Page 1 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.
Page 2: Introduction
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning Engine exhaust, some if its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm.
Page 3 INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. SPECIAL NOTICES...
Page 4 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert Fasten Safety Belt Air Bag-Side Child Seat Installation Warning Brake System Brake Fluid - Non-Petroleum Based Master Lighting Switch Fog Lamps-Front Fuel Pump Reset Windshield Defrost/Demist Power Windows...
Page 5 Vehicle Symbol Glossary Panic Alarm Engine Coolant Do Not Open When Avoid Smoking, Flames, or Sparks Explosive Gas Power Steering Fluid Emission System Passenger Compartment Air Filter Introduction Engine Oil Engine Coolant Temperature Battery Battery Acid Fan Warning Maintain Correct Fluid Level Engine Air Filter Jack...
Page 6: Instrumentation
Instrumentation Driver air bag (pg. 75) Headlamp control (pg. 18) Rear defroster* (pg. 19) Turn signal and wiper/washer control (pg. 40) * if equipped Instrument cluster (pg. 8) 60 70 RPMX1000 80 100 120 km/h SELECT/RESET 0 0 0 0 0 FUEL DOOR SERVICE THEFT...
Page 7 Climate control system (pg. 20) Overdrive off switch (pg. 104) Instrumentation Electronic sound system (pg. 23)
Page 8: Warning Lights And Chimes
Instrumentation WARNING LIGHTS AND CHIMES Base instrument cluster 60 70 80 100 120 FUEL DOOR SERVICE THEFT ENGINE Optional instrument cluster 120 140 FUEL DOOR THEFT Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on.
Page 9 Instrumentation position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service.
Page 10 Instrumentation to check the bulb. If it comes on after the engine is started, one of the engine’s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted. The vehicle will usually be drivable and will not require towing.
Page 11 Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge (refer to Fuel Gauge in this chapter for more information).
Page 12 Instrumentation Traction Control active Momentarily illuminates when the ignition is turned to ON. It also illuminates when the Traction Control system begins applying and releasing the brakes and adjusting the engine characteristics to limit a wheelspin condition. It will be lit for a minimum of four seconds or for the duration of the Traction Control event.
Page 13: Headlamps On Warning Chime
added. This lamp will also illuminate when the ignition is turned to ON and the engine is off. For more information on adding engine coolant, refer to Engine coolant in the Maintenance and care chapter. Safety belt warning chime Sounds to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter.
Page 14: Fuel Gauge
Instrumentation Optional instrument cluster gauges 120 140 FUEL DOOR SERVICE THEFT Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
Page 15 This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. Speedometer Indicates the current vehicle speed. Base instrument cluster Optional instrument cluster Odometer Registers the total...
Page 16 Instrumentation Base instrument cluster Optional instrument cluster Trip odometer Registers the kilometers (miles) of individual journeys. Press and release the reset button until a “T” appears in the display (this represents the trip mode). Press and hold the button for three seconds to reset.
Page 17 Instrumentation Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range (the area between the “L” and “H”). If the gauge indicates low pressure, stop the vehicle as soon as safely possible and switch off the engine immediately.
Page 18: Controls And Features
Controls and features HEADLAMP CONTROL Pull the headlamp control toward you to the first position to turn on the parking lamps, tail lamps, license plate lamps and marker lamps. Pull the headlamp control toward you to the outer position to turn on the headlamps (in addition to the previous lamps).
Page 19 Controls and features PANEL DIMMER CONTROL To adjust the brightness of the instrument panel: Rotate clockwise/ counterclockwise when the headlamp control is in the parking lamp or low-beam position. To turn on the courtesy lamps: Rotate fully counterclockwise. REAR WINDOW DEFROSTER (IF EQUIPPED) The rear defroster control is located on...
Page 20 Controls and features CLIMATE CONTROL SYSTEM Manual heating and air conditioning system Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Page 21 Controls and features faster. Airflow will be from the instrument panel registers. This mode can also be used to reduce undesirable odors from entering the vehicle. A/C-Uses outside air to cool the vehicle. It is quieter than MAX A/C but not as economical. Airflow will be from the instrument panel registers.
Page 22 Controls and features Operating tips In humid weather, select This will reduce fogging on your windshield. After a few minutes, select any desired position. To reduce humidity buildup inside the vehicle, don’t drive with the climate control system in the OFF or MAX A/C position.
