Genie GPS-IC Series Owner's Manual page 10

Automatic chain drive/belt drive garage door operator system
Hide thumbs Also See for GPS-IC Series:
Table of Contents

Advertisement

1 1
O O O P P E E R R R R A A A A T T T O O O R R A A A A S S S S S S E E M M M M B B L L Y Y Y
. . . . . . . . . . .
OPEN BLUE PARTS BAG
Screws for attaching light cover are included in this
bag. Please set aside for use later.
10
1. Attach emergency release knob cord (Fig. 1-1).
Tie overhand knot in end of cord.
Thread cord through knob so knot is inside knob.
Thread cord through hole in carriage lever.
Tie overhand knot in other end of cord.
Do Not cut cord until after power head is mounted.
2. Attach emergency release tag (Fig. 1-1).
Thread wire through hole in carriage lever.
Wrap wire around itself, tie securely.
PLEASE NOTE THE ASSEMBLY PROCEDURES
ARE DIFFERENT FOR RAIL AND CHANNEL. BE
SURE TO FOLLOW THE APPLICABLE STEPS.
C C C C H H A A N N N N N N E E E E L L & & & P P P P O O O O W W W W E E R R R H H H H E E A A D D A A S S S S S S S S E E E M M B B L L L L Y Y Y
Do Not attempt to run power head or to set limits until
operator is fully assembled and attached to the door.
3. Place power head and channel on clean,flat surface.
4. Slide drive end of channel down over
power head (Fig.1-2).
Support header end of channel level with power head.
Slide carriage to align
Slide channel down
5. Fasten channel to power head .
Align mounting holes in front and rear of power head frame.
Insert and securely tighten the four (4) No.10 x 1/2
head screws [ 69 ] .
NO O T T E E : : C C hain i i n n n n e r r -s s lide e o o r b b e e l l t t bu u lle t t s s ho o u u ld r r em m a a in n at
mid- - tra a vel when a a s s sembling g to power h h e e a a d to provide e p p rope e r
t r r ave e l wh h en n se t t ti i n n g l l i i m m i i t t s.
R R AIL & & P P O O WE E R R H H E E A A D ASSEMBLY
Do Not attempt to run power head or to set limits until
operator is fully assembled and attached to the door.
3. Place power head and rail on clean, flat surface.
4. Slide drive end of rail down over
of power head (Fig. 1-3).
Support header end of rail level with power head.
Slide carriage enough to align
in sprocket.
Slide rail down
drags on the rail
CAUTION
D
-shaft on top of
"
"
D
-shaft with
D
-hole in sprocket.
"
"
"
"
D
-shaft flush with power head.
"
"
CAUTION
D
-shaft on top
"
"
D
-shaft with
"
"
D
-shaft flush with power head.
"
"
F F O O R HELP- - 1.800. . 35 5 4.364 4 3 3 O O R GENIE E CO O MPANY.CO O M
Toward Door
Carriage
Emergency
Release
Tag
Emergency
Release
Cord
[ 69 ]
Hex Head Screws
hex
"
[ 112 ]
5/16
"
Carriage Stop
D
-hole
"
"
[ 112 ]
Toward Power Head
Emergency
Release
Knob
Fig. 1-1
D
-Shaft and Hole
"
"
Fig. 1-2
[ 69 ]
No. 10 x 1/2
Hex Head Screw
"
[ 69 ]
No. 10-24 x 1/2
x 1/2
Hex Head Screws
"
Sprocket Saddle
"
Fig. 1-3
5/16
x 1/2
Hex Head Washer Screw
"
"
Hex Head Screws
"
D
-Shaft and Hole
"

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Pmx-ic b series

Table of Contents