Table of Contents
Advertisement
Quick Links
Models:
CL36D
CR36D
Wood Burning Fireplace
•
Important operating
a n d m a i n t e n a n c e
instructions included.
WARNING
If the information in these instruc-
tions is not followed exactly, a
fi re may result causing property
damage, personal injury, or death.
• Do not store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of
this or any other appliance.
• Do not overfi re. Overfi ring will void your
warranty.
• Comply with all minimum clearances to
combustibles as specifi ed. Failure to
comply may cause house fi re.
Installation and service of this fi replace
should be performed by qualifi ed personnel.
Hearth & Home Technologies suggests NFI
certifi ed or factory-trained professionals, or
technicians supervised by an
NFI certifi ed professional.
CAUTION
DO NOT DISCARD THIS MANUAL
•
Read, understand
and follow these
instructions for safe
i n s t a l l a t i o n a n d
operation.
Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12
Owner's Manual
Installation and Operation
•
Leave this manual with
party responsible for
use and operation.
WARNING
Hot screen/mesh and glass doors will cause burns.
•
DO NOT touch screen/mesh or glass doors until
cooled
•
NEVER allow children to touch screen/mesh or glass
doors
•
Keep children away
•
CAREFULLY SUPERVISE children in same room as
fi replace.
•
Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
fl ammable materials.
•
Keep clothing, furniture, draperies and other
fl ammable materials away.
WARNING
Fire Risk
•
For use with solid wood fuel or decorative
gas appliance only.
•
DO NOT install unvented gas logs.
HOT SURFACES!
Screen/mesh, glass doors
and other surfaces are hot
during operation AND cool
down.
1
Advertisement
Chapters
Table of Contents
Related Manuals for Heatiator CL36D
Summary of Contents for Heatiator CL36D
- Page 1 • For use with solid wood fuel or decorative technicians supervised by an gas appliance only. NFI certifi ed professional. • DO NOT install unvented gas logs. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12...
-
Page 2: Congratulations
CONTACT: HEARTH & HOME TECHNOLOGIES INC., ADJUST DAMPER TO THE FULLY OPEN POSITION. 1915 W. SAUNDERS ST., MT. PLEASANT, IA 52641. Note: An arrow ( ) found in the text signifies change in content. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 3: Table Of Contents
Tools and Supplies Needed E. Contact Information G. Fireplace System Requirements H. Inspect Fireplace and Components Framing & Clearances A. Select Fireplace Location B. Clearances C. Sidewalls/Surrounds D. Frame the Fireplace Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 4: Limited Warranty
Limited 3 years Firebox and heat exchanger Lifetime All replacement parts 90 Days beyond warranty period See conditions, exclusions, and limitations on next page. 4021-645C 12-29-10 Page 1 of 2 Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... - Page 5 THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE. 4021-645C 12-29-10 Page 2 of 2 Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12...
-
Page 6: Listing And Code Approvals
NOTICE: This fireplace is tested and approved as a decorative fireplace. It should not be factored as a primary heat source in residential heating calculations. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 7: User Guide
(not shown) Section 2.H. Outside Air Control Handle Wood Fuel Section 2.I. Section 2.M. IN - closed OUT - open Hearth Clear Space Section 2.L. Figure 2.1 General Operating Parts Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 8: Seasoned Wood
Add a minimum of three average size pieces of split firewood, placed to allow combustion air and flames between them. CAUTION! Odors and vapors released during initial operation may be irritating to sensitive individuals. Open windows for air circulation. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 9: Glass Doors
HOT when fireplace is in operation. Adjust BEFORE lighting fire. 18 in. (45.7 cm) Clear Space from Opening of Fireplace 48 in. (121.9 cm) Clear Space Front of Fireplace Figure 2.3 Clear Space Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 10: Wood Fuel
Do not poke or stir the logs while they are burning. Use formation of creosote. only firelogs that have been evaluated for the application in manufactured fireplaces and refer to firelog warnings and caution markings on packaging prior to use. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 11: Maintenance And Service
Slip Chase Section TCT375 ST375 TS345/TS345P TR344/TR342 Terra Cotta Square Square Round Termination Cap Termination Cap Termination Caps DT SERIES Termination Cap Figure 3.1 Chimney & Termination Cap Cleaning Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 12: Check Firebox Refractory
Clean glass with a non-abrasive commercially available cleaner or ashes: • Light deposits Use household glass cleaner • Heavy deposits Use wood ash on damp cloth or, Use commercial fireplace glass cleaner (consult with your dealer) Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 13: Troubleshooting Guide
Add glass doors to slow down air flow. Overdrafting Check for correct vent height; too much vertical height creates overdrafting. Check location of vent termination (refer to chimney assembly section). Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 14: Getting Started
