Page 1 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Copyright 1998 Ford Motor Company...
Page 2: Introduction
INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.
Page 3: Instrumentation
Instrumentation...
Page 4 Instrumentation Foglamp control * (pg. 44) Headlamp control (pg. 42) MIRROR Power side view mirrors* (pg. 14) Instrument panel dimmer switch (pg. 14) *if equipped Instrument cluster FUEL FILL FUEL Speed control* (pg. 44) (pg. 6) THEFT RPMx1000 0 0 0 1 1 3 Driver side air bag (pg.
Page 5: Climate Control System
Windshield wiper/ washer control (pg. 49) SEEK TRACK SCAN TUNE DISCS PUSH ON SIDE 1-2 Climate control system Passenger side air bag (pg. 71) TAPE BASS TREB PREMIUM SOUND DOLBY B NR FADE COMP SHUF R.DEF Electronic sound system (pg. 37) Instrumentation (pg.
Page 6: Warning Lights And Chimes
Instrumentation WARNING LIGHTS AND CHIMES Base instrument cluster FUEL FILL SERVICE ENGINE SOON FUEL BRAKE Sport instrument cluster FUEL FILL SERVICE ENGINE SOON FUEL BRAKE ZX2 coupe instrument cluster FUEL FILL FUEL – BRAKE SERVICE ENGINE SOON 60 70 0 0 0 0 0 0 0 0 km/h 60 70...
Page 7 Instrumentation Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge. The light comes on when FUEL there is approximately 1/16th of a tank indicated on the fuel gauge (refer to Fuel gauge in this chapter for more information). The ignition must be in the ON position for this lamp to illuminate.
Page 8 Instrumentation temporary malfunctions present, the Service Engine Soon light should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required. If the Service Engine Soon light remains on, have your vehicle serviced at the first available opportunity.
Page 9 Instrumentation Shift indicator light (if equipped) To maximize fuel economy, the shift indicator light illuminates when the manual transmission should be shifted to the next highest gear. Anti-lock brake system (ABS) (If equipped) Momentarily illuminates when the ignition is turned on and the engine is off.
Page 10 Instrumentation Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service. Engine oil pressure Momentarily illuminates when the ignition is turned to the ON position and the engine is off.
Page 11 GAUGES Base instrument cluster gauges FUEL FILL SERVICE ENGINE FUEL SOON BRAKE Sport instrument cluster gauges FUEL FILL SERVICE ENGINE SOON FUEL BRAKE ZX2 coupe instrument cluster gauges FUEL FILL FUEL – BRAKE SERVICE ENGINE SOON 60 70 0 0 0 0 0 0 0 0 km/h 60 70...
Page 12 Instrumentation Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
Page 13 Speedometer Indicates the current vehicle speed. Odometer Registers the total kilometers (miles) of the vehicle. Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. Tachometer (if equipped) Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer in the red zone may damage the engine.
Page 14: Controls And Features
Controls and features PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. Coupe Rotate up to brighten. Rotate down to dim. Sedan/Wagon Rotate left to brighten. Rotate right to dim. POWER SIDE VIEW MIRRORS (IF EQUIPPED) The ignition must be in ACC or ON position to adjust the power side view mirrors.
Page 15 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. TRUNK REMOTE CONTROL Press the remote trunk release control on the instrument panel to open the trunk. USING YOUR AUDIO SYSTEM AM/FM stereo SEEK...
Page 16 Controls and features Volume/power control Press the control to turn the audio system on or off. Turn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Page 17 Tune adjust The tune control works in radio mode. Tune adjust in radio mode Press the to move to the next frequency down the band (whether or not a listenable station is located there). Hold the to move through the frequencies quickly.
Page 18 Controls and features Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2).
Page 19 Speaker balance/fade adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Toggle between the + and — control to adjust the speaker sound. Speaker sound can be adjusted between the front and rear speakers.