Page 23 Controls and features USING YOUR AUDIO SYSTEM AM/FM Stereo/Cassette/Premium Sound FM 1 POWER AUDIO AM/FM – VOLUME Power control Press the control to turn the audio system on or off. Volume control Press the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 24 Controls and features Tune adjust in radio mode Tune adjust allows you to tune in a particular radio station. You can manually locate the station by using the Automatic Music Search (AMS) button. Press the AMS control until the display shows TUNE.
Page 25 Controls and features Press to listen to the previous selection on the tape. Press to listen to the next selection on the tape. The tape deck stops and returns to play mode when the AMS circuit senses a blank section on the tape. In order to ensure proper operation of the AMS feature, the tape MUST have a blank section of at least 4 seconds duration between programs.
Page 26 Controls and features held in memory on the control you selected. Repeat the steps for each station memory preset button you want to set. If the battery is disconnected, the memory preset stations will need to be reset. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output.
Page 27 Controls and features Press the (+) side of the volume control to shift sound to the right speakers. Press the (−) side of the volume control to shift sound to the left speakers. Speaker fade adjust Speaker sound distribution can be adjusted between the front and rear speakers.
Page 28: Setting The Clock
Controls and features Tape eject Press the control to stop and eject a tape. Dolby noise reduction Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby noise reduction. Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation.
Page 29 Controls and features Power control Press the control to turn the audio system on or off. Volume control Press the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 30 Controls and features Press and hold down through the frequencies. Seek function The seek function control works in radio or tape mode. Seek function in radio mode This feature allows you to automatically select listenable stations up or down the frequency band. Press to find the next listenable station down the frequency band.
Page 31 Controls and features Use the SEEK button to scan up or down the frequency band. Press to find the next listenable station down the frequency band. Press to find the next listenable station up the frequency band. Scan function in tape mode This feature allows you to scan the tape currently playing,...
Page 32 Controls and features 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. If the battery is disconnected, the memory preset stations will need to be reset. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output.
Page 33 Controls and features Press the (+) side of the volume control to shift sound to the right speakers. Press the (−) side of the volume control to shift sound to the left speakers. Speaker fade adjust Speaker sound distribution can be adjusted between the front and rear speakers.
Page 34 Controls and features Press the control to fast forward the tape. Once the end of the tape is reached, tape direction reverses and the opposite side of the tape plays. Tape eject Press the control to stop and eject a tape. Dolby noise reduction Dolby noise reduction reduces the amount of...
Page 35 Controls and features Single Disc CD Player EJECT DISC Power and volume control The compact disc player operates when the audio system is on and a CD is inserted (label side up). The volume is controlled by the VOLUME control on the audio system.
Page 36 Controls and features approximately eight seconds. This continues until you press the SCAN control a second time or eject the CD. While in the scan mode, the display flashes SCAN. Reverse/fast forward To quickly search for a REV/FF particular point in a selection, press the right side of the REV/FF control (to fast forward) or the left side (to reverse).
Page 37 Controls and features Shuffle feature The shuffle feature plays all tracks on the current CD in random order. Press the SHUFFLE control to start this feature. Random order play will continue until the control is pressed again. Eject Push the EJECT control to stop CD play, eject the CD, and resume radio or tape...
Page 38 Controls and features Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion. CD and CD player care Handle discs by their edges only.
Page 39 Controls and features and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area. Radio reception factors Three factors can affect radio reception: Distance/strength.
Page 40 Controls and features TRUNK REMOTE CONTROL The remote trunk release control is located in the glove compartment. Press to open trunk. TURN SIGNAL CONTROL Push down to activate the left turn signal. Push up to activate the right turn signal. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the...
Page 41 FLASH TO PASS Pull toward you to activate and release to deactivate. POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal.
Page 42 Controls and features Never adjust the steering wheel when the vehicle is moving. SPEED CONTROL To turn speed control on Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
Page 43 Controls and features To set a speed Press SET/SET ACC/ SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
Page 44 Controls and features Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET/SET ACC/SET ACCEL. You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed.
Page 45 Controls and features Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. To return to a previously set speed Press RES/RSM/ RESUME. For RES/ RSM/RESUME to operate, the vehicle speed must be faster...
Page 46 Controls and features POWER WINDOWS Press and hold the rocker switches to open and close windows. Press the top portion of the rocker switch to close. Press the bottom portion of the rocker switch to open. Express down To make the driver window open fully without holding the window control, press...
