1. Manuals
  2. Brands
  3. Ford Manuals
  4. Automobile
  5. 2000 Escort
  6. Owner's manual

Ford 2000 Escort Owner's Manual

Ford motor company escort owner's guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Before driving
Starting and driving
Servicing
All rights reserved. Reproduction by any means, electronic or mechanical including
photocopying, recording or by any information storage and retrieval system or translation
in whole or part is not permitted without written authorization from Ford Motor Company.
Ford may change the contents without notice and without incurring obligation.
Copyright © 1999 Ford Motor Company
Contents
2
6
16
60
84
89
105
125
175
182
193
194
1

Advertisement

Table of Contents
loading

Related Manuals for Ford 2000 Escort

Summary of Contents for Ford 2000 Escort

  • Page 1: Table Of Contents

    All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.

  • Page 2: Introduction

    Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning Engine exhaust, some if its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm. ICONS Indicates a safety alert.
  • Page 3 INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.

  • Page 4: Vehicle Symbol Glossary

    Introduction These are some of the symbols you may see on your vehicle. Safety Alert Fasten Safety Belt Air Bag-Side Child Seat Installation Warning Brake System Brake Fluid - Non-Petroleum Based Master Lighting Switch Fog Lamps-Front Fuel Pump Reset Windshield Defrost/Demist Power Windows Front/Rear...
  • Page 5 Child Safety Door Lock/Unlock Panic Alarm Engine Coolant Do Not Open When Hot Avoid Smoking, Flames, or Sparks Explosive Gas Power Steering Fluid Emission System Passenger Compartment Air Filter Vehicle Symbol Glossary Interior Luggage Compartment Release Symbol Engine Oil Engine Coolant Temperature Battery Battery Acid...

  • Page 6: Instrumentation

    Instrumentation Instrument cluster Foglamp control * (pg. 8) (pg. 42) Headlamp/ turn signal control (pg. 41) THEFT RPMx1000 0 0 0 1 1 3 FUEL FILL FUEL MIRROR Power side view mirrors* (pg. 17) Speed control* (pg. 43) Driver air bag (pg.

  • Page 7: Climate Controls

    Windshield wiper/ washer control (pg. 48) SEEK TRACK SCAN TUNE DISCS PUSH ON SIDE 1-2 Climate controls Passenger air bag (pg. 72) TAPE BASS TREB PREMIUM SOUND DOLBY B NR FADE COMP SHUF R.DEF Electronic sound system (pg. 36) Instrumentation (pg.

  • Page 8: Warning Lights And Chimes

    Instrumentation WARNING LIGHTS AND CHIMES Base instrument cluster FUEL FILL SERVICE ENGINE SOON FUEL BRAKE ZX2 coupe instrument cluster FUEL FILL FUEL – BRAKE SERVICE ENGINE SOON Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge (refer to Fuel gauge in this chapter for more information).
  • Page 9 Instrumentation Service engine soon Your vehicle is equipped with a SERVICE computer that monitors the engine’s ENGINE emission control system. This SOON system is commonly known as the On Board Diagnostics System (OBD II). The OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
  • Page 10 Instrumentation Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity. Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
  • Page 11 Instrumentation Anti-lock brake system (ABS) (If equipped) Momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with the parking brake released.
  • Page 12 Instrumentation Engine oil pressure Momentarily illuminates when the ignition is turned to the ON position and the engine is off. Illuminates when the oil pressure falls below the normal range. Stop the vehicle as soon as safely possible and switch off the engine immediately. Check the oil level and add oil if needed.

  • Page 13: Fuel Gauge

    ZX2 coupe instrument cluster gauges FUEL FILL FUEL – BRAKE SERVICE ENGINE SOON Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion.

  • Page 14: Trip Odometer

    Instrumentation Never remove the coolant reservoir cap while the engine is running or hot. This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. Speedometer Indicates the current vehicle speed.
  • Page 15 Instrumentation Tachometer (if equipped) Indicates the engine speed in revolutions per minute. THEFT Driving with your tachometer pointer in the red zone may damage RPMx1000 the engine.