(1.83m) off (Section 11) ground level. Hearth extension Outside (Section 11) combustion air Factory-built fireplace (Section 7) Protective metal hearth strip(s) (Section 7) Figure 5.1 Typical Fireplace System Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 15: Design And Installation Considerations
Tight sealing construction of the structure • Mechanical exhausting devices NOTICE: Hearth & Home Technologies Inc. recommends • Improper location of the chimney the use of direct vent fireplaces in basements. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 16: Locating Fireplace & Chimney
• Too close to tree Recommended: • Below adjacent structure • Insulated exterior chase • Lower roof line • Avoid outside wall in cooler climates Windward Leeward Multi-level Roofs Figure 5.2 Recommended Chimney Locations Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 17: Tools And Supplies Needed
Hearth Refractory • Grate Assembly • Hearth Extension (required, sold separately) • Chimney Air Kit (required in Canada) • Chimney System (required, sold separately) • Termination Cap (required, sold separately) Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 18: Framing & Clearances
45 in. • Clearances (Section 6.B.) • Mantel Projections (Section 11.E.) 23 in. • Fireplace Dimensions (Section 13.A.) 48 in. Min. Figure 6.1 Fireplace Locations (Framing dimensions shown) Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 19: Clearances
1/2 in. (13 mm) to back & side of appliance 0 in. to floor Figure 6.2 Clearances to Combustible Materials Note: Chimney air kit is not shown, but is required in Canada. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 20: Sidewalls/Surrounds
50 deg 16 3/4 in. Minimum 18 in. Min. 14-1/2 in. 20 in. 39 deg 50 deg 16 3/4 in. 18 in. Min. Minimum Figure 6.3 Mantel Leg or Wall Projections Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 21: Frame The Fireplace
Drywall fireplace opening. 42-1/2 in. (1080 mm) 1/2 in. (13 mm) Clearance 22 1/2 in. (572 mm) * 1/2 in. (13 mm) Clearance Figure 6.4 Framing the Fireplace Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 22: Installation Of Fireplace
• Check fireplace opening for square to ensure proper fit of glass doors. Measure diagonals of fireplace opening to make sure they are equal. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... - Page 23 Figure 7.4 Outside Combustion Air Placement Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12...
-
Page 24: Install Outside Air Kit
Blockages could cause combustion air starvation. Flexible Duct (not supplied) Outside Air Plate Outside Air Assembly Hood 2 Wire Ties Figure 7.5 Outside Air Installation Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 25: Chimney Assembly
Lock chimney sections together firmly to resist movement Ceiling firestops are required where chimney passes through ceiling or floor Figure 8.1 Typical Chimney System - Guidelines for Chimney System Installation Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 26: Chimney Requirements
(no offset-return) SL312 10-3/4 Effective Height 50 ft (15.24 m) max. height SL318 16-3/4 SL324 22-3/4 SL336 34-3/4 SL348 46-3/4 1187 * Dimensions reflect effective height. Figure 8.2 Chimney Requirements Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 27: Using Offsets/Returns
2629 49-1/4 1251 94-1/2 2400 Proper assembly of air-cooled chimney parts result in an overlap at chimney joints of 1-1/4 in. (32 mm). Effective length is built into this chart. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 28: Assemble Chimney Sections
Use same dimensional lumber for framing ceiling firestop and joists. Catalog # Angle FS338 14-1/2 14-1/2 0° Figure 8.4 Assembling Chimney Sections FS339 14-1/2 18-3/8 15° FS340 14-1/2 30° Figure 8.5 Installing the Ceiling Firestop Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 29: Install Attic Insulation Shield
Attic Insulation Shield 14-1/2 in. (368 mm) diameter 6 Tabs bent in 90° Insulation Insulation 10-1/2 in. Ceiling Firestop Pipe (267 mm) Figure 8.8 Install Attic Insulation Shield (firestop below ceiling) Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 30: Cut Out Hole In Roof
All nail heads must be caulked with a roofing sealant. • Caulk the overlap seam of any exposed pipe sections that are located above the roof line to prevent leaks. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 31: Chimney Termination Requirements
In a staggered installation with both gas and wood terminations, the wood termination cap must be higher than the gas termination cap. Figure 8.10 Multiple Chimney Locations Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 32: Chase Installations
• Failure to prevent contact between insulation or other materials and chimney system may cause overheating Figure 9.1 Chase Assembly and fire. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 33: Install Fireplace & Chimney
Chase Top Construction Chase Termination cap pipe and chimney section must be snapped together to maintain an overlap of 1-1/2 in. (38 mm). Figure 9.4 Installing a TR344 Round Termination Cap Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... - Page 34 1-1/2 in. (38 mm) Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm) Figure 9.8 Installing a TCT375 Terra Cotta Cap Figure 9.6 Installing an ST375 Square Termination Cap Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12...