Page 20 Controls and features AM/FM Stereo/Cassette SEEK SCAN TUNE PUSH ON Volume/power control Press the control to turn the audio system on or off. Turn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 21 volume level, turn the audio system off with the power control before switching off the ignition. AM/FM select The AM/FM select control works in radio modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
Page 22 Controls and features Seek function The seek function control works in radio or tape mode. Seek function in radio mode Press to find the next listenable station down the frequency band. Press to find the next listenable station up the frequency band. Seek function in tape mode Press to listen to the previous selection on the tape.
Page 23 Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
Page 24 Controls and features Inserting a tape Push only slightly when inserting a cassette tape (with the open edge to the right). A cassette deck loading mechanism pulls the tape in the rest of the way. You can switch from radio to tape play by inserting a tape into the cassette deck.
Page 25 Eject function Press the control to stop and eject a tape. Dolby noise reduction Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation operates only in tape mode. Dolby reduces the amount of hiss and static during tape playback.
Page 26 Controls and features Premium AM/FM Stereo/Cassette/ Premium Sound (Radio Controlled CD Changer Compatible) SEEK TRACK SCAN TUNE DISCS PUSH ON Volume/power control Press the control to turn the audio system on or off. Turn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 27 ignition switch is turned back on. If you wish to maintain your preset volume level, turn the audio system off with the power control before switching off the ignition. AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped).
Page 28 Controls and features Tune adjust in radio mode Press the to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. Press the right side of the control to move to the next frequency up the band (whether or not a listenable station is located there).
Page 29 Seek function in tape mode Press to listen to the previous selection on the tape. Press to listen to the next selection on the tape. Seek function in CD mode (if equipped) Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning.
Page 30 Controls and features Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
Page 31 Inserting a tape Push only slightly when inserting a cassette tape (with the open edge to the right). A cassette deck loading mechanism pulls the tape in the rest of the way. You can switch from CD (if equipped) to tape play by inserting a tape into the cassette deck.
Page 32 Controls and features Tape side select Press this control to play the alternate side of a tape. SIDE 1-2 Eject function Press the control to stop and eject a tape. DOLBY B NR Dolby noise reduction Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation operates only in tape mode.
Page 33 Shuffle feature The shuffle feature operates in CD mode (if equipped) and plays all tracks on the current disc in random order. If equipped with the CD changer, the shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature.
Page 34 Controls and features CD changer (if equipped) The CD changer is located in the trunk of your vehicle. Slide the door to access the CD changer magazine. Press to eject the magazine. Make sure only one disc is inserted in each slot. Each disc must be inserted with the label surface upward.
Page 35 The magazine does not need to be full for the changer to operate. Radio power must be turned on to play the CDs in the changer. The magazine may be stored in the glove box when not being used. The CD magazine may be inserted or ejected with the radio power off. Troubleshooting the CD changer (if equipped) The laser beam used in the compact disc player is harmful to the eyes.
Page 36 Controls and features CD and CD changer care Handle discs by their edges only. Never touch the playing surface. Do not expose discs to direct sunlight or heat sources for extended periods of time. Do not insert more than one disc into each slot of the CD changer magazine.
Page 37 Terrain. Hills, mountains and tall buildings between your vehicle’s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns your reception to normal.
Page 38 Controls and features Mode selector control Controls the direction of the airflow to the inside of the vehicle. (Panel)-Distributes outside air through the instrument panel registers. OFF-Outside air is shut out and the fan will not operate. (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts.
Page 39 airflow and reduce your ability to see through your windshield. Also, avoid placing small objects on top of your instrument panel. These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system. Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop.
Page 40 Controls and features the air conditioner drain while the system is working and even after you have stopped the vehicle. Under normal conditions, your vehicle’s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked.
Page 41 instrument panel registers. If the temperature is about 10°C (50°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. -Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the temperature is about 10°C (50°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging.
Page 42 Controls and features REAR WINDOW DEFROSTER Clears the rear window of thin ice and fog. To operate: 1. Turn the ignition to the ON position. 2. Press and release the control once to turn on. The light will be lit while the rear window defroster is R.DEF 3.
