"IIIIIi'IOUBL HOOTINQ
The subtitle
language
cannot
be
changed
or turned
off.
The angles cannot
be changed.
Recording does not stop immediately
after you press [STOP n].
The disc tray does not open when you
press [OPEN/CLOSE _].
"Repairing"
appears on the TV screen.
In a case you intend to cancel the
repairing process.
• Multilingual
subtitle
are not recorded
on the DVD-video.
• Multi-angles
are not recorded
on the DVD-video
being played
back.
• The angle-change
operation
is whenever
possible as long as the disc
contains
a multi-angle
portion.
Actual change will be performed
when
the portion
has come up.
• The DVD-video
prohibits
changing
angles.
• Try changing
the angle using the DVD-video's
menu.
• It may take a few seconds for the unit to input disc data before
recording
stops.
• It may take a few seconds for the disc tray to open after you have
recorded
or edited a disc. This is because the unit is adding
disc data to
the disc.
• If there is a power failure or unplugging
during
recording,
finalizing,
formatting
or editing
(even after "Repairing"
disappears),
a repairing
process will begin automatically
just after turning
the unit on again.
It may take several minutes
up to about
several hours.
• If you intend
to cancel the repairing
process, press [__OPEN/CLOSE]
on the front panel, then select "Yes" and press [ENTER[. After that, press
[OPEN/CLOSE
_] to take out the disc. The disc canceled
during the
repairing
process MAY NOT work.
No image from HDMI connection.
There is no sound or the sound is
distorted.
• Check the HDMI connection.
(Check the status of the HDMI related
indications.)
• Check whether
the connected
monitor
device or other device supports
HDCP. (This unit will not output
a video signal unless the other device
supports
HDCP.)
• Check the setting
of HDMI.
• Check whether
the output
format
of this unit (HDMI FORMAT) matches
the supported
input format
of other connected
device.
• If the unit is connected
to the unauthorized
display device with an
HDMI cable, the audio/video
signal may not be output
when playing
back a commercial
DVD-video.
• The HDMI sound is not output
when "HDMI Audio"
is set to "OFF".
• Check the RCA audio cable connection.
If you are using HDMI-DVl
conversion
cable, you must connect
the RCA audio cable, too.
• Check whether
the output
format
of this unit (HDMI FORMAT) matches
the supported
input format
of other connected
device.
There is no picture.
• If you connect
the cable to S-VIDEO OUT/COMPONENT
VIDEO OUT/
HDMI OUT jack, try connecting
it to AUDIO / VIDEO OUT jack instead.
Picture noise appears.
• Head cleaning
for VCR may be necessary. Refer to "Auto Head Cleaning"
(page 5).
• Adjust tracking
control for better picture by pressing [TRACKING
A / V]
while you are playing back a cassette tape.
The cassette tape does not play back.
• No cassette tape is inserted.
The tape ejected after you press
• Make sure the cassette tape has an erase-protection
tab when you
[REC O].
record to a cassette tape. If needed,
cover the hole with cellophane
tape.
The remote control
does not function.
• Check if a cassette tape is in this unit.
The motor rotates even when
• The motor
may rotate for the duration
of approximately
5 minutes
for
playback
/ recording
is stopped,
efficient
operation.
This is not a malfunction.
104
EN
E9KGAUD
D-VR610KU
EN.indd
104
,,F_+_,/.h_
2007/12/18
17:11:36