) If the above screen does not pop up, it means that your Web-browser has been set to a proxy.
  • Page 20 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide values assigned by your ISP. Here we select PPPoE WAN Link Type for example, enter the Username and Password given by your ISP, and then click Next. Figure 3-10 Note: The Quick Setup Wizard will guide you to configure the WAN Service over ATM interface.
  • Page 21 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-11 Note: All the existed ATM&WAN service will be cleared after clicking the Save button on this Quick Setup page. You will see the Finish screen below, click Reboot to save these settings.
  • Page 22 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-13 You will see the current configuration has been added to Layer2 Interface list (4.4.1 Layer2 Interface) shown in Figure 3-14 and WAN Service list (4.4.2 WAN Service) shown in Figure 3-15.
  • Page 23: Chapter 4. Configuring The Router

    Software and Hardware. The second table displays the current status of the TD-W8960N connection. This information will vary depending on the settings of the Router configured on the Advanced Setup screen.
  • Page 24: Quick Setup

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-1 Note: Click the other submenus under the main menu Device Info, and you will be able to view the corresponding information about WAN, Statistics, Route, ARP and DHCP. 4.3 Quick Setup Please refer to Section 3.2 Quick Installation...
  • Page 25: Layer2 Interface

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide This Advanced Setup section mainly introduces how to configure the Router for adequate use. The detailed explanations for each subsection are provided below. Note: To completely configure the WAN Interface, you need to first select the Layer2 Interface (4.4.1...
  • Page 26 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-2 Remove: Select the check box in the table on the screen above and then click the Remove button, the corresponding interface will be deleted in the table. Note: If the interface is used by the configuration of the 4.4.2 WAN...
  • Page 27 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-3 VPI/VCI: the VPI and VCI values provided by your ISP. Do not change them unless it was required by your ISP. DSL Link Type: Select a DSL Link Type which is provided by your ISP. The options include EoA (it is for PPPoE, IPoE, and Bridge), PPPoA (PPP over ATM) and IPoA (IP over ATM).
  • Page 28 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide this, it cannot be set for the connection type of CBR and Real-time VBR. If you select the QoS service, the Quality of Service menu will be added to the Web-based Utility, the detailed configuration will be described in 4.4.8 Quality of Service.
  • Page 29: Wan Service

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-6 Remove: Select the check box in the table on the screen above and then click the Remove button, the corresponding interface will be deleted in the table. Note: One ETH is allowed to configure as the layer 2 WAN Interface.
  • Page 30 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: 1) The following section adopts different VPI, VCI to introduce further configuration for the different connection types, if you need to change the configuration of ATM PVC (VPI/VCI), you should go to the previous section (4.4.1 Layer2...
  • Page 31 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Enter the following parameters and then click Next. Figure 4-10 PPP Username/Password: Enter the User Name and Password provided by your ISP. These fields are case-sensitive. PPPoE Service Name: Enter the Service Name if it was provided by your ISP. If you leave it blank, the default name will be the same as the Service Description on the previous screen.
  • Page 32 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide PC, and the NAT and SPI Firewall will be closed. Sometimes you can think it as bridge while PPP dialing in the router. It’s a special feature deployed by some ISP. Unless your ISP specifically requires this setup, do not select it.
  • Page 33 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: If only single PVC with IPoA is configured, you must enter static DNS server IP addresses. On the next screen you will see the detailed settings you’ve made. Please click the Apply/Save button to save these settings.
  • Page 34 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.2.2 ATM-EoA-IPoE If your ISP provides an IPoE connection and you need to use an ATM Interface, follow the steps below to add a WAN service over a selected ATM interface: Add a new ATM interface and select EoA option for DSL Link Type (4.4.1.1 ATM...
  • Page 35 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Alternatively, the device may use IAID value 1 for the virtual circuit corresponding to the first connection object in the data model and value 2 for the second connection object in the data model.
  • Page 36 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Select a preferred WAN interface as the system default gateway and click Next. Figure 4-17 Configure the DNS Server Addresses on the screen as follows. Figure 4-18 Note: If only single PVC with IPoA is configured, you must enter static DNS server IP addresses.
  • Page 37 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-19 4.4.2.3 ATM-EoA-Bridging If you want to adopt the Bridge service and you need to use an ATM Interface, follow the steps below to add a WAN service over a selected ATM interface: Add a new ATM interface and select EoA option for DSL Link Type (see 4.4.1.1 ATM...
  • Page 38 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.2.5 ATM-IPoA If your ISP provides an IPoA connection and you need to use an ATM Interface, follow the steps below to add a WAN service over a selected ATM interface.
  • Page 39: Lan

