Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Advertisement
Related Manuals for Troy-Bilt Spring Assist TB4016CC
Summary of Contents for Troy-Bilt Spring Assist TB4016CC
- Page 1 ® 2-Cycle Gas Chain saws & Model TB4218CC This product has been tested at a computed kickback angHe (CKA) and conforms to ANSI B175.1-2000, Annex C. CAN/CSA-Z62.1-03 SAVE THESE iNSTRUCTiONS NOT THROW AWAY PiN 9096-MD0701 (5/04) PRINTED IN TAIWAN...
- Page 2 THANK TABLE OF CONTENTS Thank you for buying this quality product. This modern Service Information ......outdoor power tool wiiI provide many hours of useful service. You wiiI find it to be a great labor-saving device. This operator's manual provides you with easy-to- Rules for Safe Operation .....
- Page 3 The purpose of safety symbois is to attract your SYMBOL MEANING attention to possibb dangers. The safety symbois, and their expianafions, deserve your carefui attention DANGER: and understanding. The safety warnings do not by Fa,ure to obey a themseives eiiminate any danger. The instructions or safety warning wiiI warnings they give are not substitutes for proper resuk in serious injury to yourself or to...
- Page 4 Donotoperate a chainsawthatis damaged, KmCKBACK SAFETY PRECAUTmONS improperly a djusted, or notcompletely a ndsecurely assembled. Besurethatthesaw'schainstopsmoving WARNING: KIcKBacK whenthethrottlecontrol t riggeris released. occur when the nose Shutofftheengine before settingthechainsawdown. Useextreme caution whencuttingsmalPsized brush andsaplings because slender m aterial m aycatchthe chainsawandwhiptowards youor pullyouoff balance.
- Page 5 OTHER SAFETY PRECAUTmONS Store the unit in a dry area, locked up, located up high and located out of the reach of children to prevent Do not operate a chain saw with one hand! Serious unauthorized use or damage. injury, to the operator, heipers, bystanders, or any combination of these persons may resuit from one- Never douse or squirt the unit with water...
- Page 6 SAFETY AND INTERNATmONAL SYMBOLS This operator's manuai describes safety and internationai symbois and pbtographs that may appear on this product. Read the operator's manuai for compbte safety, assembiy, operating and maintenance and repair information. SYMBOL MEANING SYMBOL MEANING ON/OFF CONTROL ON / START / RUN Indicates danger, warning, or * SAFETY ALERT SYMBOL...
-
Page 7: Safety Features
CHAroN SAW COMPONENTS SAFETY FEATURES GUIDE BAR Numbers preceding the descriptions correspond with the SAW CHAIN numbers above to help you locate the safety feature. SAW CHAIN ADJUSTMENT SCREW 2 LOW KICKBACK SAW CHAIN helps significantly reduce kickback, or the intensity of kickback, due to SPARK ARRESTER SCREEN specially designed depth gauges and guard links. - Page 8 KmCKBACK SPECmNCS KmCKBACK SPECmNCS Beware of: Pinch Kickback or fatal injury to the saw operator or to anyone standing dose by. Always be abrt. Rotational kickback and pinch-kbkback major chain saw operational dangers and the bading cause of most accidents. Beware Rotational Kickback...
- Page 9 OraLAND FUEL MmXmNGmNSTRUCTIONS Thoroughly mix the proper ratio of 2-cycle engine oil with unleaded gasoline in a separate fuel can. Use a 40:1 OHdand/or improperly mixed fueH are the main reasons fuel/oil ratio. Do not mix them directly in the engine fuel for the unit not running properly.
- Page 10 STOPPmNG mNSTRUCTmONS WARNING: Operate this unit only ina weft- ventilated 1_ Release the trigger and allow the engine to return to outdoorarea. Carbon monoxide exhaust the idle speed. fumes can be bthaIina confined area. Move the STOP switch to the STOP position. NOTE: For emergency stopping, simply activate the WARNING"...
- Page 11 Never walk in front of[ Felling is the term for cutting down a tree. Small trees up atree t hat has been ! notched.WARNING: to 6-7 inches (15-18cm) in diameter are usually cut in a singie cut. Larger trees require notch cuts. Notch cuts determine the direction the tree will fall.