  • Page 16: Controls And Features

    Controls and features PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. Coupe Rotate up to brighten. Rotate down to dim. Sedan Rotate left to brighten Rotate right to dim The dome lamp will not illuminate if the panel dimmer/dome lamp control is switched to OFF.
  • Page 17 Controls and features POWER SIDE VIEW MIRRORS (IF EQUIPPED) The ignition must be in ACC or ON position to adjust the power side view mirrors. To adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror. MIRRORS 2.

  • Page 18: Using Your Audio System

    Controls and features USING YOUR AUDIO SYSTEM AM/FM Stereo/Cassette SEEK TUNE Volume/power control Press the control to turn the audio system on or off. Turn control to raise or lower volume. SCAN DOLBY B NR PUSH ON SIDE 1-2 TAPE BASS TREB FADE...
  • Page 19 If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. If you wish to maintain your preset volume level, turn the audio system off with the power control before switching off the ignition.
  • Page 20 Controls and features Tune adjust in radio mode Press the to move to the next frequency down the band (whether or not a listenable station is located there). Hold to move through the frequencies quickly. Press the to move to the next frequency up the band (whether or not a listenable station is located there).
  • Page 21 Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape.
  • Page 22 Controls and features Speaker balance/fade adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Toggle between the + and — control to adjust the speaker sound. Speaker sound can be adjusted between the front and rear speakers.
  • Page 23 Fast forward The fast forward control works in tape mode. In the tape mode, tape direction will automatically reverse when the end of the tape is reached. Tape side select Press this control to play the alternate side of a tape. Eject function Press the control to stop and eject a tape.

