Garland XG24-JIB Installation And Operation Manual

Garland XG24-JIB Installation And Operation Manual

Jack in the box gas xpress grills
Hide thumbs Also See for XG24-JIB:
Table of Contents

Advertisement

Quick Links

INSTALLATION &
OPERATING MANUAL
JACK IN THE BOX
GAS XPRESS GRILLS,
MODELS XG24-JIB, XG36-JIB

FOR YOUR SAFETY:

DO NOT STORE OR USE GASOLINE
OR OTHER FLAMMABLE VAPORS OR
LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER
APPLIANCE
WARNING:
IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR MAINTENANCE CAN
CAUSE PROPERTY DAMAGE, INJURY, OR DEATH.
READ THE INSTALLATION,
OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY
BEFORE INSTALLING OR
SERVICING THIS EQUIPMENT
Users are cautioned that maintenance and repairs must be performed by a Garland authorized service agent
using genuine Garland replacement parts. Garland will have no obligation with respect to any product that has been
improperly installed, adjusted, operated or not maintained in accordance with national and local codes or installation
instructions provided with the product, or any product that has its serial number defaced, obliterated or removed,
or which has been modified or repaired using unauthorized parts or by unauthorized service agents.
For a list of authorized service agents, please refer to the Garland web site at http://www.garland-group.com.
The information contained herein, (including design and parts specifications), may be superseded and is subject
to change without notice.
GARLAND COMMERCIAL INDUSTRIES
185 East South Street
Freeland, Pennsylvania 18224
Phone: (570) 636-1000
Fax: (570) 636-3903
Part # 4523133 Rev 4 (08/04/09)
Part # 4523133 Rev 4 (08/04/09)
PLEASE READ ALL SECTIONS OF THIS MANUAL AND
RETAIN FOR FUTURE REFERENCE.
THIS PRODUCT HAS BEEN CERTIFIED AS COMMERCIAL
COOKING EQUIPMENT AND MUST BE INSTALLED BY
PROFESSIONAL PERSONNEL AS SPECIFIED.
IN THE COMMONWEALTH OF MASSACHUSETTS
THIS PRODUCT MUST BE INSTALLED BY A LICENSED
PLUMBER OR GAS FITTER.
For Your Safety:
Post in a prominent location, instructions to be
followed in the event the user smells gas. This
information shall be obtained by consulting your local
gas supplier.
GARLAND COMMERCIAL RANGES, LTD.
1177 Kamato Road, Mississauga, Ontario L4W 1X4
CANADA
Phone: 905-624-0260
Fax: 905-624-5669
© 2007 Garland Commercial Industries, Inc.
Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XG24-JIB and is the answer not in the manual?

Questions and answers

Summary of Contents for Garland XG24-JIB

  • Page 1: For Your Safety

    Users are cautioned that maintenance and repairs must be performed by a Garland authorized service agent using genuine Garland replacement parts. Garland will have no obligation with respect to any product that has been improperly installed, adjusted, operated or not maintained in accordance with national and local codes or installation instructions provided with the product, or any product that has its serial number defaced, obliterated or removed, or which has been modified or repaired using unauthorized parts or by unauthorized service agents.
  • Page 2: Important Information

    IMPORTANT INFORMATION WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth de- fects or other reproductive harm. Installation and servicing of this product could expose you to air- borne particles of glass wool/ceramic fibers. Inhalation of airborne particles of glass wool/ceramic fibers is known to the State of California to cause cancer.
  • Page 3: Product Information

    PRODUCT INFORMATION The Garland Xpress Grill provides a method for efficient two-sided cooking, while accommodating a variety of products. The unit will also serve as a flat grill, and meets all standards for safety, efficiency, and cleanliness. Standard Features: • Stainless steel front, top & sides • 33,000 BTU/Hr input for each twelve-inch section of...
  • Page 4: Table Of Contents