Page 47 Controls and features for the driver’s press the control. Press the control again to restore the window controls. POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors. POWER SIDE VIEW MIRRORS (IF EQUIPPED) To adjust your mirrors: 1.
Page 48 Controls and features Use only soft cups in the cupholder. Hard objects can injure you in a collision. Foglamp control (if equipped) Turn on the parking lamps or the low-beam headlamps. Press the top portion of the foglamp control, located on the center console, to activate the foglamps.
Page 49 Controls and features 3. Unclamp the top from the windshield header at both the right and left sides by pulling each clamp rearward until the hook in the windshield header is free. The clamps are flush with the header when in the closed position.
Page 50 Controls and features 2. Push boot forward until rear attachment engages under molding. 3. Push forward flap of boot until both clips engage under trim panel edge. Repeat on other side of vehicle. 4. Tuck side attachments under molding. Repeat on other side of vehicle.
Page 51 Controls and features Raising the convertible top The convertible top will not operate unless the parking brake is engaged. Do not raise the top while the vehicle is moving because the top may be severely damaged. To raise the convertible top: 1.
Page 52 Controls and features AUXILIARY POWER POINT The power point is an additional power source for electrical accessories. TRACTION CONTROL This control can be used to turn the TRAC Traction Control CTRL or off. Refer to the Traction Control section of the Driving chapter for more information.
Page 53 Controls and features The transmission will operate in all gears except overdrive. To return to normal overdrive mode, press the Transmission Control Switch again. The O/D OFF indicator light will no longer be illuminated. When you shut off and re-start your vehicle, the transmission will automatically return to normal (Overdrive) mode.
Page 54 Controls and features Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. With the all-door remote entry system, press the control a second time within three seconds to unlock the passenger door. Locking the doors Press this control to lock all doors.
Page 55 Controls and features Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada.
Page 56 Controls and features Replacing lost transmitters Take all your vehicle’s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed into memory), perform the following procedure: To reprogram the transmitters, place the key in the ignition and turn from OFF to ON eight times in rapid succession (within 10 seconds) ending in ON.
Page 57 Controls and features To replace the batteries: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new batteries down. Refer to the diagram inside the transmitter unit.
Page 58 OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the encoded ignition key is an approved Ford encoded ignition key. Spare SecuriLock keys can be purchased from...
Page 59 Controls and features of eight keys). Your dealership can program your new SecuriLock key(s) to your vehicle or you can do it yourself using the following simple procedure. To program a new SecuriLock will need two previously programmed SecuriLock keys (keys that already operate your vehicle’s engine).
Page 60 Controls and features key/valet key) into the ignition and turn the ignition from OFF to ON (maintain ignition in ON for at least one second). This step will program your new SecuriLock key. 6. To program additional SecuriLock this procedure from step 1. If the programming procedure was successful, the new SecuriLock key(s) will start the vehicle’s...
Page 61 Controls and features To open the luggage compartment door (lid) from the inside, pull the illuminated “T” shaped handle and push up on the trunk lid. The material that the handle is made of will glow for hours in the darkness of the luggage compartment following brief exposure to ambient...
Page 62: Seating And Safety Restraints
Seating and safety restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 63 Seating and safety restraints Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Page 64 Seating and safety restraints The control is located on the front outboard corner of the driver’s seat. Press front to raise or lower the front portion of the seat cushion. Press rear to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down.
Page 65 Seating and safety restraints The rotating boot on the front seat belt is designed to allow rear seat entry/exit. To enter the rear seat: 1. Remove seat belt from seat belt holder on top of front seat. 2. Rotate the safety belt boot rearward.
Page 66 Seating and safety restraints To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Page 67 Seating and safety restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Combination lap and shoulder belts Before fastening the safety belt, make sure the shoulder belt passes through the belt holder on the top of the seatback.
Page 68 Seating and safety restraints The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to...
Page 69 Seating and safety restraints How to use the automatic locking mode Buckle the combination lap and shoulder belt. Grasp the shoulder portion and pull downward until the entire belt is extracted. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Page 70 Seating and safety restraints Safety belt extension assembly If the safety belt assembly is too short, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer at no cost.
Page 71 Seating and safety restraints Belt minder (if equipped) The Belt Minder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster.