  • Page 24: Setting The Clock

    Controls and features Setting the clock To set the hour, press the hour (h) control and press : (+) to increase hour and (−) to decrease hour To set the minute, press the minute (m) control and press: (+) to increase minutes and (−) to decrease minutes.
  • Page 25 Volume/power control Press the control to turn the audio system on or off. Turn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
  • Page 26 Controls and features AM/FM select in CD mode Press this control to stop CD play and begin radio play. You can switch from CD play to tape play by simply inserting a tape into the cassette deck. Tune adjust The tune control works in radio or CD mode (if equipped).
  • Page 27 Seek function The seek function control works in radio, tape or CD mode (if equipped). Seek function in radio mode Press to find the next listenable station down the frequency band. Press to find the next listenable station up the frequency band. Seek function in tape mode Press to listen to the previous selection on the tape.
  • Page 28 Controls and features Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape.
  • Page 29 Bass/treble adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. The treble adjust control allows you to increase or decrease the audio system’s treble output. Speaker balance/fade adjust Speaker sound distribution can be adjusted between the right and left speakers.
  • Page 30 Controls and features Rewind The rewind control works in tape and CD modes (if equipped). In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. In CD mode, pressing the REW control for less than three seconds results in slow rewind.
  • Page 31 Dolby noise reduction Dolby noise reduction operates only in tape mode. Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby noise reduction. Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation.
  • Page 32 Controls and features Setting the clock To set the hour, press the hour (h) control and press : (+) to increase the hour and (−) to decrease the hour To set the minute, press the minute (m) control and press: (+) to increase the minute and (−) to decrease the minute CD changer (if equipped)
  • Page 33 Make sure only one disc is inserted in each slot. Each disc must be inserted with the label surface upward. You may insert up to six CDs. The magazine does not need to be full for the changer to operate. Radio power must be turned on to play the CDs in the changer.
  • Page 34 Controls and features Troubleshooting the CD changer (if equipped) The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case. If sound skips: You may be traveling on a rough road, playing badly scratched discs or the disc may be dirty.
  • Page 35 Do not expose tapes to direct sunlight, high humidity, extreme heat or extreme cold. Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing. Tighten very loose tapes by inserting a finger or pencil into the hole and turning the hub.
  • Page 36 Controls and features Audio system warranties and service Refer to the “Warranty Guide” for audio system warranty information. If service is necessary, see your dealer or a qualified technician. CLIMATE CONTROL SYSTEM Heater only system (if equipped) Fan speed control Controls the volume of air circulated in the vehicle.
  • Page 37 (Floor and defrost)-Distributes outside air through the floor ducts and the windshield defroster ducts. -Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. Operating tips In humid weather, select on your windshield.
  • Page 38 Controls and features Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor will operate in all modes except .
  • Page 39 Controls and features OFF-Outside air is shut out and the fan will not operate. For short periods of time only, use this mode to prevent undesirable odors from entering the vehicle. (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode.
  • Page 40 Controls and features Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield). If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
  • Page 41 POSITIONS OF THE IGNITION 1. LOCK, locks the steering wheel, gearshift lever (automatic transaxle only) and allows key removal. On vehicles with a manual transaxle push the key in while turning to lock. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running.
  • Page 42 Controls and features High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. Foglamp control (if equipped) Rotate forward to activate.
  • Page 43 TURN SIGNAL CONTROL Push down to activate the left turn signal. Push up to activate the right turn signal. SPEED CONTROL (IF EQUIPPED) To turn speed control on Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph).
  • Page 44 Controls and features To turn speed control off Press OFF or Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
  • Page 45 To set a higher set speed Press and hold SET/SET ACC/ SET ACCEL. Release the control when the desired vehicle speed is reached or Press and release SET/SET ACC/ SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or Accelerate with your accelerator pedal.
  • Page 46 Controls and features To disengage speed control Depress the brake pedal or Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
  • Page 47 To return to a previously set speed Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). TILT STEERING (IF EQUIPPED) Pull the tilt steering control down to move the steering wheel up or down.
  • Page 48 Controls and features WINDSHIELD WIPER AND WASHER For intermittent wiping, move the control down one position and rotate the wiper switch to the desired position. For low speed wiping, move the control down two positions. For high speed wiping, move the control down three positions.
  • Page 49 MOON ROOF (IF EQUIPPED) Press and hold OPEN to raise the moon roof to the vent position. Press OPEN again to fully open the moon roof. Press the opposite end of the toggle control to close the moon roof from either position. Sliding shade The moon roof has a sliding shade that you can open or close when the moon roof is closed.
  • Page 50 Controls and features If equipped with a moon roof, the map lamps are located on the moon roof control panel. Press the control OPEN next to the map lamp to illuminate the lamp. POWER DOOR LOCKS (IF EQUIPPED) Press U to unlock all doors and L to lock all doors.
  • Page 51 POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. Press the top portion of the rocker switch to close. Press the bottom portion of the rocker switch to open. Express down To make the driver window open fully without holding the window control, press the driver window control completely down and release...
  • Page 52 Controls and features POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
  • Page 53 Keep vehicle doors and luggage compartment locked and keep keys out of a child’s reach. Unsupervised children could lock themselves in an open trunk and risk injury. Children should be taught not to play in vehicles. On hot days, the temperature in the trunk or vehicle interior can rise very quickly.
  • Page 54 Controls and features Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. With the all-door remote entry system, press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors.
  • Page 55 Opening the trunk Press the control once to open the trunk. Ensure that the trunk is closed and latched before driving your vehicle. Failure to latch the trunk completely may cause objects to fall out of the trunk or block the rear view.
  • Page 56 Controls and features To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation.
  • Page 57 To program the transmitters yourself: Insert a key in the ignition and turn from 2 (ACC) to 3 (ON) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 3 (ON) position. The doors will lock/unlock to confirm that programming mode has been entered.
  • Page 58 Controls and features Arming the anti-theft system Turn the ignition to OFF and press the lock control on the remote entry transmitter. Identifying an armed system While the system is arming, the THEFT light in the instrument cluster will illuminate for 30 seconds. After 30 seconds, THEFT will flash, indicating the system is armed.
  • Page 59 Controls and features A triggered system may also be disarmed by inserting the key and turning the ignition to ON/ACC or by pressing the panic control. Pressing the trunk control will prevent the alarm from sounding until the trunk is closed again. Using the ignition key to unlock doors/trunk will not disarm the anti-theft system.

