Search Function - Alpine IVA-W505R Owner's Manual

Adjusting the Balance/Fader Directly
C
Touch and move [ ] to a desired setting.
Or touch a desired setting range, and [
location.
Touch [L] or [R] of Balance and [F] or [R] of Fader for fine-tuning.
Turning Defeat ON or OFF
Touch [ ] to display the DEFEAT adjusting screen.
Touch [ ] or [ ] of DEFEAT to set to ON or OFF.
If you set the defeat to ON, MX of an external audio processor is
turned OFF and EQ is returned to the initial setting.
Adjusting NAV. MIX Level
Touch [ ] or [ ] of NAV. MIX LEVEL to adjust the
volume of navigation interruption.
Setting range: 0 to 15
• This adjustment becomes available when NAV. MIX is turned on in
"Setting the Navigation Interruption" (page 40).
• The setting navigation interruption is not displayed if an external
audio processor not compatible with NAV. MIX is connected.
Adjusting the Subwoofer Level
Touch [ ] or [ ] of SUBWOOFER to set the subwoofer
ON/OFF.
Touch [ ] to display the SUBWOOFER output adjusting screen
after setting the SUBWOOFER to ON.
Touch [ ] or [ ] to adjust the SUBWOOFER output.
Setting range: 0 to 15
• When an external processor is connected, the display changes from
"SUBWOOFER" to the "SUBW. LV" item. You can change the
subwoofer output level between 0 and 15 by touching [ ] or [ ].
• The SUBWOOFER SYSTEM, SUBWOOFER PHASE and
SUBWOOFER CHANNEL may be set when an optional IMPRINT
audio processor (PXA-H100) is connected, SUBWOOFER is set to
ON, and MultEQ OFF mode is selected. For details, refer to "Setting
the Subwoofer" on page 53.
Adjusting H.P.F. (Highpass Filter)
Touch [ ] to display the H.P.F. adjusting screen.
Touch [ ] or [ ] of the desired speaker.
Setting range: OFF, 80 Hz, 120 Hz, 160 Hz
• Select OFF when no adjustment is required.
• When an external processor or IMPRINT audio processor
(PXA-H100) is connected, the display changes from "H.P.F." to the
"A.PROCESSOR" item. For "A.PROCESSOR" operation, refer to
"External Audio Processor (Optional)" on page 44 or "IMPRINT
Operation (Optional)" on page 50.
Adjusting Bass/Treble
You can change the bass/treble frequency emphasis to
create your own tonal preference.
Touch [ ] to display the Bass/Treble adjusting screen.
Touch [ ] or [ ] on the scroll bar to scroll the setup items line
by line.
• Adjustment cannot be performed when an external audio processor is
connected and DEFEAT is set to ON.
Setting the Bass level
You can emphasize or weaken the bass frequency.
Touch [ ] or [ ] of BASS LEVEL to select the desired bass
level.
Setting range: –7 to +7
28
-EN
Setting the Bass Centre Frequency
The displayed bass frequency is emphasized.
] will move to that Touch [ ] or [ ] of BASS FREQ to select the desired bass
centre frequency.
Setting the Bass Bandwidth
Changes the boosted bass bandwidth to wide or narrow.
A wider setting will boost a wide range of frequencies
above and below the centre frequency. A narrower
setting will boost only frequencies near the centre
frequency.
Touch [ ] or [ ] of BASS BANDWIDTH to select the desired
bass band width.
• The bass level settings will be individually memorized for each
Setting the treble level
You can emphasize the treble frequency.
Touch [ ] or [ ] of TREBLE LEVEL to select the desired treble
level.
Setting the Treble Centre Frequency
The displayed treble frequency is emphasized.
Touch [ ] or [ ] of TREBLE FREQ to select the desired treble
centre frequency.
• The treble level settings will be individually memorized for each
Setting the Loudness
Loudness introduces a special low- and high-frequency
emphasis at low listening levels. This compensates for
the ear's decreased sensitivity to bass and treble sound.
Touch [ ] or [ ] of LOUDNESS to set to ON or OFF.

Search Function

1
Select a desired track or folder
Setting range: 60 Hz, 80 Hz, 100 Hz, 200 Hz
Setting range: WIDE1 to WIDE4
source (FM, MW, LW, CD, etc.) until the setting is changed. The bass
frequency and bass bandwidth settings adjusted for one source are
effective for all other sources (FM, MW, LW, CD etc.).
Setting range: –7 to +7
Setting range:10 kHz, 12.5 kHz, 15 kHz, 17.5 kHz
source (FM, MW, LW, CD, etc.) until the setting is changed. The
Treble frequency settings adjusted for one source are effective for all
other sources (FM, MW, LW, CD, etc.).
Touch [ ] on the function guide while in the CD,
MP3/WMA/AAC or DivX
Search list screen is displayed.
Touch [ ] for direct playback.
When a hierarchical list is prepared, [
displayed. Touch [ ] to display the respective
hierarchy list screens.
®
mode.
] will be