Wiring Connections - Viking AES--2000 Technical Practice

C. Wiring Connections
Two POTs are provided to
increase or decrease speak-
er volume and microphone
sensitivity. In certain noisy
locations the speaker volume
can be increased and the
microphone sensitivity may
need to be decreased as
shown.
Relay Contact Specs:
5A @ 30VDC/250V AC
Note: Gate controllers do not
typically require power.
Once the AES-2000 is secured to the wall, the unit can be connected to the building wiring as described below.
Step 1. Cut off the 2.1 mm plug from the end of the AC power adapter cord. The AC adapter can be located up to 100 feet away from the entry
system when using a minimum of 24 AWG wire.
Step 2. Make all connections to the AES-2000 panel before inserting the adapter into a wall outlet. The two wires from the AC adapter connect
to the two terminal block positions labeled "13.8 VAC".
Step 3. If the incoming telephone line has an RJ-11 connector, connect it to the RJ-11 jack on the control board. Two terminal positions
marked "C.O." are also provided for a striped wire connection.
Step 4. The AES-2000 can be wired to operate a single door strike, or a door strike and an automatic door opener. The doorstrike and door
strike power supply should be wired to the terminal positions labeled "Door Strike 1". Both normally open and normally closed contacts
are available.
Step 5. If your automatic door requires a contact closure for activation, wire it to the terminal positions labeled "Door Strike 2". Both normally
open and normally closed contacts are available.
Step 6. If the installation requires a postal lock, a normally open momentary key switch can be wired to the terminal block positions labeled
"Postal Lock".
Step 7. If a C-3000 is to be used, connect a pair of wires from the AES-2000 terminal block labeled "C-3000" to the C-3000 entry phone
connection. The phone numbers for the lines wired to the C-3000 must have a "C" programmed as the first character (see
Programming). For more information, see DOD# 162 and 868.
Step 8. After all the connections are made, close and lock the hinged panel.
Step 9. The last step is to connect the A.C. power adapter to a wall outlet. When power is connected to the system, the front display should
show
The tenant names and phone numbers must be programmed into the system for prop-
er operation. This programming is done through the telephone line interface using the
PB-100 with special software. This allows either remote programming from a distant
location, or local programming using the Viking DLE-300 line simulator. The PB-100
is connected to a serial port of a P.C. and Windows based software is used to enter
tenant names, phone numbers and the recording for the voice directory. A data base
is constructed for each apartment to make future changes easier. When the Remote
Programmer software is first invoked, the screen at the right pops up. After a few sec-
onds, the "Building Selection" screen will appear.
The following sections provide a brief overview of programming screen shots and
descriptions. Detailed programming instructions are available only in the software
itself.
Audio Detect DIP Switches
ON
OFF
C.O. Line
To C-3000
or Analog
PABX/KSU
station
Doorstrike/Magnetic Lock #1
Normally Open Relay Contact
- or -
Normally Closed Relay Contact
Sw 2
Sw 1
ON
ON
ON
OFF
OFF
1 2
J4 J4
J12 J12
1 1
ON
S1
1 2
Microphone
1
Speaker
Volume
R12 R12 R39 R39
- +
8 1
1
Normally Closed Relay Contact
Normally Open Relay Contact
Doorstrike/Magnetic Lock #2
J10
1
1
Description
J2 J2
J2 J2
10 10
Volume
1 6
13.8V AC
120V AC
Adapter
included
Keyed Momentary or
Relay Contact Specs:
Postal Lock with
5A @ 30VDC/250V AC
Momentary Switch
Note: Gate controllers do not
- or -
Rear View
of the
AES-2000
AES-NET
Wiegand/CAN
Network Interface
included
typically require power.
5