Specifications; Troubleshooting Tips; Care And Cleaning - GE Appliances Profile GXCF35GBS Owner's Manual

Start Up and Operation Adjustment--Clock, Hot
Water Temperature, Energy Saver Cycle and Timer
Important: Sanitize the unit and install a full bottle of water before
plugging the unit into an electrical outlet. An error code will be
displayed and the alarm will sound if the dispenser is operated
without water--see Troubleshooting tips.
Plug the power cord into a properly grounded electrical outlet.
Press the SETbutton to ad\mlce the control to the next
ti_atm'e needing an initial setting or a(!iusnnent.
Setting the Clock. Adjust the hom_ including the A&I/PM
setting using the _ and _ buttons. Press the SETbutton to
advance to the minute
a@lsnnent,
then again to select the
day ot the week (ie, WE for X4'ednesday). The clock time nlust
be set to initiate the energy saver wcle.
Water Temperature Scale and Hot Water Temperature Set Point.
Select the temperature scale ([*_Fahrenheit or C--Celsius)
to display the temperature \_flues, then press the SETbutton
to
a(!just
the hot water temperature set point. Tile hot water
can be a_!justed from 195°F to 150°F (91°C to 66°C) or shut
offwhen a(!justed below 150°F (66°C). The detimlt is set at
175°F (80°C) fin" optimal energy perfimnance.
Press the SET
button again to accept the temperature setting and advance
to the Energy' Saver cycle start and stop time. NOTE." The cold
wamr and compartment temperature is not a(!justable.
Adjusting the Energy Saver Cycle Start and Stop times. Select the
Monday through Friday start time fin" hot water operation
prompted
bv the light blue clock and the "/I/10
TU WETHFR"
display. Press the SETbutton to enter tile stop time tOT hot
water operation as indicated bv the red clock icon. Next set
the start and stop times fin" Saturday and Sunday. Saturday
and Stmday operation finles are set'independei{fl) as
previously described. The detimlt Energy' Saver cycle is set at
the ti_cto_ T fin" optimal energy' perfimnance--hot operation
to start at 6:00 am and stop at 8:00 pro. NOTE." The chiller
compartment will remain in cooling operation at all times
whether the Energy' Saver cycle is on or off. \4]_en you have
reached the end of the set up procedure, the SET light will
go out. Set up is complete.
_Mter initial set up and a(!jusnnent is complete, confim/that a
till bottle of water has been installed.
Press the @ (Power ON/OFF) button to begin operation of
the dispense_:
timer Operation. Press the TIMER/STARTbumm, then a(!just
the horus ttsing the & and _ bumms. Press the
TIMER/START
button again, then at!just the minutes.
Press the TIMER/START
button again to start the fime_: Press the STOP/CANCEL button
to pause the fime_: Press the STOP/CANCEL button again to
cancel the time_; Once the timer has completed its countdown,
the almm will sound three times, The alaml will continue to
sound evely 15 seconds until tile tinier has been canceled. The
timer _111count down time fin" up to 12 hotu_ and 59 minutes.
Specifications*
Cooled Water Temperature Setting: 40°F (4°C)
Water Cooling Rate: 0.26 gallons (l liter) per hour
Heated Water Temperature Setting: A(!justable ti'om 150°F to
195°F (66°C to 91°C)
Water Heating Rate: 0.8 gallons (3 liter) per hour
Troubleshooting Tips.
Compartment Temperature: <46°F (<7.8°(;)
Capacity: 3 or 5 gallon ( 11.4 or 19 liter) bottle
Power Consumption-Heating: 480 Watts max.
Cooling: 125 Watts max.
'::Tested _ith 75°F (24°C) ambient tempemnu'e, stea_' state opelafion
;: Possible Causes What To Do
Waterdispenserleaks Crack or pin hole in bottle. • I_eplace with a new bottle of water:
from the outside
Waterhaspoortaste Separator needs clemlh_g. • See Cleaning the Separator.
or odor
Unit needs to be sanitized,
"See Cleaning and Sanitizing the Water Tanks.
Water not hot enough Dispenser is unplugged. * Push the l)ltw_ completely, into the outlet.
or cold enough The fuse is blown/circuit * Replace house fl/se or reset tile house circtdt breakel:
breaker is tripped. •/f too re:my items are plugged into a single circtfit,
move some items to a different circuit.
All the water in the water tank * X_'ait 30 minutes fin" water to heat or cool.
has been used.
Temperature limiter tripped. • Turn off dispense1: X_'ait five minutes; then mm back on.
_4.fit 30 minutes fin" water to heat or cool.
Didn't select proper hot water • At!just hot water setting (see Start Up and Operation
temperature. Adjustment).
Water dispenser does Empty water bottle. * Replace with a new bottle of water:
not work--No water flow
Mineral deposits clogghag tanks, • See Care and Cleaning.
Cold water button Chiller door has been left open. * Close chiller (_h>o_:
does not dispense Ice bnildup blocking water flow.
* Ztlrn Off power overnight ;ill(1
tt/rn
on ill the
I/lorning.
Compressor does
not Normal Operation Compressor * \Mfit flw up to 3 minutes fin the compressor to star*.
startwhen snowflake
start is delayed by up to 3 mhmtes
iconmotionappears
to prolong the compressor life.