  • Page 60: Seating And Safety Restraints

    Seating and safety restraints SEATING Adjustable head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
  • Page 61 Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. Lift handle to move seat forward or backward.
  • Page 62 Seating and safety restraints Driver seat memory recliner (if equipped) Pull control to adjust seatback. To retain selected seatback position, release seatback by moving memory recliner control forward to release seatback. Push seatback rearward until the seatback latches. This will be the first position selected.
  • Page 63 Folding rear seats (if equipped) Folding down the rear seats To fold the seatback down: Press the latch control downward or pull up on strap and Pull the seatback forward and down. Returning the seat to the upright position Check to see that the seat and seatback is latched securely in position.
  • Page 64 Seating and safety restraints To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
  • Page 65 When to use the automatic locking mode Anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible.
  • Page 66 Seating and safety restraints How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Front safety belt height adjustment (if equipped) Your vehicle has safety belt height adjustments for the driver and front passenger.
  • Page 67 Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
  • Page 68 Seating and safety restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding...
  • Page 69 3 of 4 fatal crashes occur within 25 miles of home. Ford designs its safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible;...
  • Page 70 Seating and safety restraints One time disable Anytime the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only. Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.
  • Page 71 (if equipped), shoulder belt guide on seatback (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced.
  • Page 72 This information will assist Ford in the servicing of your vehicle and may help Ford better understand real world collisions and further improve the safety of future vehicles.
  • Page 73 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may effect the performance of the air bag sensors increasing the risk of injury.
  • Page 74 Seating and safety restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
  • Page 75 The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag.
  • Page 76 Seating and safety restraints The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
  • Page 77 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
  • Page 78 Seating and safety restraints back on the seat cushion when the lower legs hang over the edge of the seat cushion. You may wish to discuss the special needs of your child with your pediatrician. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child.
  • Page 79 (passenger side front and outboard rear seating positions) (if equipped). Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps.
  • Page 80 Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
  • Page 81 Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
  • Page 82 Seating and safety restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap.
  • Page 83 For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback. 3. Locate the correct anchor for the selected seating position. 4.

  • Page 84: Starting

    Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
  • Page 85 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. If starting a vehicle with an automatic transaxle: Make sure the gearshift is in P (Park). If starting a vehicle with a manual transaxle: Push the clutch pedal to the floor.
  • Page 86 Starting 4. Turn the key to 3 (ON) without turning the key to 4 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns freely. This condition may occur when: front wheels are turned front wheel is against the curb...
  • Page 87 STARTING THE ENGINE Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1. Turn the key to 4 (START) without pressing the accelerator pedal and release as soon as the engine starts.
  • Page 88 Starting Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes.

  • Page 89: Driving

    Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
  • Page 90 Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the...
  • Page 91 The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency.
  • Page 92 Driving high crosswinds wheels out of alignment loose or worn components in steering linkage AUTOMATIC TRANSAXLE OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) unless the brake pedal is depressed.
  • Page 93 3. Push and hold the thumb button. 4. Move the gearshift lever. If it is necessary to use the above procedure to move the gearshift lever, it is possible that a fuse has blown and the vehicle’s brakelamps may not be operating properly. Refer to Fuses and relays in the Roadside emergencies chapter.
  • Page 94 Driving Understanding gearshift positions Hold the brake pedal down while you move the gearshift lever from P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) Always come to a complete stop before shifting into P (Park).
  • Page 95 N (Neutral) With the gearshift lever in the N (Neutral) position, the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. (Overdrive) The overdrive position is the normal driving position for an automatic overdrive transaxle.
  • Page 96 Driving D (Drive) D (Drive) eliminates the needless shifting between third and fourth gears that your vehicle may do when driving in hilly terrain. It also gives more engine braking than overdrive to slow your vehicle on downgrades. L (Low) Use L (Low) when added engine braking is desired or when descending steep hills.
  • Page 97 MANUAL TRANSAXLE OPERATION (IF EQUIPPED) Using the clutch Vehicles equipped with a manual transaxle have a starter interrupt interlock that prevents cranking of the engine unless the clutch pedal is depressed. When starting a vehicle with a manual transaxle, you must: 1.
  • Page 98 Driving Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Set the parking brake. 3. Shift into 1 (First).
  • Page 99 4. Turn engine off and remove the key. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts when accelerating (recommended for best fuel economy) Upshifts when cruising (recommended for best fuel economy) Reverse...
  • Page 100 Driving Put the gearshift lever into the neutral position and wait at least three seconds before shifting into R (Reverse). You can shift into R (Reverse) only by moving the gearshift lever from left of 3 (Third) and 4 (Fourth) gears before you shift into R (Reverse). This is a special lockout feature which prevents you from shifting into R (Reverse) when you downshift from 5 (Fifth).
  • Page 101 Maximum Trailer Weight Rating: Maximum weight of a trailer the vehicle is permitted to tow. The maximum trailer weight rating is determined by subtracting the vehicle curb weight for each engine/transmission combination, any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle.
  • Page 102 Driving TRAILER TOWING Your vehicle is capable of towing a trailer up to 454 kg (1 000 lbs.) gross trailer weight with a maximum tongue load of 45 kg (100 lbs.). Do not tow a trailer until your vehicle has been driven at least 800 km (500 miles).
  • Page 103 Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. The braking system of the tow vehicle is rated for operation at the GVWR not GCWR.
  • Page 104 Driving After you have traveled 80 km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts. When stopped in traffic for long periods of time in hot weather, place the gearshift in P (Park) and increase idle speed. This aids engine cooling and air conditioner efficiency.