Page 72 I’m not going 3 of 4 fatal crashes occur within 25 miles of home. Belts are Ford designs its safety belts to enhance uncomfortable comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible;...
Page 73 Seating and safety restraints Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase risk of injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below.
Page 74 Seating and safety restraints 2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes) Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated. 3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled.
Page 75 This information will assist Ford in the servicing of your vehicle and may help Ford better understand real world collisions and further improve the safety of future vehicles.
Page 76 Seating and safety restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module.
Page 77 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body...
Page 78 Seating and safety restraints Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Page 79 Seating and safety restraints amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic. While the system is designed to help reduce serious injuries, contact with a deploying air bag may also cause abrasions, swelling or temporary hearing loss.
Page 80 Seating and safety restraints system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Page 81 Seating and safety restraints Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children.
Page 82 Do not leave children, unreliable adults, or pets unattended in your vehicle. To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards.
Page 83 Refer to Automatic locking mode (passenger side front and outboard rear seating positions) (if equipped). Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 84 Seating and safety restraints Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. Installing child safety seats in combination lap and shoulder belt seating positions If you must use a...
Page 85 Seating and safety restraints Children 12 and under should be properly restrained in the rear seat whenever possible. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to...
Page 86 Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 87 Seating and safety restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap.
Page 88 Seating and safety restraints 3. Locate the correct anchor for the selected seating position as shown previously. For Coupe only: 4. Open the tether anchor covers. 5. Clip the tether strap to the anchor as shown. For Convertible only: The tether anchors on the convertible are located on the lower backside of the...
Page 89 Seating and safety restraints 5. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 6. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat.
Page 90 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 91 Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Do not allow the vehicle to idle for more than 10 minutes at high engine RPM.
Page 92: Starting The Engine
Starting 3. Turn the key to 4 (ON) without turning the key to 5 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns freely. This condition may occur when: front wheels are turned front wheel is against the curb steering wheel is turned when getting in or out of...
Page 93 2. If the temperature is above –12°C (10°F) and the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. 3. If the temperature is below -12° C (10° F) and the engine does not start in 15 seconds on the first try, turn the key OFF and wait 10 seconds and try again.
Page 94 Starting If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you. Have the exhaust and body ventilation systems checked whenever: the vehicle is raised for service.
Page 95: Driving
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 96 Driving The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency. The wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking with loss of front braking traction.
Page 97 stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop. We recommend that you familiarize yourself with this braking technique. However, avoid taking any unnecessary risks. Hydraulic brake booster system (Hydroboost) The Hydroboost system receives fluid pressure from the power steering pump to provide power assist during braking.
Page 98 Driving (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First Gear) (manual transmission). The parking brake is not recommended to stop a moving vehicle.
Page 99 controlled by automatically applying and releasing the rear brakes in conjunction with engine torque reductions. Engine torque reduction is realized via the fully electronic spark and fuel injection systems. This process is very sensitive to driving conditions and very fast acting. The rear wheels “search” for optimum traction several times a second and adjustments are made accordingly.
Page 100 Driving STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. To prevent damage to the power steering pump: Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
Page 101 If it is necessary to use the above procedure to move the gearshift lever, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly. Refer to Fuses and relays in the Roadside emergencies chapter. Do not drive your vehicle until you verify that the brakelamps are working.
Page 102 Driving Driving with an automatic overdrive transmission with console gearshift and O/D off switch Your automatic overdrive transmission provides fully automatic operation in either D (Overdrive) or with the O/D OFF switch depressed. Driving with the gearshift lever in D (Overdrive) gives the best fuel economy for normal driving...
Page 103 Understanding gearshift positions P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This position locks the transmission and prevents the rear wheels from turning. Always set the parking brake fully and make sure the gearshift lever is latched in P (Park).
Page 104 Driving (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through four. (Overdrive) can be deactivated by pressing the transmission control switch on the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster.
Page 105 Driving To return to (Overdrive) mode, press the transmission control switch. The O/D OFF indicator will no longer be illuminated. Each time the vehicle is started, the transmission will automatically return to normal overdrive mode. Every time the vehicle is shut off and restarted, you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired.
Page 106 Driving MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch Vehicles equipped with a manual transmission have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. When starting a vehicle with a manual transmission, you must: 1.
Page 107 Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill while waiting on a hill. These actions will greatly reduce clutch life. Recommended shift speeds Do not downshift into 1 (first) when your vehicle is moving faster then 24 km/h (15 mph).