    DIMENSIONS AND SPECIFICATIONS, MODEL XG24-JIB . . . . . . . . . . . . . . . . . .
  • Page 5 To View the Garland Part Number: ........
  • Page 6: Dimensions And Specifications, Model Xg24-Jib

    19.4 (1207mm) (813mm) (152mm) (76mm) Shipping: Weight 575Lbs/ 234Kg, 45 Cubic Feet TOP HEATER Garland products are not approved or authorized for home or 11 1/2" TOP VIEW residential use, but are intended for commercial applications 1 3/4" [292mm] [44mm] only.
  • Page 7: Dimensions And Specifications, Model Xg36-Jib

    (76mm) Shipping: Weight 965Lbs/ 438Kg, 59 Cubic Feet TOP HEATER 11 1/2" 1 3/4" Garland products are not approved or authorized for TOP VIEW [292mm] [44mm] home or residential use, but are intended for commercial applications only. Garland will not provide service,...
  • Page 8: Plug Configuration

    21.61 4-10AWG INTRODUCTION The Garland Xpress grill, for Jack in the Box provides The Garland Group agrees to repair or replace, at it’s a method for efficient two-sided cooking, while option, any part that proves to be defective in material or accommodating a variety of products.
  • Page 9: Shipping Damage Claim Procedure

    Shipping Damage Claim Procedure 2. Be sure to note, "visible loss or damage," on the freight bill or express receipt and have the person making the Please note that the Garland equipment was carefully delivery sign it. inspected and packed by skilled personnel before leaving 3. Concealed loss or damage: if damage is unnoticed until the factory.
  • Page 10: Installation

    INSTALLATION Rating Plate Location NOTE: When checking gas pressure, be sure that all other equipment on the same gas line is on. IMPORTANT: Rating plates for this appliance are located in The appliance and its individual shut-off valve must be two places: 1) inside back panel on left side, 2) under front disconnected from the gas supply piping system during any control panel on center. pressure testing of that system pressures in excess of ½ PSIG General Information (3.45kPa, 14”...
  • Page 11: Accessory Kit - Main Gas Inlet

    INSTALLATION continued Check the data plate to determine the proper type of gas Installation of Kit: before connecting the quick disconnect or piping from the A. Install the elbow on the end of manifold (3/4” NPT) building gas supply. underneath the griddle, tighten and align with the elbow An incoming gas pressure test nipple is provided on the facing the back of the unit.
  • Page 12: Accessory Kit - Electrical Supply Lines

    INSTALLATION continued Photo C Accessory Kit – Electrical Supply Lines: The accessory kit also contains electric power cord and plug and has a stain relief suited for each unit. See Plug Photo E Configuration in SPECIFICATIONS and Photo D Installation of Cord And Plug With Strain Relief: 4.
  • Page 13: Electrical Connection Terminal Block Connection

    INSTALLATION continued Grease Bucket: The griddle is supplied with two stainless steel side grease buckets that must be installed before the unit is used. Each bucket slides into position along stainless steel supports. Appliances Equipped with Casters: 1. The installation shall be made with a connector that complies with the Standard for Connectors for Moveable Gas Appliances, ANSI Z21.69 or latest edition, addenda Z21.69a-1989, and a quick-disconnect device that...
  • Page 14: Grill Controls

    GRILL CONTROLS WHEN PUSHED SIMULTANEOUSLY: "START COOK TIME COUNTDOWN" (flat grill cooking) OR "LOWER PLATEN" (two-sided cooking) DISPLAY INDICATORS CANCEL/ RAISE PLATEN BUTTON PRODUCT BUTTONS POWER ENTER MASTER BUTTON BUTTON POWER PROGRAM DOWN ARROW SWITCH BUTTON BUTTON TEMPERATURE UP ARROW BUTTON BUTTON Product Buttons (0-9):...
  • Page 15: Temperature Button