- Page 12 When bucking on a dope, always stand on the uphill side. Log supported aiong entire length: Cut from top (overbuck), being careful to avoid cutting into the ground (Fig. 13). Log supported on 1 end: First, cut from bottom (underbuck) 1/3 diameter of log to avoid splintering. Second, cut from above (overbuck) to meet first cut /i / and avoid pinching (Fig.
-
Page 13: Maintenance
MAmNTENANCE SCHEDULE NOTE: Maintenance, replacement, or repair of the emission control devices and system may be Perform these required maintenance procedures at the performed by any non-road engine repair frequency stated in the table. These procedures should establishment, individual or authorized service also be a part of any seasonal tune-up. - Page 14 mNSTALL THE SAW CHAroN mNSTALL THE GUmDE BAR WARNING: Always protective gloves when handling the saw chain. loop 1. Spread chain out in a with cutting edges (A) Make sure the Chain Brake® bver is puibd back pointing CLOCKWISE around loop (Fig. 20). into the DISENGAGED position (Fig.
- Page 15 SAW CHAroN TENSION ADJUSTMENT Anew s aw chain m stretches, requiring WARNING: Always adjustment after as few as 5 cuts. This is normal protective gHoves with a new chain, and the interval between when handling the saw chain. future adjustments will lengthen quickly.
-
Page 16: Air Filter
AiR FILTER FUEL FILTER CAUTION" CAUTION" Never operate saw Never operate saw m without the air fiker. without the fuel fiker. The fuel fiRer should be replaced after each 20 Dust and dirt wiI be drawn into engine and hours of use. Drain fuel tank before changing. damage it. -
Page 17: Spark Arrester
SPARK ARRESTER SCREEN SPARK PLUG NOTE: A cbgged spark attester screen will dramatically NOTE: For efficient operation of saw engine, spark piug reduce engine performance. must be kept dean and properiy gapped. Push STOP switch down. Remove the 3 boits (A) and pull muffbr out. (Fig. 28). Remove air cbaner cover. - Page 18 STORmNG A CHAIN Sprocket Tip Lubrication CAUTION" The sprockettipon m your new saw has been prequbdcated at the factory. Failure to performance and seizure, voiding the Storing a chain saw for Honger than 30 days requires manufacturer s warranty. storage maintenance. UnHessthe storage instructions are foUowed, fueHremaining in the carburetor wiU evaporate, Heaving gum-Hike deposits.
- Page 19 GUmDE BAR MAmNTENANCE: CHAIN REPLACEMENT mNFORMATmON Most guide bar proMems can be prevented mereiy by There may be other quality equivabnt replacement keeping the chain saw well maintained. components for achieving kickback protection. hsuffbbnt guide bar iubrbafion and operating the saw with chain that is too tight will contribute to rapid bar wear.
- Page 20 CAUSE ACTmON Incorrect starting procedures Follow instructions in the Starting/Stopping section Incorrect carburetor mixture adjustment setting Have carburetor adjusted by Authorized Service Center FouHed spark pHug Clean / gap or replace plug CAUSE ACTmON Incorrect Heverposition Move to RUN position Dirty spark arrester screen Replace spark arrester screen.
- Page 22 Description Description Description Item Paris Item Paris Item Parts 9238=MD0701 ASS'Y 1:30 9082=310501 SWITCH 9228=310504 MUFFLER ASS'Y 9157=310502 CAP, SEARING 1=31 9WFB=05=21 WASHER 9SXDB=O8=70 SCREW 9DB-620101 BEARING 1-32 9SKKBY8/16-0 SCREW 1-62 9010_310502 CABLE, THROTTLE 9228-310508 CRANK/ROD ASS'Y 1=33 9068=MD0791 HANDLE, FRONT 1=63 9129=319504...
- Page 23 (90) days from the date of original retail related expenses, or for rental expenses purchase for any Troy-Bilt product that is used for rental or temporarily replace a warranted product. (Some states commercial...