Page 108 Driving 4. Turn the ignition key to position 3 (OFF). Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Reverse You must be at a complete stop to shift into R (Reverse).
Page 109 If R (Reverse) is not engaged, push the clutch pedal down and put the gearshift back into Neutral. Then, release the clutch pedal for a moment and repeat steps 3 through 6. Removing key from ignition Turn the ignition key to position 3 (OFF).
Page 110 Driving Payload: Combined maximum allowable weight of cargo, passengers and optional equipment. The payload equals the gross vehicle weight rating minus base curb weight. GVW (Gross Vehicle Weight): Base curb weight plus payload weight. The GVW is not a limit or a specification.
Page 111 Trailer Weight Range: Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating. Remember to figure in the tongue load of your loaded trailer when figuring the total weight. Do not exceed the GVWR or the GAWR specified on the certification label.
Page 112 Driving TRAILER TOWING Your vehicle is capable of towing a trailer up to 454 kg (1 000 lbs.) gross trailer weight with a maximum tongue load of 45 kg (100 lbs.). Do not tow a trailer until your vehicle has been driven at least 800 km (500 miles).
Page 113 adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase.
Page 114 Driving your Scheduled Maintenance guide for more information. Trailer towing tips Practice turning, stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles.
Page 115 If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the driveshaft. Ford recommends the driveshaft be removed/installed only by a qualified technician. See your local dealer for driveshaft removal/installation.
Page 116: Roadside Emergencies
Ford dealership, or your selling dealer if within 25 kms (15.5 miles) of the nearest Ford Dealership (one tow per disablement). Even non-warranty related tows, like accidents or getting stuck in the mud or snow, are covered (some exclusions apply, such as impound towing or repossession).
Page 117 Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance Club brochure or by calling 1–877–294–CLUB...
Page 118 Roadside emergencies After a collision, if the engine cranks but does not start, the fuel pump shut-off switch may have been activated. The fuel pump shut-off switch is located on the left side of the trunk behind the trunk liner. Use the following procedure to reset the fuel pump shut-off switch.
Page 119 Roadside emergencies Check the appropriate fuses before replacing any electrical components. Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color Fuse Mini...
Page 120 Roadside emergencies OWNERS The fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating — — — — — MANUAL FUSE INFO Passenger Compartment Fuse Panel Description Cigar Lighter Engine Controls Not Used RH Low Beam Headlamp Instrument Cluster, Traction Control Switch Starter Motor Relay GEM, Interior Lamps...
Page 121 Roadside emergencies Fuse/Relay Fuse Amp Location Rating — — — 20A CB — Passenger Compartment Fuse Panel Description Power Mirror Switch, GEM, Anti-Theft Relay, Power Door Locks, Door Ajar Switches Convertible Top Switch Instrument Cluster and Engine Control Memory Not Used A/C Clutch, Defogger Switch Climate Control Blower Motor Luggage Compartment Lid...
Page 122 Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Page 123 Roadside emergencies The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating Relay 1 — Relay 2 — Relay 3 — Relay 4 — Relay 5 — 50A** (4.6L), 30A CB (3.8L) 30A** 40A** 40A** 40A** 40A** 30A** 50A** 20A** 30A**...
Page 124 Roadside emergencies Fuse/Relay Fuse Amp Location Rating — 30A** 20A** 25A CB * Mini Fuses ** Maxi Fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road.
Page 125 Roadside emergencies try to repair the temporary spare tire or remove it from its wheel use the wheel for any other type of vehicle Tire change procedure To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
Page 126 Roadside emergencies 4. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 5. Put the jack in the jack notch next to the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground.
Page 127 If the lug wrench/lug nut key assembly is lost, see your nearest Ford or Lincoln/Mercury dealer who has access to the master set of keys. Do not use an impact wrench with the anti-theft key.
Page 128 Roadside emergencies 2. Place the lug nut wrench over the lug nut key and apply pressure on the key with the wrench. 3. Install the lug nut. JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage.
Page 129 Roadside emergencies Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 130 Roadside emergencies 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.
Page 131 Roadside emergencies 1. Remove the jumper cable from the ground metal surface. 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4.
Page 132 It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If your vehicle is to be towed from the rear using...
Page 133: Maintenance And Care
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Page 134 Maintenance and care 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First).