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-20 4.4.3 LAN Choose “Advanced Setup” “LAN”, and you will see the LAN screen (shown in Figure 4-21), the section allows you to configure the Router’s LAN ports settings.
  • Page 40 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-21 IP Address: You can configure the Router’s IP Address and Subnet Mask for LAN Interface. • IP Address: Enter the Router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1.
  • Page 41: Mac Clone

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide • Start IP Address: Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the Router is 192.168.1.1, the default Start IP Address is 192.168.1.2, and the Start IP Address must be 192.168.1.2 or greater, but...
  • Page 42: Nat

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Service for the interface on the section 4.4.2 WAN Service, the blank for MAC Address will display “Need a corresponding WAN Service”. The last one of WAN Interface List displays your PC’s current address.
  • Page 43 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-24 4.4.5.1 Virtual Servers Choose “Advanced Setup” “NAT” “Virtual Servers”, you can set up virtual servers on the screen below (shown in Figure 4-25). Virtual servers can be used for setting up public services on your LAN, such as DNS, Email and FTP.
  • Page 44 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Remove: Select the check box in the table (shown in Figure 4-25) and then click the Remove button, then the corresponding entry will be deleted in the table. To add a virtual server entry: Click the Add button on the preceding screen Figure 4-25, and then you will see the new Virtual Server in the next screen as shown in Figure 4-26.
  • Page 45 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: If you select the service from the drop-down list, the External Port Start, External Port End, Internal Port Start, Internal Port End and the Protocol will be added in the table automatically. You only need to enter the Server IP Address for the Virtual Server.
  • Page 46 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-28 Select the application from the drop-down list. If the list does not have the application that you want, select the Custom application radio button, and type the name of the custom application in the text box.
  • Page 47: Security

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-29 To add a new DMZ Host: You can enter the computer's IP address and then click Save/Apply to activate the DMZ host you set on this page. Note: DMZ host forwards all the ports at the same time. Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP Address assigned to it because its IP Address may change while using the DHCP function.
  • Page 48 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide The Outgoing IP Filtering feature allows you to control some IP traffic from LAN to access to some specifically addresses. By default, all outgoing IP traffic from LAN is allowed, but some IP traffic can be BLOCKED by setting up filters.
  • Page 49 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: When you add an Outgoing IP Filtering entry, you must configure at least one condition on the preceding screen except the Filter name. If you leave the Protocol blank, it means that the rule is...
  • Page 50 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-34 Enter the Filter name for the rule, it is exclusive and must be filled in. Select Protocol in the drop-down list, enter Source IP address, Source Subnet Mask, Source Port, Destination IP address, Destination Subnet Mask, and Destination Port for the rule.
  • Page 51 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-35 Change Policy: There are two policies for the MAC filters: FORWARDED and BLOCKED. Select the Change checkbox and click the Change Policy button to change from one policy to another. When you set FORWARDED, it means that all MAC layer frames will be forwarded except those matching with any of the specified rules in the table (shown in Figure 4-35).
  • Page 52: Parental Control

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-36 Select Protocol Type in the drop-down list for the rule. Enter Destination MAC Address and Source MAC Address in the text box. Select Frame Direction in the drop-down list for the rule.
  • Page 53 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-38 To add a Time Restriction entry: Click the Add button in Figure 4-38, and then you will see the next screen as shown in Figure 4-39. Figure 4-39 Enter the User Name of the LAN device connected to the Router.
  • Page 54 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: The Time Restriction will not work correctly before the time of the device is set in “Management Internet Time”. 4.4.7.2 URL Filter This feature allows you to configure the filter rules based on URL to control all the computers in the LAN to access the specified port, and it is independent with Time Restriction feature.
  • Page 55: Quality Of Service

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.8 Quality of Service Choose “Advanced Setup” “Quality of Service”, you can enable QoS (Quality of Service) on the screen shown in Figure 4-42. QoS helps to prioritize data as it enters your router. By attaching special identification marks or headers to incoming packets, QoS determines which queue the packets enter, based priority.
  • Page 56 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-43 Click the Add button in Figure 4-43, and you can configure the QoS queue entry on the next screen as shown in Figure 4-44. Figure 4-44 Name: Set a name for the entry.
  • Page 57 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: Lower integer values for precedence imply higher priority for this queue relative to others. The queue entry configured here will be used by the classifier to place ingress packets appropriately.
  • Page 58: Traffic Control