Page 43 Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: the ignition must be in the ON position and the headlamp control is in the OFF or Parking lamps position. Always remember to turn on your headlamps at dusk or during inclement weather.
Page 44 Controls and features FOGLAMP CONTROL (IF EQUIPPED) Rotate forward to activate. SPEED CONTROL (IF EQUIPPED) To turn speed control on Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
Page 45 To turn speed control off Press OFF or Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
Page 46 Controls and features To set a higher set speed Press and hold SET/SET ACC/SET ACCEL. Release the control when the desired vehicle speed is reached or Press and release SET/SET ACC/SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or Accelerate with your accelerator pedal.
Page 47 To disengage speed control Depress the brake pedal or Depress the clutch pedal (if equipped) Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. Controls and features...
Page 48 Controls and features To return to a previously set speed Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). TILT STEERING (IF EQUIPPED) Pull the tilt steering control down to move the steering wheel up or down.
Page 49 Controls and features WINDSHIELD WIPER AND WASHER For intermittent wiping, move the control down one position and rotate the wiper switch to the desired position. For low speed wiping, move the control down two positions. For high speed wiping, move the control down three positions.
Page 50 Controls and features Rear window wiper/washer controls (if equipped) For rear wiper operation, rotate the rear wiper and washer control to the desired position. To turn rear wipers on, rotate the rear wiper/washer control upward to the ON position. To turn rear wipers off, rotate the rear wiper/washer control downward to the OFF position.
Page 51 Controls and features INTERIOR LAMPS Dome lamp and map lamps (if equipped) The dome lamp is located overhead between the driver and passenger seats. The dome lamp will stay on if the control is moved to the ON position. When the control is moved to the DOOR position, the lamp will only come on if a door is opened.
Page 52 Controls and features POWER DOOR LOCKS (IF EQUIPPED) Press U to unlock all doors and L to lock all doors. CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked.
Page 53 POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. Press the top portion of the rocker switch to close. Press the bottom portion of the rocker switch to open. Express down To make the driver window open fully without holding the window control, press the driver window control completely down and release...
Page 54 Controls and features POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
Page 55 REMOTE ENTRY SYSTEM Your vehicle may have an all-door remote entry system or a driver’s door only remote entry system. The all-door remote entry system allows you to: lock or unlock all vehicle doors without a key. arm and disarm the anti-theft system. (For more information on the anti-theft system, refer to Anti-theft system in this chapter.) open the trunk or unlock liftgate (wagons).
Page 56 Controls and features Locking the doors Press this control to lock all doors (and liftgate on wagons). On vehicles equipped with the driver’s door only remote entry system, only the driver’s (and liftgate on wagons) door will lock. To confirm doors are closed and locked, press the lock control a second time within five seconds.
Page 57 Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada.
Page 58 Controls and features Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement. Replacing lost transmitters Take all your vehicle’s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed), perform the following...
Page 59 Arming the anti-theft system Turn the ignition to OFF and press the lock control on the remote entry transmitter. Identifying an armed system While the system is arming, the THEFT light in the instrument cluster will illuminate for 30 seconds. After 30 seconds, THEFT will flash, indicating the system is armed.
Page 60 Controls and features A triggered system may also be disarmed by inserting the key and turning the ignition to ON/ACC or by pressing the panic control. On station wagons models, pressing the trunk control only will unlock and disarm the anti-theft system. On non-station wagon models, pressing the trunk control will prevent the alarm from sounding...
Page 61: Seating And Safety Restraints
Seating and safety restraints SEATING Adjustable head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 62 Seating and safety restraints Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Page 63 Seating and safety restraints Driver seat memory recliner (if equipped) Pull control to adjust seatback. To retain selected seatback position, release seatback by moving memory recliner control forward to release seatback. Push seatback rearward until the seatback latches. This will be the first position selected.
