Genie GPS-IC Series Owner's Manual page 18

3 3 3
S S AFE - - T T - - B B E E A A M M
...
18
If you have plugged in the po
—UNPLUG IT NOW.
N N N N O O T T T T E E E E : : : T T T T h h h h e e e e o o p p e e r r r a a a a t t o o r r r w w i i l l l l l l l n n o o t t c c l l o o o o s s s s e e t t t h h e e d d d o o o o o o o r r r r
a a utomatic c a l l l l y u u n n l l ess s the S S a a fe - - T-Be a a m
i i s in n s s ta l l l l ed d . .
1.
Mark both sides of garage door frame or wall 5
•
above floor (Fig. 3-1) .
Hold bracket against door frame or wall.
•
Check if brackets extend out from wall far
–
enough, so tongue of bracket is beyond door,
tracks or any door hardware.
If not:
–
a. STB bracket extensions are available at
local dealer.
b. Blocks of wood, etc. may be substituted
for extensions.
Center bracket on your mark (Fig. 3-2) .
•
Fasten each with 2 screws [ 127 ].
•
[ 127 ]
NOTE: Mounti i ng bra c c ket t s s c a a n be at t t t a a ched d t t o o t t h h e e
floor usi i ng c o o ncrete a a nchors (n n o o t t p p r r o o v v ided d ) ) . .
2. Mounting STB source and sensor .
If garage has only one garage door.
•
Determine which side of garage receives
–
most direct sunlight (Fig. 3-4) .
Red LED should always be on sunny side
–
whenever possible (Fig. 3-4) .
For multiple doors.
•
Preventing crossed signals is critical.
–
Place source and sensor modules on
–
adjacent doors facing in opposite directions
(Fig. 3-4) .
NOTE: : To o hel l p pre e ven n tin n ter r f f ere e ncefro o m sun, S S TB B
se n n s s or r s ( ( g g ree e n L E E D) ) may y b e e pla a ced f f u u r r ther r a w w ay y
from t t h h e d d o o o o r opening w w her r e t t h h e e y wil l l s s pen n d mo r r e e
tim m e i i n sh h ado o w w s. .
Slide source/sensor onto tongue of bracket
•
until it clicks into place (Fig. 3-3) .
OPEN RED PARTS BAG
3.
.
Route wire using either method shown (Fig. 3-5) .
•
Securely fasten wires to wall as you go.
•
Use insulated staples (included).
–
[ 128 ]
Staples should be snug only.
–
I I N N S S TA A L L LA A T T ION N
®
WARNING
e-T-Beam System
®
S S y y ste m m
®
kets .
#10-16 x 1-1/4
Insulated staple
FOR HE E LP P -1. . 80 0 0.354. . 36 6 43 OR R GEN N IECOM M PA A N N Y. . COM M
d
"
FIG. 3-2
"
RED
LED
ONE DOOR
GARAGE
GREEN
LED
THREE DOOR
GARAGE
Green
Source
A
FIG.
br ket
Attaching STB
(See directions on next page and
kets .
Figure 3-4 before attaching.)
SUN
GREEN GREEN RED RED
LED LED LED LED
TWO DOOR
GARAGE
RED RED GREEN GREEN
LED LED LED LED
FIG. 3-4 STB locations .
Dashed Line = striped wire
Solid Line = white wire
Green
Red
Source
Sensor
Power
Head B
FIG.
.
tongue
IG. 3-3
F
kets
'
GREEN
LED
RED
LED
Red
Sensor
Power
Head
.