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-46 After you specify the condition, click Save/Apply to save the entry. 4.4.9 Traffic Control Choose “Advanced Setup” “Traffic Control” and then you will see the screen as shown in Figure 4-47.
  • Page 59 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Enable: Check this box to enable the Traffic Control function. Egress Total Rate (Kbps): Enter the upload speed through the WAN port. Ingress Total Rate (Kbps): Enter the download speed through the WAN port.
  • Page 60 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-49 Rule Status: Select the status of the rule from the drop-down list to enable or disable the rule. IP Range: Enter a single IP address or a range of IP addresses.
  • Page 61: Routing

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide there still has surplus bandwidth, it is allocated to the rule with hypo-high precedence. For rules with the same precedence, the surplus bandwidth is allocated to them according to their min egress/ingress rate.
  • Page 62 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: 1) If changing the Automatic Assigned Default Gateway from unselected to selected, you have to reboot the Router to get the automatically assigned default gateway. 2) Default Gateway IP address should be specified since MER Interface is selected when you select the Enable automatic Assigned Default Gateway check box.
  • Page 63 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Use Interface: Select the Interface name in the text box, or else, the default Use Interface will be adopted for the Static Route. Use Gateway IP Address: If you select the IPoE or IPoA mode for Use Interface, the screen above will display this item, you should type the Gateway address correctly, and the other option for Use Interface will adopt the default Gateway address for the Static Route.
  • Page 64: Dns

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.11 DNS When you select the connection type PPPoE, PPPoA or IPoA for WAN configuration, you will see the DNS menu in the Web-based Utility (shown in Figure 4-56). It includes DNS Server and Dynamic DNS submenus.
  • Page 65 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide For single PVC with IPoA, static IPoE protocol, please select the Use the following Static DNS IP address checkbox, and enter the primary and /or optional secondary DNS server IP addresses provided by your ISP.
  • Page 66: Dsl

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-59 Select D-DNS provider in the drop-down list. Enter the Hostname of the DNS Server, and select the corresponding Interface for the DDNS, you can leave it default. Type the User Name and Password for your DDNS account.
  • Page 67: Upnp

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-60 You can select the modulation type, phone line pair and the capability of Bitswap or SRA. After you set them up, click Save/Apply to save the configurations. 4.4.13 UPnP Choose “Advanced Setup”...
  • Page 68: Interface Grouping

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-61 Select the checkbox and click Save/Apply to enable the UPnP function. 4.4.14 Interface Grouping Choose “Advanced Setup” “Interface Grouping”, you can configure multiple ports to PVC and bridging groups to perform as an independent network.
  • Page 69 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide To create a new interface group: Click the Add button. You can add a new interface group in the next screen. Figure 4-63 Enter a unique name for Group. Select the Interface which you want to use from the drop-down list.
  • Page 70: Lan Ports

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Select interfaces from the available interface list and add it to the grouped interface list using the arrow buttons to create the required mapping of the ports. Note: These clients may obtain public IP addresses.
  • Page 71 Note: You could also use other VPN Routers to set VPN tunnels with TD-W8960N. TD-W8960N supports up to 10 VPN tunnels simultaneously. Click Add New Connection in Figure 4-65 and then you will enter the screen shown in Figure...
  • Page 72 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-66 IPSec Connection Name: Enter a name for your VPN. Remote IPSec Gateway Address (IP or Domain Name): Enter the destination gateway IP address in the box which is the public WAN IP or Domain Name of the remote VPN server endpoint.
  • Page 73 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Pre-Shared Key: Input the Pre-Shared key for Authentication. (For example: Input 12345678) Perfect Forward Secrecy: PFS is an additional security protocol. We recommend you leave the Advanced Settings as default value.
  • Page 74: Wireless

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Key Life Time: Enter the number of seconds for the IPSec lifetime. It is the period of time to pass before establishing a new IPSec security association (SA) with the remote endpoint. The default value is 3600.
  • Page 75: Security

