Table of Contents
Advertisement
START/STOP ORON/OFFBUTTON
- (Wording for this button varies with model.) Use the start/stop button to turn bread
maker on and oft'. Before starting the machine, you must first progranl the bread select and crust color, plus the timer if being used.
Press start/stop
button once to turn machine on. When on, red signal light by button will glow and remain lit until bread maker is
turned off. To turn oft; press and hold start/stop
button down for about four (4) seconds or until light goes out.
When the machine is on, the colon between hours and nlinutes will flash and minutes will begin to count down the time remaining
until bread is done. When process time elapses, 0:00 will appear in display and audible alert will sound. Turn offby pressing
start/stop
button until red light goes out. Remove bread pan using oven mitts and shake loaf out of pan onto cooling rack. Cool
before slicing.
If pan is not removed ilrnnediately after baking, machine will automatically go into keep warnl mode for up to three (3) hours to keep
bread warm. The red light will relnain lit during this time and 0:00 will appear in display. Ifnlachine
is not turned offduring keep
warm period, machine will automatically turn off. If using dough setting, machine will automatically turn offupon completion of
cycle, alert will sound and display wilt reset to dough setting. Remove dough and finish as recommended in recipe being prepared.
Do not leave pan-containing dough inside machine after completion of cycle as dough will continue to rise and could overflow the
pan. See Dough section on page 19 t\_r more detail.
TOO HOT/TOO
COLD
WARNING-
If inside of oven chanlber is too hot or too cold for bread making, the word "hot" or "col"
will appear in display along with alert sounding to indicate that machine cannot be turned on. You will need to relnove pan and allow
chamber to cool or warm accordingly.
Typically "hot" will appear in display when you make consecutive loaves and forget to turn machine offbetween
loaves. Allow
chanlber to cool with cover open 10 to 15 minutes or until nlachine can be turned on without warning going oft_ If"col" appears in
display, move bread maker to a warmer area for 15 minutes or until nlachine can be turned on without warning going ofl_ If oven is
too hot, the yeast can be killed; if too cold, the growth of the yeast will be retarded.
POWER
OUTAGE
PROTECTION
- In the event of a power outage, the bread maker will turn offand autonlatically resume
the cycle in progress if power is restored within 5 to 10 seconds, If power is not restored in 5 to 10 seconds it will remain offwhen
power is restored. In this case, you must remove the contents from pan and start over with fiesh ingredients. The red on light will
remain off and the display will reset to the default setting; basic/specialty, medium crust, with 3:10 in display.
BASIC
STEPS IN MAKING
BREAD
- BEFORE
USING your bread maker for the first time, wash inside of pan and
knead bar with hot soapy water and a soft cloth, rinse and dry. Twist pan clockwise to unlock from bread
maker, then lift out. The knead bar lifts off shaft in bottom of pan. You may need to twist the bar slightly to
relnove.
Place knead bar onto shaft in pan,
nlatching hub shape with shaft shape.
Push bar down all the way.
Do not use any abrasive scouring pads or cleansers on pan or knead bar as danlage can occur. Wipe the inside of chanlber and outside
surfaces of nlachine with a soft damp cloth if necessary, dry with a soft cloth. CAUTION: To prevent personal injury or electric
shock, do not immerse bread maker base, its cord or plug in water or other liquid.
SPECIAL
NOTE: Bread pan is not inllnersible and should never be washed in an automatic dishwasher. Ilnnlersing pan in water can
cause damage to the bearing that turns the knead bar. Dishwasher cleaning can reduce the non-stick qualities of the coating, causing
sticking of the bread.
1. Position knead bar onto shaft in bottom of pan, matching hub shape to shaft shape. See Diagram 6. Make sure knead bar is pushed
onto shaft all the way. You may need to twist bar slightly to drop into place.
2. Add ingredients to pan in order listed in recipe, MAKING
SURE to add all liquids to pan first, then butter or margarine, tbllowed
by dry ingredients.
See Diagrams 7-9.
Add liquid ingredients
to pan first. Then add
butter or lnargarine,
cut into pieces for
taster blending.
Diagranl 7
Diagram 8
Diagranl 9
Add dry ingredients next. Level in pan.
Make a well in enter of dry
ingredients and add yeast to well.
Advertisement
Table of Contents
