Pioneer DVR-920H Operating Instructions Manual page 90

09 Editing
1 Select 'Erase' from the Disc Navigator menu
options.
2 Use the
title you want to erase, then press ENTER.
Disc Navigator
Original
DVD
Play
Erase
Ttl Name
Chpt Edit
Erase Sec
Undo
3 Highlight 'Yes' to confirm, or 'No' to cancel, then
press ENTER.
4 Press RETURN to go back to the Disc Navigator
menu options, or select another title to erase.
Tip
• You can erase a title quickly by pressing CLEAR when
the title is highlighted. Confirm the edit by pressing
ENTER. (You can also use this method to erase titles
when using the Play function, above.)
Title Name (Ttl Name)
VR mode Video mode
You can give titles new names of up to 64 characters long
for VR mode and HDD recordings and 32 characters for
Video mode recordings.
1 Select 'Ttl Name' from the Disc Navigator menu
options.
2 Use the
title you want to name, then press ENTER to go to
the name input screen.
3 Input a name for the selected title.
Input Title Name
12:30 Wed 4/11 Pr 5 LP
CAPS
small
OK
• Use the
select characters.
90
En
(cursor buttons) to select the
1 2 3
12:30 Wed 4/11 Pr 5 LP DVD Remain
0h37m(FINE)
4
Erase Title?
Yes No
HDD
(cursor buttons) to select the
A B C D E F G H I J K L M . , ? !
N O P Q R S T U V W X Y Z ( ) : ;
ç
#
A A A A A A Æ E E E E I I I I
ø
D ß $ %
N O O O O O U U U U Y
< >
0 1 2 3 4 5 6 7 8 9 = _ &
+ – / @ [ ¥ ] ˆ ÷ x ± { | } ~ ¡
_
a
c £ \ § ¨ © << ¬ – ® ˚
–
´ µ ¶ ·
¿ `
¸ o
2 3 1 – << 1 / 1 / 3 /
4 2 4
Clear Space
(cursor buttons) and ENTER to
• A name generated automatically by the recorder will
already be in the name input section of the screen.
Use the
position.
• Select CAPS or small to change to upper or lower-
case, or use the CASE SELECTION buttons (
).
• You can also use the CLEAR button to delete
characters directly (press and hold for two seconds
to delete the whole name). For other remote control
key shortcuts, see Using the remote key shortcuts to
input a name below.
• For discs formatted on a different DVD recorder, you
1/1 will see only a limited character set.
4 Highlight 'OK' then press ENTER to enter the
name and return to the main Disc Navigator screen.
• To return to the main Disc Navigator screen without
saving changes to the title name, press RETURN.
5 Press RETURN to go back to the Disc Navigator
menu options, or select another title to name.
Using the remote key shortcuts to input a name
The table below shows the remote control key shortcuts
that you can use to input characters in the name input
screen. Pressing a button repeatedly cycles through the
characters shown.
If you want to enter two characters in succession that are
both on the same button (for example a P and an R),
press
between inputting the two characters.
Key
1
2 a b c 2 ä à á â ã
3
4
5
+
*1
lower-case: ÿ; upper-case: ß
buttons to change the cursor
to advance the cursor one space manually
Characters Key
6
. , ' ? ! – & 1
7
æ ç
d e f 3 è é ë ê 8
9
g h i 4 î ï ì í ¡
j k l 5 £ 0
[cursor back]
[change case] CLEAR
<space>
~
( ) _ / : ; " ` ^ @ # ∗ % ¥ | + =
{ } [ ] < >
Characters
m n o 6 ö ô ò ó ø ñ
p q r s 7 $
*1
ÿ/ß
t u v 8 ü ù û ú
w x y z 9
0
[cursor forward]
[clear character]
[finish name input]