Table of Contents

Advertisement

Models:
CD4236IR-C
CD4842IR-C
CD4236ILR-C
CD4842ILR-C
• Important operating
a n d m a i n t e n a n c e
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppli-
er's instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer's instructions
and the manufactured home construction and safety standard,
Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
NOTICE
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
Heatilator • CD4236IR-C, CD4842IR-C • 2207-900 Rev. J • 11/11
Owner's Manual
• Leave this manual with
party responsible for use
and operation.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fi replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other fl ammable
materials.
• Keep clothing, furniture, draperies and other fl ammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fi tter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.
Installation and Operation
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CD4842IR-C and is the answer not in the manual?

Questions and answers

Summarization of Contents

1 Listing and Code Approvals
A. Appliance Certification
Details on the appliance's certification and standards compliance.
B. Tempered Glass Specifications
Specifications regarding the tempered glass used in the appliance.
C. BTU Specifications
Technical specifications for the appliance's BTU output.
D. High Altitude Installations
Guidelines for installing the appliance at high altitudes.
E. Non-Combustible Materials Specification
Definition and specification of non-combustible materials.
F. Combustible Materials Specification
Definition and specification of combustible materials.
G. Electrical Codes
Applicable electrical codes and wiring requirements.
H. Requirements for the Commonwealth of Massachusetts
Specific installation requirements for Massachusetts.
2 Operating Instructions
A. Gas Fireplace Safety
Important safety precautions for operating the gas fireplace.
B. Your Fireplace
Introduction to the fireplace and its operation.
C. Fan Kit (optional)
Information on adding and using an optional fan kit.
D. Clear Space
Requirements for maintaining clear space around the fireplace.
E. Decorative Doors and Fronts
Guidelines for installing approved decorative doors and fronts.
F. Fixed Glass Assembly
Information about the fixed glass assembly.
G. Remote Controls, Wall Controls and Wall Switches
Instructions for operating the fireplace via remote or wall controls.
H. IPI Battery Tray/Battery Installation
Details on installing the battery backup for the ignition system.
I. Control Module Operation
Explains the operation and settings of the control module.
J. Before Lighting Fireplace
Pre-lighting checks and procedures by a qualified technician.
K. Lighting Instructions (IPI)
Step-by-step guide for lighting the IPI fireplace.
L. After Fireplace is Lit
Initial break-in procedure and post-lighting steps.
M. Frequently Asked Questions
Common issues and their solutions for fireplace operation.
3 Maintenance and Service
Homeowner Maintenance Tasks
Routine maintenance tasks for homeowners, including glass, doors, and venting.
Technician Maintenance Tasks
Essential maintenance tasks to be performed by a qualified service technician.
C. Logs/Grate and Valve Assembly Removal
Procedures for removing logs, grate, and valve assembly for servicing.
D. Burner Identification/Verification
Steps for identifying and verifying burner components.
4 Getting Started
A. Typical Appliance System
Overview of the direct vent gas appliance system and its components.
B. Design and Installation Considerations
Key factors to consider before designing and installing the appliance.
C. Tools and Supplies Needed
List of essential tools and supplies required for installation.
D. Inspect Appliance and Components
Steps for inspecting the appliance and its components upon arrival.
5 Framing and Clearances
A. Selecting Appliance Location
Guidelines for choosing a suitable location for the appliance.
B. Constructing the Appliance Chase
Instructions for building the chase structure for the appliance.
C. Clearances
Specified clearances required for installation around the appliance.
D. Mantel and Wall Projections
Requirements for mantel and wall projections near the appliance.
6 Termination Locations
A. Vent Termination Minimum Clearances
Minimum required clearances for vent termination locations.
7 Vent Information and Diagrams
A. Approved Pipe