  • Page 105: Roadside Emergencies

    GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: 24–hours, seven days a week for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.) of three years or 60,000 km (36,000 miles),...
  • Page 106 Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance Club brochure or by calling 1–877–294–CLUB (1–877–894–2582).
  • Page 107 Right side of the trunk behind the trunk liner. Driver’s foot well, behind the kick panel. The fuel pump shut-off switch, depending on application, is located on the right side of the trunk behind the trunk liner or in the driver’s foot well, behind the kick panel.
  • Page 108 Roadside emergencies Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button.
  • Page 109 Standard fuse amperage rating and color Fuse Mini Rating Fuses Grey Violet Pink 7.5A Brown Blue Yellow Natural Green — — — — — Roadside emergencies COLOR Standard Maxi Fuses Fuses Grey — Violet — Pink — — Brown — —...
  • Page 110 Roadside emergencies Passenger compartment fuse panel Coupe The fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating HAZARD ROOM ENGINE RADIO DOOR LOCK HORN AIR COND METER P. Window (C.B.) (DRL) (DOOR LK) STOP HAZARD HORN TAIL ROOM (AIR COND) (SUN ROOF) ENGINE METER...
  • Page 111 Fuse/Relay Fuse Amp Location Rating WIPER STOP TAIL SUN ROOF P. WINDOW 30A CB CIGAR AIR BAG AUDIO FUEL INJ. BLOWER 30A CB Sedan Roadside emergencies Passenger Compartment Fuse Panel Description Wiper/Washer, Blower Motor Relay Stop Lamps, Brake Pressure Switch Exterior Lamps, Instrument Illumination Power Moonroof Speed Control...
  • Page 112 Roadside emergencies The fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating R.WIPER HAZARD ROOM ENGINE MIRROR DOOR LOCK HORN AIR COND METER WIPER STOP TAIL SUN ROOF CIGAR AIR BAG AUDIO FUEL INJECTOR P. WINDOW 30A CB BLOWER 30A CB Passenger Compartment Fuse Panel Description...
  • Page 113 Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
  • Page 114 Roadside emergencies Fuse/Relay Fuse Amp Location Rating 40A* 60A* COOLING 40A* OBD-II 10A* FUEL 20A** PUMP HEAD RH 10A** HEAD LH 10A** * Fuse Link Cartridge **Fuse Sedan HEADLAMP Power Distribution Box Description Hazard, Stop, Door Lock, Tail, Room and Horn Fuses of the I/P Fuse Panel ABS Main Relay Constant Control Relay Module (Cooling...
  • Page 115 The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating FUEL INJ. 30A* DEFOG 30A* MAIN 100A* 40A* 60A* COOLING 40A* OBD-II 10A** FUEL 20A** PUMP HEAD RH 10A** HEAD LH 10A** * Fuse Link Cartridge ** Fuse Relays Relays are located in the power distribution box and should be replaced by qualified technicians.
  • Page 116 Roadside emergencies When driving with the temporary spare tire do not: exceed 80 km/h (50 mph) under any circumstances load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label tow a trailer use tire chains drive through an automatic car wash, because of the vehicle’s reduced ground clearance try to repair the temporary spare tire or remove it from its wheel use the wheel for any other type of vehicle...
  • Page 117 2. Place gearshift lever in P (Park) (automatic transaxle) or R (Reverse) (manual transaxle), turn engine OFF, and block the diagonally opposite wheel. Automatic Manual 3. Remove the jack, jack handle and spare tire. Roadside emergencies...
  • Page 118 Roadside emergencies 4. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 5. Put the jack in the jack notch next to the door of the tire you are changing.
  • Page 119 JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted.
  • Page 120 Roadside emergencies Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
  • Page 121 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
  • Page 122 Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
  • Page 123 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
  • Page 124 It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.