    GRILL CONTROLS continued Temperature Button: Enter Button: In the Cook mode, each time the button is pressed the Function is to accept programming steps. current temperature for one zone is displayed. The grill Cancel/Raise Platen Button, (Green): temperature is displayed first followed by the platen temperature.
  • Page 16: Operation

    OPERATION Installing Release Material: Thread the front edge of the release material sheet behind the release material bar on the front of the platen, then A release material sheet must be replaced when: around the top and down over the front of the bar as shown. • Product sticks to release material. Place locking clips over release material sheet and press into place over release material bar.
  • Page 17: To Cook In Two-Sided Mode

    OPERATION continued If ignition of the burner does not occur on the first trial, the The display alternately blinks the recipe and the word bottom indicator light will flash amber. If the burner(s) do SELECTED 2 times then the recipe will be displayed not light within four trials for ignition, the control will display continuously.
  • Page 18: Exit Standby Mode

    OPERATION continued 2. Press the GREEN (‘CANCEL/RAISE’) and the BLACK buttons 5. Press the ENTER key again, the heater’s control for the at the same time. As soon as the upper platen moves platen and grill are turned off and the display shows the down, the display will read “STANDBY MODE.
  • Page 19: Cleaning And Maintenance

    CLEANING AND MAINTENANCE Cleaning During Operation: 8. Scrape only the lower grill surface with a grill scraper, and squeegee any residue into the grease troughs with a grill 1. After each product load is removed, Use a grill scraper to squeegee.
  • Page 20: Platen Zeroing

    CLEANING AND MAINTENANCE continued 18. Rinse the lower grill by flooding the surface twice with 20. When cleaning is completed, you may turn the “MASTER lukewarm water. Squeegee after each rinse. POWER” (rocker) switch off. 19. Wipe the lower grill surface, backsplash, bullnose, and AFTER CLEANING, apply a thin coat of fresh shortening hood with a clean, damp cloth.
  • Page 21 PLATEN ZEROING continued Insert gap tool directly below platen adjusters. Part # 4523133 Rev 4 (08/04/09) Page 21...
  • Page 22 PLATEN ZEROING continued Platen Gapping Tool (PN 1838701) “No-Go” “Go” Platen leveling should be done from one corner to the opposite corner. The adjuster nuts should be turned opposite of one another. Platen Adjusting Tool (PN 4523323) This end to remove Adjuster Locking Cap This end to remove Grease Cap and to make adjustments to the...
  • Page 23: Optional Accessories

    OPTIONAL ACCESSORIES Teflon Sheet - 1799302 Teflon Clip - 1851303 Grill Squeegee - 1868201 Teflon Tool - 4525560 Part # 4523133 Rev 4 (08/04/09) Page 23...
  • Page 24: Programming

    PROGRAMMING Programming Modes/Menu Sequence: System Information System Information Page 24 Part # 4523133 Rev 4 (08/04/09)
  • Page 25 PROGRAMMING continued System Set-up System Set-up Service Mode Service Mode Part # 4523133 Rev 4 (08/04/09) Page 25...
  • Page 26: Menu Items

    PROGRAMMING continued Menu Items... 5. Use to choose the desired Menu Item. To Change the Cook Time of a Product: 6 Press three, (3) times to display “(MENU ITEM) UPPER TEMP XXX” displayed in °F or °C. 1. Press and hold for three, (3) seconds.
  • Page 27: To Change Product Button, "Key" Assignment

    SYSTEM INFO. ” 9. Press to exit. 5. Press three, (3), times to view the Garland Part Number System Info... for the grill. “GARLAND PART # X…X” is displayed. (number varies by grill). To View Recovery Time - Upper Platen: 6.
  • Page 28: To View The Flash Number

    PROGRAMMING continued To View the Flash Number: 5. Press six, (6), times to view the Download Number. “DOWNLOAD NUMBER X…X” is displayed. (Download 1. Press and hold for three, (3) seconds. “ENTER CODE” is number varies by grill). displayed. 6. Press to return to “PROGRAMMING MODE SYSTEM 2.
  • Page 29: To Change The Alarm Volume

