Table of Contents
Advertisement
Models:
QFI30
QFI35
• Important operating
a n d m a i n t e n a n c e
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppli-
er's instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer's instructions
and the manufactured home construction and safety standard,
Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
R
NOTICE
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11
Owner's Manual
• Leave this manual with
party responsible for use
and operation.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fi replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other fl ammable
materials.
• Keep clothing, furniture, draperies and other fl ammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fi tter.
A CO detector shall be installed in the room where the appliance
in installed.
Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.
Installation and Operation
1
Advertisement
Table of Contents
Related Manuals for Quadra-Fire QF130
Summary of Contents for Quadra-Fire QF130
-
Page 1: What To Do If You Smell Gas
Technologies suggests NFI certifi ed or factory trained This appliance is only for use with the type(s) of gas indicated professionals, or technicians supervised by an NFI on the rating plate. certifi ed professional. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 2: Congratulations
Your new Quadra-Fire gas fi replace will give you years of As the owner of a new fi replace, you’ll want to read and durable use and trouble-free enjoyment. Welcome to the carefully follow all of the instructions contained in this Quadra-Fire family of fi... -
Page 3: Table Of Contents
B. Flue Damper........20 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 4: Limited Lifetime Warranty
B. Limited Lifetime Warranty Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... - Page 5 B. Limited Lifetime Warranty (continued) Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11...
-
Page 6: Listing And Code Approvals
(0-2000 FT) QFI35 (NG) CANADA 33,250 18,250 (2000-4500 FT) 31,000 15,500 (0-2000 FT) QFI30 (LP) CANADA 27,500 14,500 (2000-4500 FT) 35,000 17,000 (0-2000 FT) QFI35 (LP) CANADA 31,000 15,500 (2000-4500 FT) Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 7: User Guide
SOLID FUEL FIREPLACE DECORATIVE DOORS (NOT SHOWN) SECTION 2.D. FIXED GLASS ASSEMBLY MANTEL (NOT SHOWN) SECTION SECTION 12.H. 5.B AND 11.A HEARTH CLEAR SPACE SECTION 2.C. Figure 2.1 General Operating Parts Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 8: Clear Space
Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one. For more information refer to the instructions supplied with your decorative door or front. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 9: Control Module Operation
fi replace with fi xed glass assembly removed. ™ • An Intellifi re Plus ignition system is standard with this appliance. SELECTOR SWITCH STATUS INDICATOR LED FLAME HI/LO SWITCH NG/LP SETTING Figure 2.3 Control Module Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 10: Lighting Instructions (Ipi)
See installation and operating vice agency or the gas supplier. instructions accompanying appliance. For additional information on operating your Hearth & Home Technologies fi replace, please refer to www.fi replaces.com. Final inspection by Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 11: After Appliance Is Lit
In an intermittent pilot ignition system (IPI), the pilot fl ame should turn off when appliance is Is it normal to see the pilot fl ame burn turned off. Some optional control systems available with IPI models may allow pilot fl ame to continually? remain lit. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 12: Maintenance And Service
• Carefully set fi xed glass assembly in place on appliance. Hold glass in place with one hand and secure glass latches with the other hand. • Reinstall door or decorative front. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 13: Maintenance Tasks-Service Technician
• Inspect for paint condition, warped surfaces, corrosion or perforation. Sand and repaint as necessary. • Replace appliance if fi rebox has been perforated. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 14: Burner Ignition And Operation
• Verify that there is not a short in fl ame sense circuit by checking continuity between pilot hood and fl ame sense rod. Replace pilot as necessary. (IPI only) Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 15: Installer Guide
SECTION 5.B AND 11.A SURROUND OR FRONT NOT SHOWN SECTION 2.D AND 8.D. HEARTH EXTENSION GAS LINE (SECTION 9) ACCESS THROUGH EXISTING MASONRY OR WOODBURNING FIREPLACE Figure 4.1 Typical System Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 16: Design And Installation Considerations
Noncorrosive leak check solution 1/2 - 3/4 inch length, #6 or #8 Self-drilling screws Caulking material (300º F minimum continuous exposure rating) Stove cement (1200ºF or higher continuous exposure rating) Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 17: Fireplace Size Requirements
**Unit depth is measured to the back of the surround to give the depth needed for installation. In addition to these dimensions, also reference Clearances and Mantel Projections (Section 5.B). Figure 5.1 Fireplace Opening Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 18: Mantel And Wall Projections
fi rebox. Combustible facings must not extend behind the insert surround. For non-combustible material specifi cations refer to section 1.E. Figure 5.3 Mantel Clearances Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 19: Termination Locations
Over 16/12 to 18/12 ..........7.0 Over 18/12 to 20/12 ..........7.5 Over 20/12 to 21/12 ..........8.0 * 3 foot minimum in snow regions Figure 6.1 Minimum Height From Roof To Lowest Discharge Opening Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 20: Installation Preparation