  • Page 125: Maintenance And Care

    SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
  • Page 126 Maintenance and care 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Manual transaxle: 1.
  • Page 127 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on Automatic transaxle: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park).
  • Page 128 Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Manual transaxle: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2.
  • Page 129 Maintenance and care OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
  • Page 130 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L SOHC I4 engine 1. Engine oil dipstick 2. Brake fluid reservoir 3. Transmission fluid dipstick (automatic transaxle) 4. Battery 5. Air filter assembly 6. Engine oil filler cap 7. Power steering fluid reservoir 8.
  • Page 131 Maintenance and care 2.0L DOHC Zetec engine 1. Transmission fluid dipstick (automatic transaxle) 2. Battery 3. Air filter assembly 4. Engine oil filler cap 5. Engine oil dipstick 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9.
  • Page 132 Maintenance and care ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan.
  • Page 133 2.0L DOHC Zetec engine 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range.
  • Page 134 Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced.
  • Page 135 MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes.
  • Page 136 Maintenance and care CLUTCH FLUID (IF EQUIPPED) Check the clutch fluid level. Refer to the Scheduled Maintenance Guide for the service interval schedules. The clutch master cylinder and brake master cylinder are part of the same system; both are refillable through the brake master cylinder with brake fluid.
  • Page 137 If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way. Only use a washer fluid that meets Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter.
  • Page 138 Maintenance and care protection against rust and other forms of corrosion. an accurate temperature readout from the engine coolant gauge. The engine coolant must be maintained at the correct fluid level and concentration to work properly. If the engine coolant fluid level and concentration is not maintained correctly, damage to the engine and cooling system may result.
  • Page 139 Adding engine coolant Use only Ford Premium Engine Coolant E2FZ-19549-AA (in Canada, Motorcraft CXC-10) or a premium engine coolant that meets Ford specification ESE-M97B44-A. DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA (orange in color).
  • Page 140 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44-A.
  • Page 141 Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter.
  • Page 142 Maintenance and care Vehicles driven year-round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the Scheduled Maintenance Guide for the service interval schedules.
  • Page 143 Maintenance and care 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir. TRANSMISSION FLUID Checking automatic transmission fluid Refer to your Scheduled Maintenance Guide for scheduled intervals for fluid checks and changes.
  • Page 144 Maintenance and care Correct fluid level The transmission fluid should be checked at normal operating temperatures 66°C-77°C (150°F-170°F) on a level surface. The normal operating temperature can be reached after approximately 30 km (20 miles) of driving. The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]).
  • Page 145 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
  • Page 146 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules.
  • Page 147 When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
  • Page 148 Maintenance and care Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. AIR FILTER MAINTENANCE Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the air filter element.
  • Page 149 Maintenance and care WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades. Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild...
  • Page 150 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
  • Page 151 The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure Use an accurate tire pressure gauge.
  • Page 152 Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over.
  • Page 153 recommended that steel wheels are used of the same size and specifications as those originally installed. Follow these guidelines when using snow tires and chains: Do not use tire chains on aluminum wheels. Chains may chip the wheels. Use only SAE Class S chains. Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines.
  • Page 154 Maintenance and care If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision, which may result in possible personal injury.
  • Page 155 Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If fuel is splashed on the skin, promptly wash skin thoroughly with soap and water.