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide This page allows you to configure basic features of the wireless LAN interface. You can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on Region requirements.
  • Page 76 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-68 4.5.2.1 QSS (WPS) Setup Back to LED Explanation This section will guide you to add a new wireless device to an existing network quickly by QSS (Quick Security Setup) method. It’s also called WPS (Wi-Fi Protected Setup) in some cases.
  • Page 77 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-69 Method One: Hardware push button. Step 1: Press the QSS button on the front panel of the Router. Step 2: Press and hold the QSS button of the adapter directly for 2 or 3 seconds.
  • Page 78 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-70 Method Two: Step 1: Press the QSS button on the front panel of the Router. Step 2: For the configuration of the wireless adapter, please choose “Push the button on my access point”...
  • Page 79 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 3: Wait for a while until the next screen appears. Click Finish to complete the QSS configuration. Figure 4-72 II. By PIN If the new device supports Quick Security Setup and the PIN method, you can add it to the network by PIN with the following two methods.
  • Page 80 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-73 Note: The PIN code of the adapter is always displayed on the QSS configuration screen. Step 2: For the configuration of the wireless adapter, please choose “Enter a PIN into my access point or a registrar”...
  • Page 81 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-74 Note: In this example, the default PIN code of this adapter is 16952898 as the preceding figure shown. Method Two: Enter the PIN of my Router into the wireless adapter.
  • Page 82 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-75 Step 2: For the configuration of the wireless adapter, please choose “Enter a PIN from my access point” in the configuration utility of the QSS as below, and enter the PIN code of...
  • Page 83 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-76 4.5.2.2 Manual Setup AP Follow the instructions below to configure security features of the wireless LAN interface manually. You can set the network authentication method, select data encryption, specify whether a network...
  • Page 84 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-77 Network Authentication: Select an authentication type from the drop-down list. Options available are: Open, Shared, WPA, WPA-PSK, WPA2, WPA2-PSK, Mixed WPA2/WPA, and Mixed WPA2/WPA-PSK. Note: For most users, it is recommended to use the default Wireless LAN Performance settings. Any changes made to these settings may adversely affect your wireless network.
  • Page 85 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide below to configure the Shared Keys. Figure 4-78 Figure 4-79...
  • Page 86 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Encryption strength: Select the appropriate level of encryption, 64-bit or 128-bit. Current Network Key: To indicate which WEP key to use, select a transmission key number. Network Key 1-4: If you want to manually enter the WEP keys, then enter them in the network Key 1-4 fields.
  • Page 87 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide WPA security for wireless communication has been developed to overcome some of the shortcomings of WEP. WPA combines the key generation with the authentication services of a RADIUS server. Figure 4-81 WPA Group ReKey Interval: Enter the Key Renewal period, which tells the Router how often it should change encryption keys.
  • Page 88 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-82 WPA-PSK WPA-PSK requires a shared key and does not use a separate server for authentication. PSK keys can be ASCII or Hex type. Figure 4-83 WPA Pre-Shared Key: Enter the key shared by the Router and your other network devices. It must have 8-63 ASCII characters or 64 Hexadecimal digits.
  • Page 89 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Configure WPA-PSK settings 1. Select WPA-PSK. The menu will change to offer the appropriate settings as the picture show above. 2. WPA-PSK requires a shared key. Type the key in the space provided. PSK keys can be ASCII or Hex type.
  • Page 90 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-86 WPA2 Preauthentication: Select Enable from the drop-down list, Stations will authenticate with the AP during the scanning process, and once association is required, the station has been already authenticated.
  • Page 91 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Mixed WPA2/WPA To configure Mixed WPA2/WPA settings, select the Mixed WPA2/WPA option from the drop-down list. The menu will change to offer the appropriate settings. The steps to these settings are similar to those for WPA-PSK.
  • Page 92: Mac Filter

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.3 MAC Filter Choose “Wireless” ”MAC Filter”, you will see the screen of Wireless--MAC Filter settings shown as below. Figure 4-90 Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s RADIUS.
  • Page 93: Wireless Bridge

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.4 Wireless Bridge Choose “Wireless” ”Wireless Bridge”, you will see the screen of Wireless--Bridge settings shown as below. You can configure wireless bridge features of the wireless LAN interface and click Apply/Save button to save the current configuration.
  • Page 94: Advanced

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide • Enabled (Scan): Select this option to enables wireless bridge restriction, and it will scan the environment for APs that exist around the device. Only those selected AP will be granted access.
  • Page 95 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-95 Channel: Select the channel you want to use from the drop-down List. This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.
  • Page 96: Station Info

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Interval value. Its clients hear the beacons and awaken to receive the broadcast and multicast messages. The default value is 1. Beacon Interval: Enter a value between 20-1000 milliseconds. The Beacon Interval value indicates the frequency interval of the beacon.
  • Page 97: Management

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-97 4.7 Management Choose “Management”, there are eight submenus under the main menu. They are Settings, System Log, SNMP Agent, TR-069 Client, Access Control, Update Software and Reboot. Click any of them, and you will be able to configure the corresponding function.
  • Page 98 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-98 4.7.1.1 Export Choose “Management” “Settings” “Export”, you can see the Export screen, this screen (shown in Figure 4-99) allows you to save the current configuration of the Router as a backup file.
  • Page 99 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8960N Figure 4-101 4.7.1.2 Import Choose “Management” “Settings” “Import”, you can see the Import screen, this screen (shown in Figure 4-102) allows you to update the Router’s settings. Figure 4-102 To update the Router’s settings: Click the Browse button to locate the update file for the device, and you can also enter the exact path to the Setting file in the text box.
  • Page 100: System Log