    PROGRAMMING continued To Change Probe Calibration - Upper: 8. Press to return to “PROGRAMMING MODE SYSTEM SETUP” 1. Press and hold for three, (3) seconds. “ENTER CODE” is displayed. 9. Press again to exit. To Change the Alarm Volume: 2. Using the Product buttons, 0-9 enter the code, (1251). “ENTER CODE **** ”...
  • Page 30: To Change Platen Set

    PROGRAMMING continued • Temperature is currently falling from a detected peak 8. Press to return to “PROGRAMMING MODE MENU of 360°F or higher. ITEMS” • Temperature is falling and has fallen 2°F from a detected peak that is within the 350-360°F range. (i.e. 9. Press again to exit. calibration would be allowed at 355°F if the achieved To Change Control Type: peak temperature was 357°F) • Temperature is rising through the 350-360°F range as a Note: this must be verified if the control is changed, match result of a heat on pulse of less than 30 seconds.
  • Page 31: To Change The Grill Function

    PROGRAMMING continued 9. Press again to exit. 11. Press again to exit. To Change the Grill Function: To Change the Alarm Mode: 1. Press and hold for three, (3) seconds. “ENTER CODE” is 1. Press and hold for three, (3) seconds. “ENTER CODE” is displayed.
  • Page 32: To Modify A Product Name In Library

    PROGRAMMING continued 2. Using the Product buttons, 0-9 enter the code, (1251). 12. Press to exit. “ENTER CODE **** ” is displayed. Service Mode 3. Press to enter the Programming Mode. To Change SCK Address: “PROGRAMMING MODE MENU ITEMS” is displayed. 1.
  • Page 33: Calibration

    CALIBRATION Bi-Weekly Calibration: 3. Press and hold for three, (3) seconds. “ENTER CODE” is displayed. Tools: Digital Pyrometer with Surface Probe 4. Using the Product buttons, 0-9 enter the code, (1251). Warning: PERSONAL INJURY FROM BURNS MAY RESULT “ENTER CODE **** ” is displayed. WHEN COMING IN CONTACT WITH HOT COOKING SURFACES. 5.
  • Page 34: Probe Locations

    5.75" 5.75" 5.75" 22.5" 22.5" 11.25" 11.25" PLATEN PLATEN (2 PLACES) (3 PLACES) GRILL PLATE GRILL PLATE 24" 24" 12" 12" 6.09" 6.09" 6.09" 6.09" 18" 24" 36" MODEL XG24-JIB MODEL XG36-JIB Page 34 Part # 4523133 Rev 4 (08/04/09)
  • Page 35: Troubleshooting

    MAINTENANCE AND REPAIRS SHOULD BE PERFORMED BY Press to reset the message and silence the beep. YOUR LOCAL GARLAND AUTHORIZED SERVICE AGENCY. MOTOR OVER CURRENT: PROBE ERROR: ...displayed when the platen has been mechanically resisted..occurs when the probe is open or not connected. The The platen will stop and move to the lower limit.
  • Page 36: Wiring Diagrams

    WIRING DIAGRAMS ACTUATOR 1333W MOTOR YELLOW GRIDDLE GRIDDLE YELL PLATEN PLATEN 120V 240V SWITCH MAIN Page 36 Part # 4523133 Rev 4 (08/04/09)
  • Page 37 WIRING DIAGRAMS ACTUATOR 1333W MOTOR YELLOW GRIDDLE GRIDDLE YELL PLATEN PLATEN 120V 240V SWITCH MAIN Part # 4523133 Rev 4 (08/04/09) Page 37...
  • Page 38 Page 38 Part # 4523133 Rev 4 (08/04/09)
  • Page 39 Part # 4523133 Rev 4 (08/04/09) Page 39...

This manual is also suitable for:

Xg36-jib

Table of Contents