  • Page 156 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
  • Page 157 World-wide Fuel Charter. Cleaner air Ford approves the use of reformulated “cleaner-burning” gasolines to improve air quality. These gasolines may contain oxygenates up to 10% ethanol or 15% MTBE. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components.
  • Page 158 Maintenance and care Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician. Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used.
  • Page 159 Use a known quality gasoline, preferably a national brand. Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent.
  • Page 160 Maintenance and care Anticipate stopping; slowing down may eliminate the need to stop. Sudden or hard accelerations may reduce fuel economy. Slow down gradually. Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15% less fuel than traveling at 105 km/h [65 mph]). Revving the engine before turning it off may reduce fuel economy.
  • Page 161 Guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
  • Page 162 Maintenance and care Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the “Service Engine Soon” light, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly.
  • Page 163 engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. BULBS Replacing exterior bulbs It is a good idea to check the operation of the following lights frequently: Headlamps Turn signals Foglamps (if equipped)
  • Page 164 Maintenance and care 5. Remove the bulb retaining ring by rotating it counterclockwise. 6. Without turning, remove the old bulb from the lamp assembly by pulling it straight back out of the lamp assembly and replace. Handle a halogen headlamp bulb carefully and keep out of children’s reach.
  • Page 165 Maintenance and care Replacing foglamp bulbs 1. Remove the bulb socket from the foglamp by turning counterclockwise. 2. Disconnect the electrical connector from the foglamp bulb. 3. Connect the electrical connector to the new foglamp bulb. 4. Install the bulb socket in the foglamp turning clockwise.
  • Page 166 Maintenance and care Tail lamp/turn signal/backup lamp bulbs The tail/turn signal lamp and backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb. 1.
  • Page 167 Maintenance and care License plate lamps To change the license plate bulbs: 1. Remove two screws and the license plate lamp assembly from the rear bumper. 2. Carefully pull the bulb out from the lamp assembly and push in the new bulb.
  • Page 168 Maintenance and care Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility.
  • Page 169 Horizontal aim adjustment 1. Park the vehicle on a level surface. 2. With the hood open, locate the horizontal indicator and the adjusting screw. They are located below the viewing window at the rear of the headlamp assembly. 3. The “L” and “R” under the viewing window on the top of the headlamp refer to the directional change (left or right) of the horizontal aim.
  • Page 170 Repeat the above process to the other headlamp, if necessary. CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water.
  • Page 171 Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), Lacquer Touch-up Paint (#ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring. Observe the application instructions on the products.
  • Page 172 Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners.
  • Page 173 Never apply anything to the drive belt (including belt dressing). Cover the highlighted areas to prevent water damage when cleaning the engine. Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth.
  • Page 174 For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label.

  • Page 175: Capacities And Specifications

    ** If a spark plug is removed for inspection, it must be reinstalled in the same cylinder.If a spark plug needs to be replaced, use only spark plugs with the same service part number suffix letter as shown on the engine decal. REFILL CAPACITIES Ford Part Fluid Name Brake fluid High...
  • Page 176 Ultra-Clear washer fluid Windshield Washer Concentrate Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. LUBRICANT SPECIFICATIONS Ford Part...
  • Page 177 Windshield Ultra-clear washer fluid Windshield Washer Concentrate DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA, meeting Ford specification WSS-M97B44-D (orange in color) Refer to Adding engine coolant, in the Maintenance and Care chapter. ENGINE DATA Engine Cubic inches Required fuel...
  • Page 178 Capacities and specifications VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear Coupe and Sedan models Coupe mm (in) 4 451.0 (175.2) 1 712.0 (67.4) 1 328.4 (52.3) 2 499.0 (98.4) 1 435.1 (56.5) 1 435.1 (56.5)
  • Page 179 Coupe model Coupe model Capacities and specifications...

