Component Video Out - Pioneer DVR-920H Operating Instructions Manual

14 The Initial Setup menu
Input Line System
625 System
525 System

Component Video Out

• Default setting: Interlace
You only need to make this setting if you connected this
recorder to your TV using the component video jacks.
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
If your TV is compatible with progressive-scan
component video, set this Progressive (Full) for the
highest quality picture. (If when set to Progressive (Full)
4:3 programs are 'stretched' and you can't fix this with
the controls on your TV, try the Progressive (Normal)
setting.)
If your TV is not compatible with progressive-scan video,
leave it set to Interlace.
Note that when AV1 Out (see page 112) is set to RGB, no
video is output from the component video jacks.
See also Progressive scan video in the glossary on
page 136.
112
En
Built-in tuner External input
Auto Auto
PAL PAL
SECAM SECAM
Auto
n/a
3.58 NTSC
PAL–60
Input Colour System
Interlace
Component Video Out
Progressive (Full)
AV1 Out
Progressive (Normal)
AV2/L1 In
NTSC on PAL TV
Important
If you switch to one of the progressive settings when
using a TV that is not compatible with progressive-scan
video, you will not be able to see anything displayed on
your TV. If this happens, press and hold the
the front panel, then press DISC NAVIGATOR. This will
set the recorder's video output back to Interlace.
Compatibility of this unit with progressive-scan TVs
Consumers should note that not all high-definition television sets
are fully compatible with this product and may cause artifacts to
be displayed in the picture. In case of 525 progressive scan
picture problems, it is recommended that the user switch the
connection to the 'standard definition' output (Interlace). If there
are questions regarding our TV set compatibility with this model,
please contact our customer service center.
This recorder is compatible with the following Pioneer displays
and monitors
Plasma display
• PDP-505XDE, PDP-435XDE, PDP-505HDE, PDP-435HDE, PDP-
435FDE, PDP-615EX, PDP-505HD, PDP-5030HD, PDP-4330HD,
PDP-5040HD, PDP-4340HD, Pro-1000HD, Pro-800HD, Pro-
1000HDI, Pro-800HDI, Pro-1110HD, Pro-910HD, PDP-4300, PDP-
5031, PDP-502MX
Projection monitor receiver
• SD-533HD5, SD-643HD5, Pro-710HD, Pro-610HD, Pro-510HD,
Pro-720HD, Pro-620HD, Pro-520HD, Pro-730HD, Pro-630HD, Pro-
530HD, Pro-730HDI, Pro-530HDI, Pro-700HD, SD-641HD5, SD-
582HD5, SD-532HD5
AV1 Out
• Default setting: Video
You only need to make this setting if you connected this
recorder to your TV using the AV1(RGB)-TV SCART AV
connector.
Important
• If you make a setting here that is incompatible with
your TV, the TV may not display any picture at all. If
this happens either switch everything off and
reconnect to the TV using either the supplied video
cable, or an S-video cable (see Using the S-video or
component video output on page 15 for more on this),
or reset the recorder (see Resetting the recorder on
page 123 for how to do this).
Initial Setup
Basic Input Colour System
Tuner Component Video Out
Video In/Out AV1 Out
Audio In AV2/L1 In
Audio Out NTSC on PAL TV
Language
Recording
Playback
• Video – Compatible with all TVs, but lowest quality of
the three AV settings.
button on
Video
S-Video
RGB