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.7.1.3 Restore Default Choose “Management” “Settings” “Restore Default”, you can see the Restore Default screen, this screen (shown in Figure 4-103) allows you to restore the Router’s configuration to the factory defaults on the screen.
  • Page 101 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-105 Refresh: Click the button, the information in the table will be updated. Close: Click the button, the screen will be closed. To Configure the System Log Settings: Click the Configure System Log button (shown in Figure 4-104), you will see the screen below (shown in Figure 4-106).
  • Page 102: Snmp Agent

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.7.3 SNMP Agent Choose “Management” “SNMP Agent”, you can see the SNMP-Configuration screen as shown below. SNMP (Simple Network Management Protocol) has been widely applied in the computer networks currently, which is used for ensuring the transmission of the management information between any two nodes.
  • Page 103: Client

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide System Name: Enter alphanumeric string to specify an SNMP community string name. Your Router (SNMP agents) will expose management data on the managed systems as this "system name". System Location: The person to notify when problems occur.
  • Page 104: Access Control

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide WAN Interface used by TR-069 Client: Please select the WAN Interface from the drop-down list to perform this function. Connection Request User Name: Type the Connection Request User Name, set it yourself.
  • Page 105: Update Firmware

    Update Firmware: After you have selected the latest software, click the button. To update the Router's software: Download the latest software upgrade file from the TP-LINK website (http://www.tp-link.com). Click Browse to view the folders and select the image file or enter the exact path to the image file location in the text box.
  • Page 106: Reboot

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.7.7 Reboot Choose “Management” “Reboot”, you can see the screen (shown in Figure 4-111) which allows you to reboot the Router. Figure 4-111 Note: After you clicked the Reboot button, please wait for a while before reopening your web browser.
  • Page 107: Appendix A: Faq

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Appendix A: FAQ How do I configure the Router to access Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the WAN port on the Router. The telephone cord plugs into the Line port of the ADSL Modem.
  • Page 108 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: Your opposite side should call your WAN IP, which is displayed on the “Status” page. 4) How to enable DMZ Host: Log in to the Router, click the “Advanced Setup-NAT” menu on the left of your browser, and click "DMZ Host"...
  • Page 109 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide the "Virtual Servers" submenu. On the "Virtual Servers" page, click Add New, then on the “Add or Modify a Virtual Server” page, enter use “80” as service port, and your IP address next to the “Server IP Address”, assuming 192.168.1.188 for an example, and remember to click the...
  • Page 110: Appendix B: Configuring The Pc

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Appendix B: Configuring the PC For Windows XP OS Go to Start > Control Panel, you will then see the following page. Click Network and Internet Connections Click Network Connections Right-click Local Area...
  • Page 111 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Double-click Internet Protocol (TCP/IP) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK...
  • Page 112 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Click OK...
  • Page 113 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide For Windows Vista OS Go to Start > Settings >Control Panel, and then you will see the following page. Click View network status and tasks Click View status Click Properties...
  • Page 114 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK...
  • Page 115 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide For Windows 7 OS Go to Start > Settings > Control Panel, and then you will see the following page. Click View network status and tasks Click Change adapter settings Right-click Local...
  • Page 116 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK...
  • Page 117: Appendix C: Specifications

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Appendix C: Specifications General ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5, Standards IEEE 802.3, IEEE 802.3u, IEEE 802.11b , IEEE 802.11g , 802.11n Protocols TCP/IP, IPoA , PPPoA , PPPoE, SNTP, HTTP, DHCP, ICMP, NAT LAN Ports: Four 10/100M Auto-Negotiation RJ45 ports(Auto MDI/MDIX)
  • Page 118: Appendix D: Glossary

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Appendix D: Glossary 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding.
  • Page 119 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (e.g., www.xyz.com) and a dynamic IP address. Default Gateway - A device that forwards Internet traffic from your local area network.
  • Page 120 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide LAN - The computers and networking products that make up your local network. MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking device. NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different IP address for the Internet.
  • Page 121 TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Static Routing - Forwarding data in a network via a fixed path. Subnet Mask - An address code that determines the size of the network. TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement from the recipient of data sent.
  • Page 122: Appendix E: Technical Support

    TD-W8960N 300Mbps Wireless N ADSL2+ Modem Router User Guide Appendix E: Technical Support Technical Support For more troubleshooting help, go to: www.tp-link.com/support/faq.asp To download the latest Firmware, Driver, Utility and User Guide, go to: www.tp-link.com/support/download.asp For all other technical support, please contact us by using the following details: Global Australia &...

Table of Contents