Add/Remove Dvd/Cd Drive; Data Management Setting For Main Memory - Mitsubishi Electric DX-TL5000E Installer Manual

Memory (continued)

Add/Remove DVD/CD Drive

This item is used to set the DVD/CD drive device for the
DVD/CD group of the copy 1 or 2 device.
• You cannot set this item during recording or playback.
System Menu
5 Memory
Add/Remove DVD/CD Drive
2
1. Make sure that the DVD/CD drive connected is
step
displayed in the <Add/Remove DVD/CD Drive>.
• When you select "Eject," the access LED on the
device illuminates and the disc tray opens.
2. Select the desired copy device number (1 or 2) to
step
be set.
Copy1: Registers for the copy 1 device.
Copy2: Registers for the copy 2 device.
• The button changes in the order of "Copy1" and
"Copy2" each time you press the button.
• Only one DVD/CD drive can be used (including built-
in CD/DVD drive).

Data Management Setting for Main Memory

This item is used to set the operation of the unit when
space of the main device becomes full during recording.
And also used to set the partition of the main device.
• You cannot set this item during recording or playback.
System Menu
5 Memory
Data Management Setting for Main Memory
3
Change Partition Setting
4
(Main Device Settings)
1. Select the desired repeat recording setting for each
step
area.
Repeat On: Automatically returns to the beginning
of the HDD and resumes recording (by overwriting
the existing data).
Repeat Off: Stops recording and displays the
warning message on the screen. To resume
recording, clear the warning display and then press
the REC/STOP button. Note that recording stops
without displaying warning when the warning is not
set to display.
• "Repeat of Alarm Recording Area" can be set when "Alarm
Recording Area" (System Menu Memory Data
Management Setting for Main Memory Change Partition
Setting) is set to other than "0 %."
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
82
• "Repeat of LPA Recording Area" can be set when "Long
Pre-Alarm Area" (System Menu Memory Data
Management Setting for Main Memory Change
Partition Setting) is set to other than "0 %."
• The warning is displayed as "ALERT" on the screen.
The last 16 warnings are stored, however, the warning
occurred before that is reset and its display is cleared.
• In the long pre-alarm area, the data is not overwritten
chronologically.
• If the warning message of disk full appears while the
alarm recording area is set, recording for both areas
will stop.
• When "Repeat of Alarm Recording Area" (System
Menu Memory Data Management Setting for Main
Memory) is set to "Repeat Off" and all of the alarm
area is used up, the alarm recording stops. If an alarm
is input after that, recording is not performed though
the indicator flashes. Switch "Repeat of Alarm
Recording Area" to "Repeat On" or clear the data in
the alarm area to restart recording.
(Change Partition Setting)
2 Set the partition for the main device.
step
• Select the desired capacity for the alarm recording
area and long pre-alarm area.
• When the alarm recording area is set to other
than "0 %," the HDD of the main device is
partitioned so that the specified alarm recording
area is used as the independent capacity for the
alarm recording.
• See pages 54 and 55 for the detail of the
long pre-alarm recording.
• The normal recording area is referred to as "normal
area," and the alarm recording area (PARTITION
area) is referred to as "alarm area," and the long pre-
alarm area is referred to as "LPA."
• When total value of the normal, alarm, and LPA
reaches 100 %, the capacity is not increased.
• You cannot set "Normal Recording Area" to "0 %."
1
step
• Playback, search, information display, remain setting,
2
step
mode out setting, call out setting, and data clear
function are performed independently for "normal
area," "alarm area," and "long pre-alarm area."
• The normal area or the alarm area is selectable when
copying the recorded data.
• In the case that "Alarm CH" is set, and an alarm signal
is input during normal recording for the camera
number which is not set for normal recording, pre-
alarm recording may not be performed.
System Menu