Opening And Removing Door; Glass/Door Maintenance; Fuel Conversion - Lennox Hearth Products RAVELLE 42 Installation And Operation Instructions Manual

Glass Door
• Do not attempt to substitute the materials used
on these doors, or replace cracked or broken
glass.
• Handle this glass with extreme care! Glass is
susceptible to damage – Do not scratch or handle
roughly while reinstalling the glass door frame.
• The glass door(s) of this appliance must only be
replaced as a complete unit as provided by the
manufacturer. Do not attempt to replace broken,
cracked or chipped glass separately.
• Do not attempt to touch the front enclosure glass
with your hands while the appliance is in use.
• Do not use abrasive cleaners. Never clean the
glass when it is hot.
Do not operate the appliance with glass removed,
cracked or broken.
Ne pas utiliser l'appareil si le panneau frontal en
verre n'est pas en place, est craqué ou brisé.
Only doors certified with the appliance shall be used.
Seules des portes certifiées pour cet appareil doivent être
utilisées.
CAUTION: DO NOT abuse glass door by striking or slamming shut.
Do not remove glass door while the appliance is hot.

Opening and Removing Door

While holding the door against the firebox, pull each latch forward and
up - releasing the top of the glass door . To remove the door, grasp it
firmly with both hands and lift it up so the two tabs at the bottom of the
door are lifted out of their retaining slots . The glass door is quite heavy,
so it is important to place it in a secure spot until reinstalled . To reinstall
the door, the tabs at the bottom of the door must be inserted in the slots
at the bottom of the firebox . The spring loaded latches must be pulled
forward and down to apply pressure against the door .
Figure 49
38
WARNING
CAUTION
ATTENTION
Door Latch
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Glass/Door Maintenance

Cleaning: When cool, the glass may be cleaned with a clean, soft cloth
and a household glass cleaner . For cleaning white condensation from the
interior glass use a gas fireplace glass cleaner available from your fireplace
dealer . Use of caustic or abrasive cleaners may damage glass . Gold or
nickel plated doors must be cleaned with a household glass cleaner or
denatured alcohol and a soft cloth before firing or fingerprints and stains
will remain permanently . DO NOT spray commercial glass cleaner with
ammonia on the door and glass gasket as it may dissolve the gasket glue .
Repair:
If the glass is broken in the glass door, the entire door (metal
frame, gasket and glass) should be replaced as a unit . This replacement
glass door is available from your Lennox Hearth Products dealer . Do not
use substitute parts or materials . The glass is neo-ceramic and alterna-
tive types must not be used .
NOTE: BE CAREFUL NOT TO SPRAY COMMERCIAL GLASS
CLEANER WITH AMMONIA ON GASKET AREA OF DOOR. AM-
MONIA WILL DISSOLVE GASKET GLUE.
NOTE: GOLD PLATED SURFACE MUST BE CLEANED WITH GLASS
CLEANER AND SOFT RAG BEFORE FIRING THE FIRST TIME OR
FINGER PRINTS AND STAINS WILL REMAIN PERMANENTLY.
NEVER USE BRASS POLISH TO CLEAN GOLD, THIS WILL RE-
MOVE GOLD PLATING!

Fuel Conversion

Converting the Ravelle™ 42 gas fireplace between natural gas and LP can
be accomplished by either changing the cassette (valve and pilot assembly)
or installing a conversion kit (regulator, burner orifice and changing the
orifice position on the pilot) . Only a qualified service technician should
perform the conversion .
Cassette Removal:
1 . Be sure the gas supply is shut off and the fireplace electrical supply
is shut off at the electrical panel before beginning the conversion .
Disconnect the gas supply from the fireplace, being careful not to
apply pressure to the valve in the process .
2 . Remove the log set and brick panels (see Brick Panel and Log Set
Installation) .
3 . Remove the two allen head screws at the left and right rear of the
firebox securing the burner support . Lift out the burner and burner
support .
4 . Remove the two allen head screws holding the burner in place .
5 . Remove the labeled cover through which the valve control knobs
protrude by removing the two allen head screws securing it and slide
it off the valve knobs .
6 . Mark and disconnect wires on valve terminals #1 and #3 connected
to the burner on/off switch, thermostat, or remote control .
7 . Remove all the allen head screws (around the perimeter of the cassette
panel) fastening the cassette to the firebox .
8 . Grasp the cassette assembly from inside the firebox and pull it into
the firebox and out of the fireplace .
9 . Install new, converted, or serviced cassette in the reverse order of
removal . Replace gasket if necessary .
10 . All parts and wires must be correctly reinstalled to ensure safe and
proper operation of the unit .
Conversion Kit:
Please see instructions provided with conversion kit .