Page 64 Seating and safety restraints Folding rear seats (if equipped) Folding down the rear seats To fold the seatback down: Press the latch control downward or pull up on strap and Pull the seatback forward and down. Returning the seat to the upright position Check to see that the seat and seatback is latched securely in position.
Page 65 SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving.
Page 66 Seating and safety restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Page 67 How to use the automatic locking mode Buckle the combination lap and shoulder belt. Grasp the shoulder portion and pull downward until the entire belt is extracted. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Page 68 Seating and safety restraints Front safety belt height adjustment (if equipped) Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height control down.
Page 69 Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
Page 70 (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced.
Page 71 AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag...
Page 72 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer.
Page 73 Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Page 74 Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 75 The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Page 76 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
Page 77 (passenger side front and outboard rear seating positions) (if equipped). Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps.
Page 78 Seating and safety restraints Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 79 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
Page 80 Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. All vehicles built for sale in Canada include a tether anchor hardware kit.
Page 81 Tether anchorage hardware kits including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. All vehicles built for sale in Canada include a tether anchor hardware kit. Be sure to follow the child safety seat manufacturer’s instructions.
Page 82 Seating and safety restraints Sedan Wagon...
Page 83: Starting
PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 84 Starting 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. If starting a vehicle with an automatic transaxle: Make sure the gearshift is in P (Park). If starting a vehicle with a manual transaxle: Push the clutch pedal to the floor.
Page 85 4. Turn the key to 3 (ON) without turning the key to 4 (START). FUEL FILL SERVICE ENGINE SOON FUEL BRAKE FUEL FILL SERVICE ENGINE SOON FUEL BRAKE 60 70 0 0 0 0 0 0 0 0 km/h 60 70 0 0 0 0 0 0 0 0 km/h...
Page 86 Starting FUEL FILL FUEL – BRAKE SERVICE ENGINE SOON Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is fastened, the STARTING THE ENGINE Whenever you start your vehicle, release the key as soon as the engine starts.
Page 87 depress the accelerator and start the engine while holding the accelerator down to the floor. Release the accelerator when the engine starts. 4. After idling for a few seconds, apply the brake and release the parking brake. Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly.
Page 88 Starting Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch).
Page 89: Driving
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 90 Driving illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with parking brake released.
Page 91 The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. Since the parking brake applies only the rear brakes, the vehicle’s stopping distance will increase greatly and the handling of your vehicle will be adversely affected.
Page 92 Driving TRANSAXLE OPERATION Manual transaxle (if equipped) Using the clutch Vehicles equipped with a manual transaxle have a starter interrupt interlock that prevents cranking of the engine unless the clutch pedal is depressed. When starting a vehicle with a manual transaxle, you must: 1.
Page 93 the clutch pedal to hold your vehicle at a standstill while waiting on a hill. These actions will seriously reduce clutch life. Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Set the parking brake. 3.
Page 94 Driving 4. Turn engine off and remove the key. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts when accelerating (recommended for best fuel economy) Upshifts when cruising (recommended for best fuel economy) Upshifts when accelerating (recommended for best fuel economy)
Page 95 Upshifts when cruising (recommended for best fuel economy) Reverse Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transaxle. Put the gearshift into the neutral position and wait at least three seconds before shifting into R (Reverse).
Page 96 Driving 1. Continue depressing the brake pedal, and remove the shift-lock override cap with a 2.5 cm (1 inch) or longer screwdriver. 2. Insert the screwdriver into the shift-lock override opening and push down. 3. Push and hold the thumb button. 4.
Page 97 Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician.
Page 98 Driving R (Reverse) With the gearshift in R (Reverse), the vehicle will move backward. You should always come to a complete stop before shifting in and out of R (Reverse). N (Neutral) With the gearshift in the N (Neutral) position, the vehicle can be started and is free to roll.
Page 99 (Overdrive) The overdrive position is the normal driving position for an automatic overdrive transaxle. It works the same way as D (Drive) but shifts to a fourth gear-an overdrive gear-when your vehicle cruises at a constant speed for any length of time.