Information on approved vent pipes and components.
B. Vent Table Key
Explanation of abbreviations used in vent diagrams and tables.
C. Use of Elbows
Guidance on using elbows in vent pipe configurations.
D. Measuring Standards
Standards used for vertical and horizontal vent measurements.
E. Vent Diagrams
Visual representations of different vent configurations and their requirements.
8 Vent Clearances and Framing
A. Pipe Clearances to Combustibles
Critical clearances required between vent pipes and combustible materials.
B. Wall Penetration Framing
Framing requirements for wall penetrations for vent systems.
C. Install the Ceiling Firestop
Instructions for installing ceiling firestops for vent systems.
D. Install Attic Insulation Shield
Guidance on installing attic insulation shields for vent pipe protection.
E. Installing the Optional Heat-Zone® Gas Kit
Instructions for installing the optional Heat-Zone® gas kit.
9 Appliance Preparation
A. Top Vent
Preparation steps for the top vent configuration.
B. Rear Vent
Preparation steps for the rear vent configuration.
C. Installing the Non-combustible Board
Instructions for installing the non-combustible board.
D. Securing and Leveling the Appliance
Procedures for properly securing and leveling the appliance.
10 Installing Vent Pipe (DVP and SLP Pipe)
A. Assemble Vent Sections (DVP Pipe Only)
Steps for assembling DVP vent pipe sections.
B. Assemble Vent Sections (SLP Pipe Only)
Steps for assembling SLP vent pipe sections.
C. Assemble Slip Sections
Instructions for assembling slip sections of vent pipe.
D. Secure the Vent Sections
Methods for securing vent pipe sections properly.
E. Disassemble Vent Sections
Procedures for safely disassembling vent pipe sections.
F. Install Decorative Ceiling Components (SLP only)
Installing decorative components for SLP vent systems.
G. Install Metal Roof Flashing
Installing metal roof flashing for vent pipe through the roof.
H. Assemble and Install Storm Collar
Steps for assembling and installing the storm collar.
I. Install Vertical Termination Cap
Instructions for installing the vertical termination cap.
J. Install Decorative Wall Components (SLP only)
Installing decorative wall components for SLP vent systems.
K. Heat Shield Requirements for Horizontal Termination
Requirements for heat shields used with horizontal vent terminations.
L. Install Horizontal Termination Cap (DVP and SLP Pipe)
Steps for installing horizontal termination caps for DVP and SLP pipes.
11 Gas Information
A. Fuel Conversion
Information on converting the appliance to different gas types.
B. Gas Pressure
Details on gas pressure requirements and verification.
C. Gas Connection
Proper procedures for connecting the gas supply to the appliance.
D. High Altitude Installations
Guidelines for installing the appliance at high altitudes.
12 Electrical Information
A. Wiring Requirements
Electrical wiring standards and requirements for the appliance.
B. IntelliFire Plus™™ Ignition System Wiring
Wiring diagram and instructions for the IntelliFire Plus™™ ignition system.
C. Optional Accessories Requirements
Requirements for optional accessories like wall switches and thermostats.
D. Electrical Service and Repair
Safety precautions and procedures for electrical servicing.
E. Junction Box Installation
Instructions for installing the appliance's junction box.
F. Wall Switch Installation for Fan (Optional)
Installing a wall switch for an optional fan.
13 Finishing
A. Mantel and Wall Projections
Requirements for mantel and wall projections, including clearances.
B. Facing Material
Guidelines for applying facing and finishing materials around the appliance.
14 Appliance Setup
A. Appliance Preparation Steps
Initial steps including removing glass, shipping materials, and cleaning.
B. Accessories and Ember Placement
Installing accessories and proper placement of ember material.
C. Log Assembly and Fixed Glass
Installing log assembly and handling fixed glass assembly.
D. Trim, Surround, and Air Shutter
Installing trim/surround and adjusting air shutter settings.
15 Troubleshooting
A. IntelliFire Plus™™ Ignition System
Troubleshooting guide for issues with the IntelliFire Plus™™ ignition system.
16 Reference Materials
A. Appliance Dimension Diagram
Diagrams showing the physical dimensions of the appliance.
B. Vent Components Diagrams
Diagrams illustrating various vent pipe components and their specifications.

Table of Contents