Page 135 Maintenance and care OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. HOOD 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
Page 136 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.8L OHV V6 engine 1. Engine oil filler cap 2. Engine oil dipstick 3. Brake fluid reservoir 4. Power distribution box 5. Windshield washer fluid reservoir 6. Battery 7. Power steering fluid reservoir 8.
Page 137 Maintenance and care 4.6L SOHC V8 engine 1. Engine oil dipstick 2. Brake fluid reservoir 3. Power distribution box 4. Windshield washer fluid reservoir 5. Battery 6. Engine coolant reservoir 7. Power steering fluid reservoir 8. Engine oil filler cap 9.
Page 138 Maintenance and care 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick).
Page 139 Maintenance and care 3.8L OHV V6 engine 4.6L SOHC V8 engine Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated.
Page 140 If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application.
Page 141 Maintenance and care BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the Scheduled Maintenance Guide for the service interval schedules. 3.8L OHV V6 engine 4.6L SOHC V8 engine 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir.
Page 142 Maintenance and care 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes.
Page 143 ENGINE COOLANT Checking engine coolant Your engine’s cooling system has been factory-filled with a 50/50 mixture of distilled water and Ford Premium Engine Coolant E2FZ-19549-AA (in Canada, Motorcraft CXC-10), or an equivalent premium engine coolant that meets Ford...
Page 144 Maintenance and care A 50/50 mixture of distilled water and Ford Premium Engine Coolant provides: maximum cooling system efficiency. freeze protection down to -36° C (-34° F). boiling protection up to 129° C (265° F). protection against rust and other forms of corrosion.
Page 145 E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B) or a premium engine coolant that meets Ford specification ESE-M97B44-A. DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA (orange in color). DO NOT USE a DEX-COOL engine coolant or an equivalent engine coolant that meets Ford specification WSS-M97B44-D.
Page 146 Maintenance and care DO NOT MIX recycled coolant and conventional coolant together in your vehicle. Mixing of engine coolants may harm your engine’s cooling system. The use of an improper coolant may harm engine and cooling system components and may void the warranty of your vehicle’s engine cooling system.
Page 147 Maintenance and care Have your dealer check the engine cooling system for leaks if you have to add more than 1.0 liter (1.0 quart) of engine coolant per month. If equipped with the 3.8L V6 engine, to avoid scalding hot steam or coolant from being released from the engine cooling system, never remove the radiator cap from the radiator while the engine is running or hot.
Page 148 Maintenance and care which can be purchased from your dealer. Engine coolant refill procedure-3.8L V6 engine Use the following procedure when refilling the cooling system of a vehicle equipped with a 3.8L V6 engine. Failure to follow this warning may result in damage to the engine and engine cooling system.
Page 149 Maintenance and care 12. Add a 50/50 mixture of engine coolant and distilled water to the radiator until full. 13. Reinstall the radiator cap. 14. Check the coolant level in the reservoir before you drive your vehicle the next few times (with the engine cool).
Page 150 “cold fill level” as listed on the reservoir. Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44-A.
Page 151 Maintenance and care protection characteristics of the engine coolant and may cause engine damage. refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months.
Page 152 Maintenance and care If your vehicle is equipped with the 3.8L V6 engine, check the power steering fluid level with the engine at normal operating temperature. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near...
Page 153 Maintenance and care If your vehicle is equipped with a 4.6L V8 engine, check the power steering fluid level with the engine at ambient temperature. Allow at least one-half hour after driving for the power steering fluid to cool. 1. Start the engine and allow the engine to idle.
Page 154 Maintenance and care been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature.
Page 155 Maintenance and care You can check the fluid without driving if the ambient temperature is above 10°C (50°F). However, if fluid is added at this time, an overfill condition could result when the vehicle reaches normal operating temperature. The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]).
Page 156 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
Page 157 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules.
Page 158 Maintenance and care Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation. When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting...
Page 159 Maintenance and care 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6.
Page 160 Maintenance and care windshield wiper solution or a mild detergent. Rinse thoroughly with clean water. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents. Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service...
Page 161 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 162 Maintenance and care Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 163 Maintenance and care Tire rotation Because your vehicle’s tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the Scheduled Maintenance Guide. If you notice that the tires wear unevenly, have them checked. 15 or 16 inch four tire rotation 17 inch four tire...
Page 164 Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over.
