Troubleshooting - Korg Electribe SmkII Owner's Manual

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
8. Appendices
8. About system exclusive messages
Manufacturers are free to use system exclusive messages in any
way they choose, and these messages are used mainly to transmit
and receive parameters that are specific to particular devices, such
as sound data and editing data.
The system exclusive message format of the ES-1
3n, 57, ... F7] (n: exclusive channel).
However, some system exclusive messages have been defined for
use in a specific way, and these are called "universal system exclu-
sive messages."
Of the various types of universal system exclusive messages, the
ES-1 II supports the following two types.
mk
· When an Inquiry Message Request [F0, 7E, nn, 06, 01, F7] mes-
sage is received, the ES-1
[F0, 7E, nn, 06, 02, (9 bytes), F7] that means "I am a Korg ES-
1 II, and my system version is ..."
mk
· When a Master Volume [F0, 7F, nn, 04, vv, vv, 01, F7] is received,
the volume of the entire system will be adjusted.
9. Transmitting sound settings
and other data (Data Dump)
Song, Pattern, and Global data can be transmitted as MIDI exclu-
sive data, and stored on an external device. This data is transmit-
ted and received on the MIDI channel selected in Global mode.
Data dumps will be transmitted when a Data Dump Request of
the corresponding type is received.
10. Editing sounds etc.
By sending MIDI exclusive data dumps, you can rewrite all pat-
terns or individual programs. By using NRPN messages in Pat-
tern mode, you can edit the knobs that are active for each part.
58
II is [F0, 42,
mk
II will transmit an Inquiry Message
mk

Troubleshooting

The display does not light up when I press the Power switch!
• Is the AC adapter connected?
• Is the AC adapter plugged into an AC outlet?
No sound!
• Is your amp, mixer, or headphones connected to the correct
jack? (Can you playback a pattern? If so, the connections are
correct.)
• Are your amp or mixer powered-on and set correctly?
• Is the master volume knob of the ES-1
• Has the volume been lowered by a MIDI Master Volume mes-
sage?
Sound does not stop!
• When a pattern is played back, it will continue playing repeat-
edly. When you are finished listening to a pattern, press the
Stop/Cancel key (p.13, 14).
Sounds or operations are different than when I edited!
• Did you perform the Write operation after editing? (p.47, 52)
After you have edited, you must perform the Write operation
before switching songs or patterns, or turning off the power.
• Did you edit the selected pattern or song after writing it?
Can't control via MIDI!
• Is the MIDI cable connected correctly?
When playing the ES-1 II from an external device
mk
• Has the ES-1 II been set to receive MIDI data on the channel
mk
on which the data is being transmitted? (p.54)
• Is the MIDI mode MIDI Channel parameter set to the desired
channel? (p.54)
When playing an external device from the ES-1
• Does the MIDI channel of the ES-1
of the receiving device? (p.54)
Can't write a pattern or song!
• Is the Global mode Protect setting turned "on"? (p.56)
Striking a part key does not play the specified sound!
• After editing the sound of a part, did you perform the Write
operation? (p.47)
• Is a motion sequence operating? (p.41)
II raised?
mk
II
mk
II match the MIDI channel
mk