Operating Instructions; Pre-Lighting Checklist; Lighting Instructions - Lennox Hearth Products RAVELLE 42 Installation And Operation Instructions Manual

OPERATION

Operating Instructions

Pre-Lighting Checklist

Be sure to check these items before the initial lighting of the fireplace:
c T he fireplace gas label corresponds to the gas supply available
- that is "natural gas" for natural gas or "LP gas" for Propane
gas .
c G as pressure has been checked carefully - see Page 26 .
c A ll gas fittings have been checked for leaks .
c A ll clearances to combustibles have been met - see Page 10 .
c A ll combustible materials have been removed from the area in
front of the fireplace .
c A ll vented areas of the fireplace face are unobstructed .
c H ouse is ventilated to clear initial paint curing odors - see Page
35 .
c A ll packaging materials have been removed from the firebox .
c W hile fireplace is cool, fingerprints or other marks have been
cleaned from any gold or nickel surfaces with denatured alcohol
and a soft cloth . Marks left on these surfaces may become
etched into the finish if not removed prior to burning the unit .
c B rick panel, log set, volcanic stone and embers have been
installed .
c T he glass door is in place and is properly sealed .

Lighting Instructions

CAUTION: HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP
CHILDREN, FURNITURE, GASOLINE AND OTHER LIQUIDS WITH
FLAMMABLE VAPORS AWAY. NEVER OPERATE UNIT WITH GLASS
OFF OR ATTEMPT TO REMOVE THE GLASS WHILE HOT.
CAUTION: YOUR LENNOX HEARTH PRODUCTS GAS APPLIANCE
MUST ALWAYS BE OPERATED WITH GLASS IN PLACE.
The following is a copy of the operating and lighting instructions
found with each fireplace:
FOR YOUR SAFETY READ BEFORE OPERATING
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS
EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING
PROPERTY DAMAGE, INJURY, OR LOSS OF LIFE.
A . This appliance is equipped with a piezo ignition device to light the
pilot . When lighting the pilot, follow these instructions exactly .
B . BEFORE LIGHTING, smell around the appliance area for gas .
Be sure to smell next to the floor, because some gas is heavier
than air and will settle on the floor .
WHAT TO DO IF YOU SMELL GAS:
• DO NOT try to light the appliance .
• DO NOT touch any electric switch; do not use any phone in
your building .
• Immediately call your gas supplier from a neighbor's phone .
Follow the gas supplier's instructions .
• If you cannot reach your gas supplier, call the fire department .
C . Use only your hand to push in or turn the gas control knob .
Never use any tool . If the knob will not push in or turn by hand,
don't try to repair it, call a qualified service technician . Force or
attempted repair may result in a fire or explosion .
D . DO NOT use this appliance if any part has been under water .
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and any
gas control which has been under water .
LIGHTING INSTRUCTIONS
1 . STOP!! Read the safety information on this page before
proceeding.
2 . (If applicable) Set the thermostat to lowest setting . Turn wall
on/off switch, unit mounted on/off switch or remote control
switch "OFF ."
3 . Turn off ALL electrical power to the appliance .
4 . Open the lower door to access control compartment . Make
sure gas supply shut-off cocks are open .
5 . Push in gas cock dial slightly and turn clockwise
"OFF ."
.2 Note: Dial cannot be turned from "PILOT" to "OFF" unless dial
is pushed in slightly. Do not force.
6 . Wait five (5) minutes to clear out any gas . Then smell for gas,
including near the floor . If you smell gas, STOP! Follow "B"
on this page . If you don't smell gas, go to the next step .
7 . Locate the pilot by looking at the left center of the burner,
under the left elevated log . Blue flame will be seen when the
pilot is lit .
8 . Turn the gas control knob counterclockwise
"PILOT ."
9 . Push in control knob all the way and hold in . Immediately
light the pilot by triggering the piezo igniter (pushing the
button) until pilot lights . Continue to hold the control knob
in for about 1-1/2 minutes after the pilot is lit . Release knob
and it will pop back out . Pilot should remain lit . If it goes out,
repeat steps 5-9 .
• If knob does not pop up when released, stop and immediately
call your service technician or gas supplier .
• If the pilot will not stay lit after several tries, turn the gas
control knob to "OFF" and call your service technician or
gas supplier .
to
to
33