Page 165 Maintenance and care chains. Use chains on the tires only in an emergency or if the law requires them. Follow these guidelines when using snow tires and chains: Chains may damage aluminum wheels. Use only Cable Type chains with size P225/55R16 or 245/45ZR17 tires.
Page 166 Maintenance and care The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel...
Page 167 Maintenance and care vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury. Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention.
Page 168 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used.
Page 169 Maintenance and care The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel...
Page 170 Ask your fuel supplier about gasolines that meet the World-wide Fuel Charter. Cleaner air Ford approves the use of reformulated “cleaner-burning” gasolines to improve air quality. These gasolines may contain oxygenates up to 10% ethanol or 15% MTBE.
Page 171 Maintenance and care If you have run out of fuel: You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. Your “Service Engine Soon”...
Page 172 Maintenance and care The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty. Empty reserve is the small amount of usable fuel remaining in the fuel tank after the fuel gauge indicates empty.
Page 173 Maintenance and care 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy: Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used.
Page 174 Maintenance and care Revving the engine before turning it off may reduce fuel economy. Using the air conditioner or defroster may reduce fuel economy. You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs.
Page 175 Maintenance and care Using fuel blended with alcohol may lower fuel economy. Fuel economy may decrease with lower temperatures during the first 12–16 km (8–10 miles) of driving. Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal.
Page 176 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover.
Page 177 Maintenance and care Please consult your “Warranty Guide” for complete emission warranty information. Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the Warning Lights and Chimes section of the Instrumentation chapter.
Page 178 Maintenance and care Turn signals Backup lamps License plate lamp Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Replacing headlamp bulbs To remove the headlamp bulb: 1.
Page 179 Maintenance and care 6. Without turning, remove the old bulb from the lamp assembly by gently pulling it straight out of the lamp assembly. To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Page 180 Maintenance and care 2. Open the hood. 3. At the back of the headlamp, pull two retainer pins up to release the headlamp assembly. 4. Pull headlamp assembly forward disengaging the lamp from the rear snap retainers to expose the back of the bulb.
Page 181 Maintenance and care Replacing foglamp bulbs The halogen bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope.
Page 182: Map Lamps
Maintenance and care interior overhead lamp map lamp For bulb replacement, see a dealer or qualified technician. Map lamps For bulb replacement, see a qualified service technician or your dealer. Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.”...
Page 183 Maintenance and care AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. Vertical aim adjustment 1.
Page 184 6. Close the hood and turn off the lamps. CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water.
Page 185 Finishing Kit (#F7AZ-19K507–BA), Lacquer Touch-up Paint (#ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring. Observe the application instructions on the products.
Page 186 Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry...
Page 187 Ford Ultra-Clear Spray Glass Cleaner, (E4AZ-19C507–AA), available from your Ford Dealer. Do not use abrasive cleansers on glass as they may cause scratches. The windshield or rear window is clean if beads do not form when you rinse it with water.
Page 188 Maintenance and care Do not spray with cold water to avoid cracking the engine block or other engine components. Never apply anything to the drive belt (including belt dressing). Cover the highlighted areas to prevent water damage when cleaning the engine. Never wash or rinse the engine while it is running;...
Page 189 Maintenance and care Cleaning seats equipped with side air bags Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Follow the directions that come with the cleaner. Do not saturate the seat cover with upholstery cleaner. Do not use chemical solvents or strong detergents when cleaning the seat mounted side air bag.
Page 190 Dry with a soft cloth. For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label.
Page 191: Capacities And Specifications
If a spark plug needs to be replaced, use only spark plugs with the same service part number suffix letter as shown on the engine decal. REFILL CAPACITIES Fluid Ford Part Name Application Brake fluid High Performance DOT 3 Motor Vehicle Brake...
Page 192 Windshield Washer Concentrate Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. Rear axle lubricants do not need to be checked or changed unless a leak is suspected, service is required or the axle assembly has been submerged in water.
Page 193: Lubricant Specifications
Capacities and specifications LUBRICANT SPECIFICATIONS Item Ford part name Brake fluid High Performance DOT 3 Motor Vehicle Brake Fluid Door Silicone Lubricant F7AZ-19G208-BA weatherstrips Door latch, hood Multi-Purpose latch, auxiliary Grease hood latch, door hinges, striker plates, seat tracks and fuel filler...
Page 194: Engine Data
Ford specification EST-M2C118-A for complete refill of Traction-Lok axles. Ford design rear axles contain a synthetic lubricant that does not require changing unless the axle has been submerged in water. Ensure the correct automatic transmission fluid is used.
