Synchronizing An External Midi Device To The Es-1Mkii As Master (Int); Midi Channel Settings (Midi Ch); Setting The Midi Note Number For Each Part (Note No.); Setting The Audio In Mode (Audio In Mode) - Korg Electribe SmkII Owner's Manual

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
7. Global mode
Synchronizing an external MIDI
device to the ES-1
(int)
1. Use a MIDI cable to connect the MIDI OUT connector of the
ES-1 II to the MIDI IN connector of the external MIDI device
mk
(sequencer or synthesizer etc.).
2. Use the cursor keys to make the parameter select LEDs indicate
CLOCK.
3. Rotate the dial to select "Int" (internal clock).
4. Make settings on the external MIDI device (slave) so that it will
receive MIDI Clock messages.
5. When you start playback on the ES-1
device will begin playback in synchronization.
When you perform the Reset & Play operation to begin play-
back from the beginning of the pattern, the ES-1
mit only a MIDI Start message.
MIDI cable
MIDI keyboard or
sequencer etc.
MIDI channel settings
(MIDI CH)
MIDI CH
This sets the MIDI channel. The same MIDI channel is used for
both transmission and reception.With the factory settings this will
be "11"
1. Use the cursor keys to make the parameter select LEDs indicate
MIDI CH.
2. Rotate the dial to select the channel.
Setting the MIDI note number
for each part (NOTE NO.)
In order to make this setting, you must enter Global mode
from Pattern or Song mode.
If you enter from Sample mode, the display will indicate "- - -"
and it will not be possible to change the setting.
NOTE NO.
Here you can specify the MIDI note number for each part.
If you specify the same note number for two or more parts, the
sounds of those parts will be played simultaneously when that
note is received from an external MIDI device.
1. Use the cursor keys to make the parameter select LEDs indicate
NOTE NO.
54
II as master
mk
II, the external MIDI
mk
mk
1
MIDI OUT
MIDI IN
2
2. Press the part key whose note number you wish to change (the
key will light).
3. Rotate the dial to select the note number.
The factory settings are as follows.
Part
Sample 1
Sample 2
Sample 3
Sample 4
Sample 5
Sample 6A
Sample 6B
Sample 7A
Sample 7B
Slice Sample
AUDIO IN
Note names will appear in the display as follows.
II will trans-
Display for A 2
The correspondence between note names and note num-
3
bers will differ by manufacturer. Please refer to the owner's
manual for the device you have connected.
Setting the audio in mode
(AUDIO IN MODE)
AUDIO IN MODE
This setting specifies whether the sound that is input from the
audio in jack will be handled as monaural (left channel only) or
stereo. When using a monaural source such as MIC input, select
1...16
"L." When using a stereo source such as a CD player, select "St.."
1. Use the cursor keys to make the parameter select LED indicate
AUDIO IN MODE.
2. Rotate the dial to select either "L" or "St.."
Even if the AUDIO IN MODE is set to stereo, a Sampling Mode
setting of monaural will cause the left and right channels to be
mixed and sampled in monaural.
If you set the AUDIO IN MODE to stereo, use a stereo phone plug
to make connections.
C-1...G9
Note name Note number
C2 36
D2 38
E2 40
F2 41
G2 43
C4 60
C 4 61
F 2 42
A 2 46
B2 47
A2 45
Display for B4 Display for D Ð1
L (monaural), St. (stereo)