• It is recommended that extra length of gas line be installed within the existing wood burner or masonry fi replace to allow removal of the insert for future servicing needs. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 21: Installing Vent Pipe And Appliance
VENT PIPE INLET AIR STARTING COLLAR NOTE: TO ACHIEVE OPTIMUM PERFOR- MANCE OF INSERT, MINIMIZE OR AVOID BENDS IN EXHAUST VENT PIPE. STARTING COLLAR BRACKET EXHAUST STARTING COLLAR Figure 8.1 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 22: Placing, Securing And Leveling The Appliance
Figure 8.3 Location of AUX300 for Remote Control • Push insert into the opening so that it tightly overlaps Blower Function - IPI the fi replace opening. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 23: Installing Adaptor And Termination Cap
Remove 18 inch x 18 inch fl ashing on cap by removing 3 VENT PIPE VENT PIPE screws. Connect both the LINK-ZC-ADPB to Class A Pipe and the termination cap to the LINK-ZC-ADPB with the Figure 8.6 self tapping screws provided. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 24: Gas Information
1/2 inch (13 mm) T-handle manual shut-off valve and fl exible gas connector are connected to the 1/2 inch (13 mm) control valve inlet. • If substituting for these components, please consult local codes for compliance. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 25: Electrical Information
FLAME TO CORD AUX1 AUX2 MODULATION ASSEMBLY (110V) BATTERY PACK 6V DC ORANGE GREEN ROCKER (PILOT) SWITCH (MAIN) BROWN WALL SWITCH OR REMOTE INSTALL GROUND Figure 10.1 IPI Wiring Diagram Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 26: Optional Accessories Requirements
GRN (2) BLK (2) TO VALVE BRACKET (GROUND) PLUG INTO 120V EXISTING OUTLET DC REGULATOR RECEPTACLE VARIABLE SPEED CONTROL BLOWERS BLOWER TEMPERATURE RECEPTACLE SENSOR SWITCH Figure 10.2 Fan Wiring Diagram Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 27: Fan Wiring With Remote
SYSTEM IS CONTROLLED WITH RC200/RC300 REMOTE. PLUG INTO 120V EXISTING OUTLET DC REGULATOR RECEPTICLE BLOWERS AUX 300 MODULE TO CONTROL MODULE BLOWER RECEPTICLE Figure 10.3 Wiring Diagram - Fan with RC200/RC300 Remote Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 28: Finishing
fi rebox. Combustible facings must not extend behind the insert surround. For non-combustible material specifi cations refer to section 1.E. Figure 11.1 Clearances to Mantels or other Combustibles above Appliance Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 29: Appliance Setup
• Place lava rock in front of and to the sides of the burner. Figure 12.2 Placement of Embers PLACE LAVA ROCK IN SHADED AREA ONLY Figure 12.1 Placement of Lava Rock Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 30: Install The Log Assembly
Figure 4. Bend the refractory tab down as shown in Figure 5. Repeat this step for the right refractory panel. Figure 5. Bend Refractory Tab Figure 4. Install Side Refractory Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... - Page 31 Rotate the back end of the log clockwise until it contacts the right refractory panel. LOG GROOVE LOG PIN (FOR LOG #6) MATES WITH SLOT MATE NOTCH NOTCH WITH GRATE BAR Figure 10. Log #4 Figure 11. Log #4 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11...
- Page 32 Log #6 (SRV2227-704): Rest the left end of Log #6 on the burner. Mate the notch on the left end of log with the grate bar. The log should rest on both log grooves as illustrated in Figure 9 and Figure 10. 2227-935 Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11...
- Page 33 Install the left side refractory as shown in Figure 3. Bend the refractory tab down as shown in Figure 4. Repeat this step for the right refractory panel. REFRACTORY Figure 3. Install Side Refractory Figure 4. Bend Refractory Tab Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11...
- Page 34 Log #4 SRV(2225-705): Mate the slot on the bottom of Log #4 with the right log pin. Refer to Figure 11 for location of log slot. Rotate the right end of the log clockwise until the groove on the end of the log mates with the grate bar. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11...
- Page 35 Log #7 SRV2225-704): Note the location of the groove on the underside of the log. Place the opposite end on the fl at spot on Log #3. See Figure 9. Mate the groove on the underside of the log with the grate bar as shown in Figure 15, centered between the andirons. 2225-935B Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11...
-
Page 36: Fixed Glass Assembly
Verify top latches are fully engaged and then fasten the two bottom latches. QFI30 5/16 in. 1/2 in. QFI35 1/4 in. 1/2 in. Figure 12.3 Fixed Glass Assembly Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 37: Troubleshooting
D. Pilot valve solenoid Verify that 1.5 to 1.8 VDC is supplied to pilot solenoid from module. If below 1.5 volts, replace module. If 1.5 volts or greater, replace valve. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... - Page 38 fl ame sensing rod. Verify continuity with a multi-meter with ohms set at lowest range. Replace pilot if any damage is detected. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11...
-
Page 39: Reference Materials
4-13/16 4-7/16 1-3/4 1-3/4 10-1/2 9-1/2 *Note: Location G on Figure 14.1 is measuring the appliance depth, for installation depth reference Location G on Figure 5.1. Figure 14.1 Appliance Dimensions Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 40: Vent Kits Components
GK to connect collinear fl ex vent to SL-D vent pipe to extend the run. FLEX3-30: One 3 inch fl exible liner expands to 30 feet. FLEX-CNCT: Connector kit - 3 inch liner to 3 inch liner, one connector per kit. Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11... -
Page 41: Contact Information
Quadra-Fire, a brand of Hearth & Home Technologies Inc. 7571 215 Street West, Lakeville, MN 55044 www.quadrafi re.com Please contact your Quadra-Fire dealer with any questions or concerns. For the location of your nearest Quadra-Fire dealer, please visit www. .com.