Page 195 Capacities and specifications...
Page 196: Certification Label
Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block and transmission. MFD. BY FORD MOTOR CO. IN U.S.A. DATE: XXXXX GVWR:XXXXXXXXXXXX FRONT GAWR: XXXXXX/XXXXXXX REAR GAWR: XXXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL...
Page 197: Customer Assistance
There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage. (In Hawaii, rules vary. See your dealer for details.)
Page 198 Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could...
Page 199 Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Assistance Center: Your telephone number (home and business)
Page 200 In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be...
Page 201 What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance as designed concerns on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible...
Page 202 DSB’s independent administrator Your dealership and a Ford Motor Company representative will then be asked to submit statements. To properly review your case, the Board needs the...
Page 203 Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 204 UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 205 Customer assistance decisions are fast, fair, and final; the arbitrator’s award is binding both to you and Ford of Canada. CAMVAP services are available in all territories and provinces, except Quebec. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685.
Page 206 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY...
Page 207 Canada) * May be sold with the Motorcraft name FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs;...
Page 208 Customer assistance greater. See your dealer for complete warranty information and availability. Not all accessories are available for all models. Vehicle Security Styled wheel protector locks Vehicle security systems Comfort and convenience Ash Cup Cargo nets Cargo organizers Dash trim Electrochromic mirror with compass Electrochromic mirror with compass and temperature display...
Page 209 Cleaners, waxes and polishes Flat splash guards Front end covers (full and mini) Lubricants and oils Molded splash guards Molded vinyl floor mats Seat belt extenders Tonneau covers (mini) Touch-up paint Universal floor mats For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: When adding accessories, equipment, passengers...
Page 210 Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3.
Page 211: Reporting Safety Defects
National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 212: Index
Index Air bag supplemental restraint system ... 75,76 and child safety seats ... 77 description ... 76 disposal ... 80 driver air bag ... 78 indicator light ... 9,80 operation ... 78 passenger air bag ... 78 Air cleaner filter ... 191 Air conditioning ...
Page 213 ... 150,191 specifications .. 193,194 Cruise control (see Speed control) ... 42 Customer Assistance ... 116 Ford accessories for your vehicle ... 206 Ford Extended Service Plan ... 197 Getting assistance outside the U.S. and Canada ... 205 Getting roadside assistance ...
Page 214 Index Doors lubricant specifications ... 193 Driving under special conditions through water ... 115 Emergencies, roadside jump-starting ... 128 Emission control system ... 175 Engine ... 194 check engine/service engine soon light ... 9 cleaning ... 187 coolant ... 143 idle speed control ...
Page 215 GAWR (Gross Axle Weight Rating) ... 109 definition ... 109 driving with a heavy load ... 109 location ... 109 GVWR (Gross Vehicle Weight Rating) ... 109 calculating ... 109 definition ... 109 driving with a heavy load ... 109 location ...
Page 216 Index low fuel ... 11 overdrive off ... 11 safety belt ... 8 service engine soon .. 9 traction control active ... 12 turn signal indicator ... 8 Load limits ... 109 GAWR ... 109 GVWR ... 109 trailer towing ... 109 Locks doors ...
Page 217 warning light and chime ... 8,13,70 Safety seats for children ... 82,83 Seat belts (see Safety restraints) ... 65 Seats ... 62 child safety seats ... 82,83 cleaning ... 189,190 easy access/easyout feature ... 64 SecuriLock passive anti-theft system ... 57,58,59 Servicing your vehicle ...
Page 218 Index Windshield washer fluid and wipers checking and adding fluid ... 143 checking and cleaning ... 159 operation ... 40 replacing wiper blades ... 160 Wrecker towing ... 132...
Page 223: Filling Station Information
3.8L (4.0 quarts). Use Ultra-Clear fluid Windshield Washer Concentrate. Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. Ensure the correct automatic transmission fluid is used.
Page 224 Filling station information Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface. Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with in-tank cooler. The amount of transmission fluid and fluid level should be set by the indication on the dipstick’s normal operating range.

This manual is also suitable for:

Mustang gt 1999

Ford 2000 Mustang Owner's Manual

Quick Links

Related Manuals for Ford 2000 Mustang

Summary of Contents for Ford 2000 Mustang

This manual is also suitable for:

Table of Contents