Page 100 Driving L (Low) Use L (Low) when added engine braking is desired or when descending steep hills. The automatic transaxle will shift into the proper gear to ascend any grade without any need to shift to L (Low). Do not go faster than 61 km/h (38 mph) when in this gear. You can upshift from L (Low) to When parking, do not use the gearshift in place of the parking brake.
Page 101 GAWR (Gross Axle Weight Rating): Carrying capacity for each axle system. The GAWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver’s door pillar. GCW (Gross Combined Weight): The combined weight of the towing vehicle (including passengers and cargo) and the trailer.
Page 102 Driving You may add equipment throughout your vehicle if the total weight added is equal to or less than the Total Axle Reserve Capacity (TARC) weight. You should NEVER exceed the Total Axle Reserve Capacity. Always ensure that the weight of passengers, cargo and equipment being carried is within the weight limitations that have been established for your vehicle including both Gross Vehicle Weight and Front and Rear Gross Axle Weight Rating limits.
Page 103 Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transaxle damage, structural damage, loss of control, and personal injury. Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle.
Page 104 Driving Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer. Speed control may shut off if you are towing on long, steep grades. When towing a trailer: Use a lower gear when towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transaxle cooling.
Page 105: Roadside Emergencies
HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. Slide the hazard flasher control to the right to activate the hazard flashers simultaneously. Slide the control to the left to turn the flashers off.
Page 106 Roadside emergencies Driver’s foot well, behind the kick panel. The fuel pump shut-off switch, depending on application, is locatedon the right side of the trunk behind the trunk liner or in the driver’s foot well, behind the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1.
Page 107 FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Always replace a fuse with one that has the specified amperage rating.
Page 108 Roadside emergencies Coupe The fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating HAZARD ROOM ENGINE RADIO DOOR LOCK HORN AIR COND METER WIPER STOP TAIL P. Window (C.B.) (DRL) (DOOR LK) STOP HAZARD HORN TAIL (AIR COND) (SUN ROOF) ROOM ENGINE METER...
Page 109 Fuse/Relay Fuse Amp Location Rating SUN ROOF P. WINDOW 30A CB CIGAR AIR BAG AUDIO FUEL INJ. BLOWER 30A CB Sedan/Wagon The fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating R.WIPER HAZARD Roadside emergencies Power Moonroof Speed Control Power Windows Cigar Lighter Air Bags...
Page 110 Roadside emergencies Fuse/Relay Fuse Amp Location Rating ROOM ENGINE MIRROR DOOR LOCK HORN AIR COND METER WIPER STOP TAIL SUN ROOF CIGAR AIR BAG AUDIO FUEL INJECTOR P. WINDOW 30A CB BLOWER 30A CB Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.
Page 111 Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Care chapter. Coupe The high-current fuses are coded as follows.
Page 112 Roadside emergencies Fuse/Relay Fuse Amp Location Rating OBD-II 10A* FUEL 20A** PUMP HEAD RH 10A** HEAD LH 10A** * Fuse Link Cartridge **Fuse Sedan/Wagon The high-current fuses are coded as follows. HEADLAMP RELAY USE THE DESIGNATED FUSES ONLY Fuse/Relay Fuse Amp Location Rating FUEL INJ.
Page 113 Fuse/Relay Fuse Amp Location Rating COOLING 40A* OBD-II 10A** FUEL 20A** PUMP HEAD RH 10A** HEAD LH 10A** * Fuse Link Cartridge ** Fuse Relays Relays are located in the power distribution box and should be replaced by qualified technicians. CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.
Page 114 Roadside emergencies try to repair the temporary spare tire or remove it from its wheel use the wheel for any other type of vehicle Tire change procedure 1. Park on a level surface, activate hazard flashers and set the parking brake.
Page 115 Automatic Manual 3. Remove the jack, jack handle and spare tire. Roadside emergencies...
Page 116 Roadside emergencies 4. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 5. Put the jack in the jack notch next to the door of the tire you are changing.
