Table of Contents
Advertisement
5. Fasten rail to power head.
Align mounting holes of sprocket saddle, rail
•
and power head frame.
• Insert the two (2) 5/16
screws[112], then two (2) No. 10-24 x 1/2
head screws [69].
Tighten screws.
•
N N O O TE: Inner r - - s s lid d e e /bull l et sh h o o u u l l d remai i n a t t m i i d d - - t t r r a a vel
w w hen n a a sse e mbli i ng to power r h h e e ad d t t o p p r r o o v v ide p p r r o o p p e e r
t t r r a a v e e l wh h e e n set t t t i i ng limi i ts s .
6. Use adjusting bolt to set chain tension (Fig. 1-4)
Chain should sag slightly but not so much that it
•
drags on the rail.
OPEN ORANGE PARTS BAG
2 2
I I NST T ALLA A T T IO N N
...
IMPORTANT
INSTALLATION
INSTRUCTIONS
W W W W A A A A R R R N N N I I I N N G G G G
Toreduce the risk of
severe injury or death:
1. READ AND FOLLOW ALL SAFETY, INSTALLATION AND
OPERATION INSTRUCTIONS. If you have any questions or
do not understand an instruction, call your service
representative.
2. Do Not install operator on an improperly balanced door. An
improperly balanced door could cause severe injury. Repairs
and adjustments to cables, spring assembly, and other
hardware must be made by a trained service person using
proper tools and instructions.
3. Remove all ropes and disable all locks connected to the
door before installing operator.
4. Install door operator 7 feet or more above the floor. Mount
the emergency release knob 6 feet above the floor.
5. Do Not connect the operator to the source of power until
instructed to do so.
6. Locate the control button:
• Within sight of door.
• At a minimum height of 5 feet, so small children cannot
reach it.
• Away from all moving parts of the door.
7. Install the entrapment WARNING label next to the wall
button or console. Install the emergency release tag on, or
next to, the emergency release.
8. The operator must reverse when the door contacts a 1-1/2
inch high object on the floor at the center of the doorway.
This is about the size of a 2" x 4" board laid flat.
x 1/2
hex head
"
"
hex
"
: : : :
Adjusting
Bolt
Fig. 1-4
FOR H H E E L L P P -1. . 80 0 0.354. . 36 6 43 OR G G ENIECOM M PA A NY.COM M
W W H H A A A A T T T T T Y Y Y P P P P E E O O O F F D D O O O O O O R R D D D D O O Y Y O O O O U U H H A A V V V E E ? ?
L L o o o o o o k k a a t t t t t t h h e e d d r r r r a a a w w w w i i i n n n n g g s s b b e e e e l l l l o o o w w . . T T h h e e e e y y y t t t t e e l l l l l l l y y y y o o o o u u w w h h h e e e r r r r e e
t t o o o f f i i n n d d d d t t h h e e e i i n n n n s s t t a a l l l l a a t t i i o o n n n n i i n n s s t t r r r r u u u u c c t t i i o o n n n n s s y y o o u u n n e e e e d d
Track Guided Doors
SEE SECTION 2A
Section Door With
Curved Track Hardware
Curved
Track
with
Vertical
Section
H
"
"
DOTTED LINE AT
INDICATES HIGHEST
POINT OF TRAVEL
Trackless Doors
SEE SECTION 2 B.
1-Piece Door
Jamb Type Hardware
(No Track)
H
"
"
1-Piece Door With
Horizontal Track Hardware
Straight Track
(Horizontal Only)
H
"
"
H
"
"
1-Piece Door
Pivot Type Hardware
(No Track)
H
"
"
11
Hide quick links:
Advertisement
Table of Contents