-
Page 35: Shrouds
Width Base Dim. Min. 17 x 17 22 x 22 20 x 20 Base Dim. 432 x 432 559 x 559 508 x 508 Figure 10.2 Open Top Shroud Dimensions Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... - Page 36 Min. Height Above Radiation Shield Termination Height 3 in. (76 mm) Radiation Minimum Shield Height Base Dimension Min. Opening Width Min. Opening Width Min. Opening Height Figure 10.4 Roofed Style Shroud Dimensions Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12...
-
Page 37: Finishing
0.20 5-1/8 in. Common Brick 0.20 5-1/8 in. Ceramic Tile 12.50 0.08 12-1/4 in. Armstrong™ Privacy Guard Plus 0.46 2.18 1/2 in. Marble 14.3-20.0 0.07-0.05 14-5/8 in. - 20-3/8 in. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 38: Finishing Material
2 in. (51 mm) Figure 11.3 Decorative Facing Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 39: Combustible Mantel
Measured from top of fireplace opening slate, glass, plasters Seal joint with non-combustible sealant Figure 11.4 Clearances to Mantels or other Combustibles above Fireplace Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 40: Sidewalls/Surrounds
18 in. Min. 14-1/2 in. 20 in. 39 deg 50 deg 16 3/4 in. 18 in. Min. Minimum Figure 11.5 Mantel Leg or Wall Projections (acceptable on both sides of opening) Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 41: Accessories
Combustible materials may be located at zero clearance to gas line Repack beyond 4 in. (102 mm) insulation from fireplace side. knockout 4 in. (102 mm) Figure 12.1 Gas Line Installation Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 42: Reference Materials
Inlet Tube Assembly Assembly 2 Wire Ties AK14 Bi-fold Glass Doors Outside Air Kit with End Panel DM1436 Series See your Heatilator dealer for a complete listing of optional components. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... -
Page 43: Chimney Components
(305 mm) Diameter Height 5-1/4 in. 10-1/2 in. 4-3/4 in. (133 mm) 4 in. (102 mm) (267 mm) (121 mm) 10-1/2 in. (287 mm) SL315/SL330 Offset/Return CAK4A Chimney Air Kit Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... - Page 44 (397 mm) TR344 Round Termination Cap 26 in. ST375 Square Termination Cap CT-3A 34-3/4 in. (883 mm) 32-1/2 in. (826 mm) TR-TVK TR Top Vent Kit TR342 Round Telescoping Termination Cap Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12...
- Page 45 DTO134 / DTO146 Decorative Caps DTO134 LDS33/LDS46 Decorative Shroud DTO146 Catalog # 22.7 LDS33 1168 LDS46 1219 1829 DTS134 21.18 DTS146 21.18 1168 LDS-BV Decorative Shroud Catalog # 12.5 15.5 LDS-BV Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12...
-
Page 46: Service Parts
11847 Standoffs - Top Qty. 4 req. 11864i Strip Protector Qty. 3 req. 18320 Touch-up Paint 71479 Installation Instructions & Owner’s Manual 12538 **Screen length changed from 18.62” to 19.00 Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12... - Page 47 11847 Standoffs - Top Qty. 4 req. 11864i Strip Protector Qty. 3 req. 18320 Touch-up Paint 71479 Installation Instructions & Owner’s Manual 12538 **Firescreen length changed from 18.62” to 19.00” Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12...
-
Page 48: Contact Information
Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12...
Need help?
Do you have a question about the CL36D and is the answer not in the manual?
Questions and answers