Page 117 JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted.
Page 118 Roadside emergencies Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 119 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Page 120 Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
Page 121 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 122 It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Page 123: Maintenance And Care
SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Page 124 Maintenance and care 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Manual transaxle: 1. Set the parking brake, depress the clutch and place the gearshift in 1 (First).
Page 125 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on Automatic transaxle: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park).
Page 126 Maintenance and care 2. Block the wheels to prevent the vehicle from moving unexpectedly. Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Manual transaxle: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral).
Page 127 2. Block the wheels to prevent the vehicle from moving unexpectedly. Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel.
Page 128 Maintenance and care 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood and secure it with the prop rod.
Page 129 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L SOHC I4 engine 1. Engine oil dipstick 2. Brake fluid reservoir 3. Transmission fluid dipstick (automatic transaxle) 4. Battery 5. Air filter assembly 6. Engine oil filler cap 7. Power steering fluid reservoir 8.
Page 130 Maintenance and care 2.0L DOHC Zetec engine 1. Transmission fluid dipstick (automatic transaxle) 2. Battery 3. Air filter assembly 4. Engine oil filler cap 5. Engine oil dipstick 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9.
Page 131 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (automatic transaxle) or 1st (manual transaxle).
Page 132 Maintenance and care If the oil level is between the ADD and FULL marks, the oil level is acceptable. DO NOT ADD OIL. If the oil level is below the ADD mark, add enough oil to raise the level within the ADD-FULL range. Oil levels above the F in FULL may cause engine damage.
Page 133 Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced.
Page 134 3. If necessary, add brake fluid until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic.
Page 135 Maintenance and care CLUTCH FLUID (IF EQUIPPED) Check the clutch fluid level. Refer to the Scheduled Maintenance Guide for the service interval schedules. The clutch master cylinder and brake master cylinder are part of the same system; both are refillable through the brake master cylinder with brake fluid.
Page 136 Maintenance and care WINDSHIELD WASHER FLUID Checking and adding washer fluid Coupe Sedan/Wagon Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way.
Page 137 Checking and adding washer fluid for the liftgate (if equipped) The rear reservoir is located on the passenger side of the storage compartment behind the access cover. Refill this reservoir with the same fluid you use for your windshield. ENGINE COOLANT Coupe Sedan/Wagon Check the level of the engine coolant in the reservoir.
Page 138 Adding engine coolant Use only Ford Premium Engine Coolant E2FZ-19549–AA (in Oregon, F5FZ-19549–CC, in Canada, Motorcraft CXC-10) or a premium engine coolant that meets Ford specification ESE-M97B44–A.
Page 139 Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44–A, and use of such coolant may harm engine and cooling system components.
Page 140 Maintenance and care Severe winter climate If you drive in extremely cold climates (less than –36°C [–34°F]), it may be necessary to increase the coolant concentration above 50%. Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle is such that the coolant will not freeze at the temperature level in which you drive during winter months.
Page 141 Maintenance and care 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5.
Page 142 Maintenance and care Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the outside temperatures are above 10°C (50°F). Correct fluid level The transmission fluid should be checked at normal operating temperatures 66°C-77°C (150°F-170°F) on a level surface.
Page 143 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
Page 144 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules.
Page 145 When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 146 Maintenance and care Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. AIR FILTER MAINTENANCE Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the air filter element.
Page 147 Maintenance and care WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades. Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild...
Page 148 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 149 Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 150 If you do not follow these precautions, your vehicle may not drive properly and safely. Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford.
Page 151 Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle.
Page 152 Maintenance and care WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 153 Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. Fuels can also be harmful if absorbed through the skin.
Page 154 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 155 It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high quality fuel. Cleaner air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates up to 10% ethanol or 15% MTBE.
Page 156 Maintenance and care Your “Service Engine Soon” indicator may come on. For more information on the “Service Engine Soon” indicator, refer to the Instrumentation chapter. Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician. Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the fuel filter.