  • Page 180: Certification Label

    Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side. MFD. BY FORD MOTOR CO. IN U.S.A. DATE: XXXXX GVWR:XXXXX LB/ XXXXX KG FGAWR: XXXXXX/XXXXXXX RGAWR: XXXXXXX/XXXXXXX...
  • Page 181 Capacities and specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side XXXXXXXXXXXXXXXXX instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block and transmission.

  • Page 182: Customer Assistance

    5,000 participating Ford or Lincoln/Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Please contact your dealer for further information. Since this information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options.
  • Page 183 Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you.
  • Page 184 Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Assistance Center: Your telephone number (home and business)
  • Page 185 Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
  • Page 186 Ford Motor Company...
  • Page 187 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
  • Page 188 UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
  • Page 189 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY...
  • Page 190 Customer assistance Ford Deluxe Leather and Vinyl Cleaner (not available in Canada) Motorcraft Vinyl Cleaner (Canada only) Ford Extra Strength Tar and Road Oil Remover* (not available in Canada) Ford Extra Strength Upholstery Cleaner (Canada only) Ford Extra Strength Upholstery Cleaner (not available in Canada)
  • Page 191 Customer assistance Comfort and convenience Air conditioner Cargo nets Cargo organizers Engine block heaters Travel equipment Auto headlamps with daytime running lights (DRL) Console armrest Daytime running lights (DRL) Electrochromic inside mirror with compass Electrochromic inside mirror with compass and temperature display Heavy-duty battery Removable luggage rack Removable luggage rack adapters...
  • Page 192 (Citizens band [CB] transceivers, garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle’s operation.) Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment. ORDERING ADDITIONAL OWNER’S LITERATURE...

  • Page 193: Reporting Safety Defects

    However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.

  • Page 194: Index

    Index Air bag supplemental restraint system ...72 and child safety seats ...74 description ...72 disposal ...76 driver air bag ...74 indicator light ...10,76 operation ...74 passenger air bag ...74 Air cleaner filter ...148,175 Air conditioning ...36 Antifreeze (see Engine coolant) ...137 Anti-lock brake system (see Brakes) ...89,90 Anti-theft system ...57,58...
  • Page 195 ...137 refill capacities ...141,175 specifications ...176,177 Cruise control (see Speed control) ...43 Customer Assistance ...105 Ford accessories for your vehicle ...189 Ford Extended Service Plan ...182 Getting assistance outside the U.S. and Canada ...188 Getting roadside assistance ...105 Getting the service you need ...182...
  • Page 196 Index Gas mileage (see Fuel economy) ...158 Gauges ...12,13 engine coolant temperature gauge ...13 fuel gauge ...13 odometer ...14 speedometer ...14 tachometer ...15 trip odometer ...14 GAWR (Gross Axle Weight Rating) ...100 definition ...100 driving with a heavy load ...100 location ...100 GVWR (Gross Vehicle Weight Rating) ...100...
  • Page 197 Manual transaxle ...97 fluid capacities ...175 lubricant specifications ...177 reverse ...99 Mirrors cleaning ...172 side view mirrors (power) ...17 Moon roof ...49 Motorcraft parts ...158,175 Octane rating ...156 Odometer ...14 Oil (see Engine oil) ...132 Panic alarm feature, remote entry system ...55 Parking brake ...90 Parts (see Motorcraft parts) ...175 Power distribution box...
  • Page 198 Index fluid, checking and adding (manual) ...145 lubricant specifications ...176 Trip odometer ...14 Trunk ...52 remote release ...17,55 Turn signal ...11,43 Vehicle dimensions ...178 Vehicle Identification Number (VIN) ...181 Vehicle loading ...100 Ventilating your vehicle ...88 Warning chimes ...12 Warning lights (see Lights) ...8 Washer fluid ...136 Water, Driving through ...104 Windows...

  • Page 200: Filling Station Information

    Power steering fluid capacity Automatic transaxle capacity Manual transaxle capacity Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter.

This manual is also suitable for:

1999 escort

Table of Contents