Table of Contents
Advertisement
COPY OF LIGHTING PLATE INSTRUCTIONS
National Fuel Gas Code, ANSI Z223.1/NFPA 54, or Natural Gas and Propane Installation Codes,
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life. Improper
installation, adjustment, alteration, service or maintenance can cause injury
or property damage. Refer to the owner's information manual provided with
this appliance. For assistance or additional information consult a qualified
installer, service agency or gas supplier.
A) This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these
B) BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the fl oor
C) Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not
D) Do not use this appliance if any part has been under water. Immediately call a qualifi ed service
E) This appliance needs fresh air for safe operation and must be installed so there are provisions for
CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due
to high surface temperatures keep children, clothing and furniture, gasoline and
other liquids having fl ammable vapors away. Keep burner and control compartment
clean. See installation and operating instructions accompanying appliance.
1) Push in gas control knob slightly and turn clockwise
2) Wait fi ve (5) minutes to clear out any gas. If you then smell gas STOP! Follow step "B" in the Safety
3) Turn knob on gas control counterclockwise
4) Push in control knob all the way and hold in until the pilot lights up. Continue to hold the control
5) Turn gas control knob counterclock-wise to "ON".
6) Turn the unit on.
1) Turn off the unit.
2) Push in the gas control knob slightly and turn clockwise
3) Turn off all electric power to the appliance if service is to be performed.
Regency
®
L900 Direct Vent Gas Fireplace
FOR YOUR SAFETY READ BEFORE LIGHTING
This appliance must be installed in accordance with local codes, if any; if none, follow the
CSA B149.1. (Australia: AS5601-2004, New Zealand: NZS 5261)
instructions exactly.
because some gas is heavier than air and will settle on the fl oor.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electric switch, do not use any phone in your building.
- Immediately call your gas supplier from a neighbours phone. Follow the gas supplier's
instructions.
- If you cannot reach your gas supplier, call the fi re department.
push in or turn by hand, don't try to repair it, call a qualifi ed service technician. Forced or attempted
repair may result in a fi re or explosion.
technician to inspect the appliance and to replace any part of the control system and any gas
control which has been under water.
adequate combustion and ventilation air.
LIGHTING INSTRUCTIONS
STOP! Read the safety information above on this label.
"PILOT" to "OFF" unless knob is pushed in slightly. Do not force.
PILOT BURNER
VEILLEUSE
THERMOPILE
ELEMENT
THERMO-
ELECTRIQUE
Information above on this label. If you don't smell gas, go to the next step.
knob in for about 20 seconds after the pilot is lit. Release knob and it will pop back up. Pilot should
remain lit. If it goes out, repeat steps 1) to 4). If knob does not pop up when released, stop and
immediately call your service technician or gas supplier. If the pilot will not stay lit after several tries,
turn the gas control knob to "OFF" and call your service technician or gas supplier.
TO TURN OFF GAS APPLIANCE
You may shut off the pilot during prolonged non use periods to conserve fuel.
DO NOT REMOVE THIS INSTRUCTION PLATE
OPERATING INSTRUCTIONS
to "OFF". Knob cannot be turned from
OFF
to"PILOT".
to "OFF". Do not force.
918-583
41
Advertisement
Table of Contents