Page 157 Allow three automatic click-offs when filling. Always use fuel with the recommended octane rating. Use a known quality gasoline, preferably a national brand. Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. Have the vehicle loading and distribution the same every time.
Page 158 Maintenance and care Idling for long periods of time (greater than one minute) may waste fuel. Anticipate stopping; slowing down may eliminate the need to stop. Sudden or hard accelerations may reduce fuel economy. Slow down gradually. Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15% less fuel than traveling at 105 km/h [65 mph]).
Page 159 Adding certain accessories to your vehicle (for example bug deflectors, rollover/light bars, running boards, ski/luggage racks) may reduce fuel economy. Using fuel blended with alcohol may lower fuel economy. Fuel economy may decrease with lower temperatures during the first 12–16 km (8–10 miles) of driving. Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain.
Page 160 Maintenance and care If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 161 Next, at least 20 minutes driving in stop-and-go, city-type traffic with at least four idle periods. Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature.
Page 162 Maintenance and care Replacing headlamp bulbs 1. Make sure that the headlamps are turned OFF. Coupe Sedan/wagon 2. Open the hood and disconnect the headlamp wiring socket from the in-line connector. This will make it easier to change the bulb. 3.
Page 163 Maintenance and care 5. Remove the bulb retaining ring by rotating it counterclockwise. 6. Without turning, remove the old bulb from the lamp assembly by pulling it straight back out of the lamp assembly and replace. 7. Install the new bulb in lamp assembly by pushing straight in with the bulb’s plastic base facing upward.
Page 164 Maintenance and care Replacing foglamp bulbs 1. Remove the bulb socket from the foglamp by turning counterclockwise. 2. Disconnect the electrical connector from the foglamp bulb. 3. Connect the electrical connector to the new foglamp bulb. 4. Install the bulb socket in the foglamp turning clockwise.
Page 165 Maintenance and care Tail lamp/Rear turn signal lamp bulbs-Except Wagon The tail lamp and the turn signal lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb. 1.
Page 166 Maintenance and care Tail lamps/Rear turn signal lamp bulbs-Wagon The tail lamp and the turn signal bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb. 1.
Page 167 INTERIOR BULBS Dome lamp 1. Remove the lamp lens by applying pressure to both tabs at the top of the lamp and pulling lens downward. 2. Pull out the burned-out bulb and install a new one. 3. Install the lamp lens by applying pressure to both sides of the lamp lens and popping the lamp lens up on the assembly.
Page 168 Maintenance and care AIMING THE HEADLAMPS Your vehicle is equipped with a Vehicle Headlamp Aim Device (VHAD) on each headlamp. Each headlamp may be properly aimed in the vertical (up/down) and the horizontal (left/right) directions using your VHAD system. The headlamps on your vehicle are properly aimed at the assembly plant.
Page 169 Repeat the above process to the other headlamp, if necessary. CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Maintenance and care...
Page 170 Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), touch-up paint (#ALBZ-19500–XXXXA), or aerosol paint spray (#ALAZ-19500– XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring. Observe the application instructions on the products.
Page 171 Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately. Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents.
Page 172 Maintenance and care Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners.
Page 173 For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label.
Page 174: Capacities And Specifications
** If a spark plug is removed for inspection, it must be reinstalled in the same cylinder.If a spark plug needs to be replaced, use only spark plugs with the same service part number suffix letter as shown on the engine decal. REFILL CAPACITIES Ford Part Fluid Name Brake fluid High...
Page 175 Ultra-Clear washer fluid Windshield Washer Concentrate Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. LUBRICANT SPECIFICATIONS Ford Part...
Page 176 Windshield Ultra-Clear washer fluid Windshield Washer Concentrate DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA, meeting Ford specification WSS-M97B44-D (orange in color) Refer to Adding engine coolant, in the Maintenance and Care chapter. ENGINE DATA Engine Cubic inches Horsepower...
