Auxiliary Device
(Optional)
Operating Auxiliary Devices (Optional)
To operate your devices connected to the AUX terminals on the rear
panel of IVA-W505R/IVA-W502R (AUX mode) or to the iPod Direct
connector by using iPod Direct/RCA Interface cable (sold separately)
(AUX+ mode), follow the procedure described below.
WARNING
It is dangerous (and illegal in many states) for the
driver to watch the TV/Video while driving the vehicle.
The driver may be distracted from looking ahead and
an accident could occur.
Install the IVA-W505R/IVA-W502R correctly so that the
driver cannot watch TV/Video unless the vehicle is
stopped and the emergency brake is applied.
If the IVA-W505R/IVA-W502R is not installed correctly,
the driver will be able to watch the TV/Video while
driving the vehicle and may be distracted from
looking ahead and cause an accident. The driver or
other people could be severely injured.
• If you try to activate the auxiliary device while driving, the display
will show the warning-PICTURE OFF FOR YOUR SAFETY.
1
Touch [SOURCE] on the main source screen.
The source screen appears on the display.
2
1
Touch [AUX]*
or [AUX+]*
The external input screen is displayed.
3
Touch [NTSC/PAL] to change the video input.
4
Touch [COMP./S-VIDEO]*
signal input mode.
The mode switches with each touch.
1
*
The name which is given as the source name in "Setting the AUX
Mode" on page 40 is displayed.
2
*
The mode which is given as the source name in "Setting the AUX+
Mode" (page 41).
3
*
The video signal can be input in two ways, selecting the right mode
depending on the connection method.
• If the AUX mode is not displayed on the main menu, set AUX IN to
ON by following "Setting the AUX Mode" (page 40).
• The setting of switching NTSC/PAL, which you have set in this
section, can be used in same way in "Switching the Visual Input
Signal System" on page 40.
• The display mode changes by touching [WIDE].
For operation, refer to "Switching Display Modes" on page 29.
• After connecting the KCA-410C, its AUX input can be used only in
INTERRUPT MODE. For details, refer to the KCA-410C Owner's
Manual.
• Switching to the COMP. mode when using the Video Input Connector.
Switching to the S-VIDEO mode when using the S Video Input
Connector.
58
-EN
2
.
3
to switch the video
TUE-T200DVB
Operation (Optional)
Operating the TUE-T200DVB (Optional)
Operable when optional TUE-T200DVB is connected.
When DVB-T is selected in "Setting the AUX Mode" (page 40), the
source is displayed in SOURCE selection screen.
1
While your vehicle is parked, touch [SOURCE] on
the main source screen.
The source screen appears on the display.
2
Touch [DVB-T].
The DVB-T screen is displayed.
3
Perform the desired operation.
Channel Number Up/Down or Favorite Channel Number
Up/Down
Touch [CH.]
to select changing the Channel or the
*
Favorite Channel.
Touch CH. [
] or [ ] to move the Channel number Up/Down.
Touch FAV [
] or [ ] to move the Favorite Channel number Up/
Down.
* The button displays the current changing mode ([CH.] or [FAV]).
Calling up Main Menu Screen
Touch [MENU] to call up the main menu screen.
Calling up Menu Operation Mode
1
Touch [P1/2].
The function guide appears.
2
Touch [MENU CONT] to call up the menu operation
mode.
Switching the Source
Touch [BAND].
The source switches with each touch.
Calling up Electronic Programme Guide (EPG)
Touch [EPG] to call up the Electronic Programme Guide.
Scanning Mode
1
Touch [P1/2].
The function guide appears.
2
Touch [A.MEMO] to start the auto scan procedure.
• For detail, refer to the Owner's Manual of the TUE-T200DVB sold
separately.
Switching the Video Input Mode
Touch [COMP./S-VIDEO].
The video signal input mode switches with each touch.
• Switching to the COMP. mode when using the Video Input Connector.
Switching to the S-VIDEO mode when using the S Video Input
Connector.