Page 177 VEHICLE DIMENSIONS Vehicle Coupe mm (in) Sedan mm (in) Wagon mm dimensions (1) Overall 4 451.0 (175.2) length (2) Overall 1 712.0 (67.4) width (3) Overall 1 328.4 (52.3) height (4) Wheelbase 2 499.0 (98.4) (5) Track - 1 435.1 (56.5) Front (5) Track - Rear 1 435.1 (56.5) Coupe and Sedan models...
Page 178 Capacities and specifications Coupe model Sedan model...
Page 179 Wagon model Wagon model Capacities and specifications...
Page 180: Certification Label
Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block and transmission. MFD. BY FORD MOTOR CO. IN U.S.A. DATE: XXXXX GVWR:XXXXX LB/ XXXXX KG FGAWR: XXXXXX/XXXXXXX RGAWR: XXXXXXX/XXXXXXX...
Page 181: Customer Assistance
GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: 24–hours, seven days a week for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.) of three years or 60,000 km (36,000 miles),...
Page 182 5,200 participating Ford, Lincoln-Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Please contact your dealer for further information. Since this information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options.
Page 183 Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company dealership authorized for warranty repairs.
Page 184 Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Page 185 Ford or Lincoln/Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln-Mercury dealership management, recognized for their business leadership qualities. What the Board needs...
Page 186 Ford Motor Company the names (if known) of all the people you contacted at the...
Page 187 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 188 Customer assistance nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: (313) 594-4857 FAX: (313) 390-0804 If you are in another foreign country, contact the nearest Ford dealership.
Page 189 In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigid engineering and safety specifications. Ford accessories are warranted for...
Page 190 Customer assistance Travel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adaptors Fog lights Framed luggage covers Heavy-duty battery Neutral towing transfer case kit (Explorer 4.0L only) Off road lights Pickup box rails Removable luggage rack Removable luggage rack adapters Retractable bed hooks and loops Running boards...
Page 191 Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rallye bars Rear air deflectors Rear decklid spoilers Side window air deflectors Spare tire lock Step bumpers Step/sill plates...
Page 192 (Citizens band [CB] transceivers, garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle’s operation.) Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment. ORDERING ADDITIONAL OWNER’S LITERATURE...
Page 193: Reporting Safety Defects
However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.
Page 194: Index
...94 Coolant ...137,139,140 checking and adding ...138 refill capacities ...139,174 specifications ...175,176 Customer Assistance ...181 Ford accessories for your vehicle ...188 Ford Extended Service Plan ...182 Getting assistance outside the U.S. and Canada ...187 Getting roadside assistance ...181...
Page 195 Getting the service you need ...183 Ordering additional owner’s literature ...192 The Dispute Settlement Board ...184 Defrost rear window ...42 Dipstick engine oil ...130 Driving under special conditions through water ...102 Emergencies, roadside jump-starting ...117 Emission control system ...159 Engine ...176,177 check engine/ service engine soon light ...7 coolant ...137...
Page 196 Index Headlamps ...42 aiming ...168,169 bulb specifications ...167 daytime running lights ...43 flash to pass ...43 high beam ...9,43 replacing bulbs ...162 turning on and off ...42 warning chime ...10 Heating ...37 heater only system ...37 heating and air conditioning system ...39 Hood ...127 Ignition ...176,177 positions of the ignition ...42...
Page 197 illuminated entry ...58 locking/unlocking doors ...55,56 opening the trunk ...56 panic alarm ...57 replacement/additional transmitters ...58 replacing the batteries ...57 Roof rack ...104 Safety belts (see Safety restraints) ...10,65,66,67,68 Safety Compliance Certification Label ...180 Safety defects, reporting ...193 Safety restraints ...65,66,67,68 cleaning the safety belts ...70,173 extension assembly ...69 for adults ...66,67...
Page 200: Filling Station Information
Power steering fluid capacity Automatic transaxle capacity Manual transaxle capacity Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter.

Ford 1999 Escort Owner's Manual

Quick Links

Related Manuals for Ford 1999 Escort

Summary of Contents for Ford 1999 Escort

Table of Contents